MRP Ribbon Coil Manual
PDF manual · 6 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your MRP Ribbon Coil manual using AI
Get instant AI answers from your MRP Ribbon Coil manual
Ask anything about the MRP Ribbon Coil. Answers come from this manual, with the pages they are based on.
Ribbon Coil Maintenance Schedule
Clean dirt and mud from stanchions after every ride.
Verify all adjustment controls are functioning correctly before each ride.
Change bath oil every 50 hours in normal conditions or every 30 hours in muddy conditions.
Replace wiper seals every 100 hours in normal conditions or every 75 hours in muddy conditions.
Perform a full damper oil change every 200 hours of use.
Inspect and torque all fasteners to specified values every 30 hours.
Ask a Question
Do you recommend Ribbon Coil?
Yes NoFrequently Asked Questions
Ramp Control primarily adjusts high-speed compression behavior by managing airflow during late travel. It is designed to boost the ending-stroke spring curve, reducing bottom-out tendency when set firmer while keeping low- and moderate-speed movement freer.
Is this answer helpful?
Use the red rebound knob on the damper-side bottom. Turning clockwise increases rebound damping (slower return), and counter-clockwise decreases it (faster return). Start from the chart or a conservative baseline, then adjust until the wheel tracks terrain without bouncing.
Is this answer helpful?
Compression damping controls how the fork resists compressing on impacts, changing the feel of support through compression. Spring rate and preload control how much force the spring requires to move. Adding compression damping can feel firmer, but it does not change spring rate.
Is this answer helpful?
Follow the hour-based schedule: bath oil every 50 hours normal or 30 hours muddy; wiper seals every 100 hours normal or 75 hours muddy; damper oil every 200 hours. Each ride, clean dirt and mud from stanchions and inspect fasteners, stanchions, and adjustment controls.
Is this answer helpful?
The fork features a post mount for 180mm rotors. If you want a larger rotor, use the appropriate disc brake adaptor recommended by your brake manufacturer. Using the wrong setup can create unsafe braking conditions.
Is this answer helpful?
Compress the fork fully to bottom out and confirm at least 1/8 inch (3mm) clearance between the crown and the highest point of the tire. This helps ensure safe operation across riding conditions.
Is this answer helpful?
To request warranty inspection, use the warranty contact form on MRPbike.com or contact MRP to set up a Return Authorization (RA) number. Pack and ship the fork with the RA number clearly marked. The manual also notes what is not covered, including damage from crashes, improper installation, missing serial numbers, and normal wear items like seals and wipers.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Ramp Control lets you adjust the ending-stroke curve independently, improving support on high-speed hits.
- Coil preload tuning and a wide adjustment range help you reach the sag and feel you want.
- Rebound and compression provide clear, click-based tuning for traction and small-bump control.
- Defined maintenance intervals (oil, seals, inspections) support long-term performance and reliability.
- 180mm post mount is straightforward, with guidance for larger rotors using correct adaptors.
Disadvantages
- Damping and preload tuning require careful adjustment; wrong setup can reduce comfort or control.
- Mud-heavy riding shortens oil and wiper seal service intervals, increasing upkeep.
- Setup steps include detailed installation checks like steerer length and minimum clearance verification.
- Changing travel and internal parts involves multiple tools and careful oil handling.
Product Specification
Type
Suspension Fork
Colors
black
Wheel size
27.5"/650B
Travel
6.30"
Spring type
Coil
Steerer
tapered 1.5"
Stanchion diameter
1.38"
Axle system
15mm thru-axle (Boost)
Brake system
Disc brake
Brake mount
Postmount
Weight
4.59 lb
Product Description
MRP Ribbon Coil 27.5" 160mm Suspension fork - Setup, tuning, and care
The MRP Ribbon Coil 27.5" 160mm Suspension fork Manual is built for riders who want plush coil traction with confident support on fast, technical lines. With 160mm of travel, this fork blends spring comfort with independent tuning features so you can dial the feel for small-bump sensitivity, mid-stroke control, and end-stroke support.
One of the signature features is Ramp Control, which reshapes the ending-stroke behavior without tying your settings directly to rebound or preload. Ramp Control offers 20 clicks. When set firmer, it increases resistance during high-speed compression to help reduce bottom-out tendency while keeping low- and moderate-speed movement more free-flowing. For quick fine-tuning, the rebound knob (red, on the bottom of the damper side) provides about 20 clicks. More rebound damping slows the return after a bump, while less rebound speeds it up so your tire can track and avoid bouncing off the terrain.
Spring behavior is tuned with adjustable preload underneath the cap on the spring-side leg. The fork ships with zero preload, and you can add preload using a 3mm hex fitting over a roughly 10.5 rotation range. A supplied preload washer can add the equivalent of two more rotations, raising the force required to bottom out by about 7 percent. If your desired sag is hard to reach, the manual suggests moving to a lighter or firmer spring rate.
To customize compression feel, use the top damper-side compression dial with 8 clicks. The factory starts at the least-damped position. Turning clockwise increases compression damping for a firmer, more supportive feel, which can pair well with aggressive riding and bigger hits. You do not change spring rate with compression; it is a separate damping adjustment.
Installation and safety guidance matter. The fork uses a post mount for 180mm rotors; for larger rotors, use the recommended adaptor from your brake manufacturer. The manual emphasizes correct steerer tube length, proper headset assembly, axle installation, and checking minimum tire-to-crown clearance at full bottom-out (with at least 1/8 inch, or 3mm, clearance).
Maintenance essentials (hours): replace bath oil every 50 hours in normal conditions or 30 hours in muddy conditions; replace wiper seals every 100 hours normal or 75 hours muddy; change damper oil every 200 hours; inspect stanchions, fasteners, and controls regularly; and clean dirt and mud from the stanchions every ride.
Notes: Register your fork online at MRPbike.com under SUPPORT, and follow the provided torque specs to ensure safe, consistent performance.
Search for 67,706 Manuals online
Type-in Brand or Model