Manual.ly Logo

Moser Primat 1230-0053 Manual

0.0 · 0 Ratings

PDF manual · 148 Pages

English

M: QW-35-FL
page

/ 148

Loading...
c49836c9741550c9a8ff3622d8c668530e43 page d
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
13
Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power
supply.
f Only operate the appliance with the voltage
stated on the nameplate.
Mains operation
1. Insert the appliance plug into the mains socket.
2. Switch on the appliance using the on/off switch (Fig.
2
ⓐ
) and, after use, switch it off again (Fig. 2
ⓑ
).
Operation
Cutting length adjustment
Without the attachment comb, the normal cutting length of
the appliance is approx. 0.7 mm. The cutting length can be
adjusted between 0.7 and 3 mm, even when the appliance
is in use.
1. Slide down the locking switch (B) (Fig. 3
ⓑ
)
2. By moving the adjustment lever at the side (Fig. 4
ⓐ
),
it is possible to set the cutting length to 6 pre-set posi-
tions (
MultiClick).
3. Sliding the locking switch (B) upward (Fig. 3
ⓐ
) unlocks
the setting and restores the normal cutting length of
approx. 0.7 mm.
Cutting with the attachment comb
The appliance can also be operated with attachment
combs. Attachment combs can be used to extend the cut-
ting length range.
Depending on the model, various attachment combs are
included in the scope of supply. Attachment combs #1
(4.5 mm), #2 (6 mm), #3 (9 mm), #4 (14 mm), #5 (19 mm)
and an adjustable attachment comb (4 - 18 mm) are also
optionally available as accessories.
Attaching/removing the attachment comb
The adjustment lever used to adjust the cutting
length must not be locked (Fig. 4
ⓑ
).
f Slide the locking switch (B) upwards
(Fig. 3
ⓐ
).
1. Slide the attachment comb on to the blade set in the
direction of the arrow until it reaches the limit stop (Fig.
5
ⓐ
).
2. Slide the attachment comb off the blade set in the
direction of the arrow (Fig. 5
ⓑ
).
Maintenance
Warning! Injuries and material damage due to
incorrect handling.
f Switch off the appliance before cleaning it or
performing any maintenance and disconnect it
from the mains.
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the
appliance.
f Only reconnect the appliance to the power
supply if it is completely dry.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appli-
ance and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil
recommended by the manufacturer.
Accessories and spare parts are available from
your dealer or our service centre.
f Remove the attachment comb (Fig. 5
ⓑ
) after every
use. Remove the hair clippings from the blade set with
the cleaning brush.
f If a thorough cleaning is required, the blade
set can be removed. See chapter
Changing
the blade set
.
f After cleaning the blade set, we recommend using
hygienic spray. It keeps all blade sets hygienically clean
and is effective against bacteria and viruses.
f Oil the blade set with the blade set oil (Fig. 6).
f We recommend that you clean and care for your blade
set during and after clipping with Blade Ice spray. The
Blade Ice spray ensures instant cooling, oiling and
cleaning of the blade set, while also protecting against
corrosion.
f Switch the appliance on briefly (approx. 10 seconds) to
ensure the oil film is evenly distributed.
f For a good and long-lasting cutting perfor-
mance, it is important to oil the blade set
frequently.
f If the cutting performance deteriorates after
long use despite regular cleaning and oiling,
the blade set should be replaced.
f Only wipe the appliance with a soft, slightly damp cloth.

Chat with your Moser Primat 1230-0053 manual using AI

Get instant AI answers from your Moser Primat 1230-0053 manual

Ask anything about the Moser Primat 1230-0053. Answers come from this manual, with the pages they are based on.

Primat 1230-0053 Maintenance Schedule

After every use
Clean blade set and remove hair clippings

Remove attachment comb. Use cleaning brush to remove hair from blade set. Wipe appliance with soft, slightly damp cloth.

Show in the manual (page 13)
Frequently / After use
Oil the blade set

Apply blade set oil to ensure good cutting performance. Switch on briefly (approx. 10 sec) to distribute oil evenly.

Show in the manual (page 13)
During and after use
Clean and cool blade with Blade Ice Spray

Use Blade Ice spray for instant cooling, oiling, cleaning, and corrosion protection of the blade set.

Show in the manual (page 13)
As needed
Replace worn blade set

If cutting performance deteriorates despite regular cleaning and oiling, replace the blade set.

Show in the manual (page 13)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Primat 1230-0053?

Yes No

Frequently Asked Questions

A

The standard cutting length without any attachment comb is approximately 0.7 millimeters. This setting provides a very close cut suitable for detailed work and fades.

Is this answer helpful?

A

No, this model is designed exclusively for cutting human hair, beard hair, and eyebrows. Using it on animals may damage the blades and void the warranty.

Is this answer helpful?

A

You can adjust the length while the device is on by sliding the locking switch down and moving the side lever to one of the six preset positions before sliding the lock back up.

Is this answer helpful?

A

No, never use the clipper near bathtubs, showers, or wet areas. Water exposure poses a severe electric shock hazard even when the unit is turned off.

Is this answer helpful?

A

If the blades pull hair, they are likely dirty or worn. Clean and oil them immediately. If the issue persists, the blades may need replacement due to wear.

Is this answer helpful?

A

For best performance, oil the blade set frequently, ideally during and after every use session to ensure smooth cutting and prevent rust.

Is this answer helpful?

A

The manual is included with the product. You can also request a PDF version from authorized service centers or check the documentation provided in the box.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Quiet oscillating armature motor reduces noise during operation
  • MultiClick lever allows instant cutting length changes from 0.7 to 3 mm
  • Durable construction designed for heavy commercial salon use
  • Easy blade removal facilitates thorough cleaning and maintenance
  • Compatible with a wide range of optional attachment combs
VS

Disadvantages

  • Cable length may require extension for some large workstation setups
  • Requires specific maintenance oils and sprays for optimal blade care
  • Heavy vibration if used continuously without cooling breaks
  • Initial setup requires reading manual to align blades correctly
  • Replacement parts must be ordered through authorized service centers
M: QW-35-FL

Product Specification

Type

Hair clipper

Power source

Corded

Cut lengths

6 cut lengths, 0.7-9mm

Cut width

1.81 inches

Package contents

Guard cap, cleaning brush, oil

M: QW-35-FL

Product Description

Mastering Precision with the Moser 1230-0053 Primat

The Moser 1230-0053 Primat in light gray stands as a testament to professional-grade grooming engineering. Designed specifically for commercial use, this hair clipper delivers consistent performance for barbers and stylists who demand reliability. Its sleek light gray casing not only looks professional but is built to withstand the rigors of daily salon operations. The device features a quiet oscillating armature motor that ensures smooth operation without excessive noise, creating a more comfortable environment for both the client and the operator.

One of the standout features of the Moser 1230-0053 Primat Manual is its versatile cutting length adjustment system. Users can effortlessly switch between lengths ranging from 0.7 mm to 3 mm using the MultiClick lever mechanism. This allows for precise fading and blending techniques directly during operation without needing to stop the machine. For those requiring longer cuts, the clipper supports various attachment combs, including optional sizes like 4.5 mm up to 19 mm, or an adjustable comb for custom lengths.

Maintenance is straightforward yet critical for longevity. The blade set can be easily removed for deep cleaning, ensuring hygiene standards are met after every use. The manufacturer recommends regular oiling and the use of specialized Blade Ice spray to cool and protect the blades from corrosion. Safety is paramount, with robust insulation and electromagnetic compatibility certifications ensuring the device meets strict EU standards. Whether you are trimming human hair, beards, or eyebrows, this tool offers the precision needed for high-quality results.

M: QW-35-FL

© Copyright 2026 Manual.ly