Manual.ly Logo

Monacor WALL-06T Manual

0.0 · 0 Ratings

PDF manual · 6 Pages

English

M: QW-35-FL
page

/ 6

Loading...
95a3b6157e23dc930e75a1f2b9c114b59e04 page 2
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
A-1891.99.02.06.2021
2
3
4
2
1
PA Wall Speakers
These instructions are intended for in-
stallers with specific knowledge in sound
reproduction using 100 V technology.
Please read the instructions carefully prior
to installation and keep them for later ref-
erence.
1 Applications
These speaker pairs are specially designed for
PA systems. Featuring a 2-way system, the
speakers offer excellent sound quality and
speech intelligibility. The speakers are provided
with a transformer for operation in 100 V sys-
tems, but they can also be directly connected
to a low-impedance amplifier output. A rotary
switch is used to match the connected load.
By means of their mounting bracket, the
speakers can be fastened to a wall or ceiling.
Due to their weatherproof housing (IP 65), the
speakers are also suited for outdoor applica-
tions.
2 Important Notes
The speakers correspond to all relevant direc-
tives of the EU and are therefore marked
with .
•
Protect the speakers against extreme tem-
peratures (admissible temperature range:
0 – 40 °C).
•
Never use aggressive detergents or chemicals
for cleaning.
•
No guarantee claims for the speakers and no
liability for any resulting personal damage
or material damage will be accepted if the
speakers are used for other purposes than
originally intended, if they are not correctly
installed, if they are overloaded or if they are
not repaired in an expert way.
If the speakers are to be put out of
operation definitively, take them to
a local recycling plant for a disposal
which is not harmful to the environ-
ment.
3 Installation
WARNING During operation, there is a haz-
ard of contact with a voltage
of up to 100 V at the speaker
cable. Installation must be made
by skilled personnel only.
Observe the load of the PA amplifier by the
speakers. An overload may damage the am-
plifier!
1) Before installing the speaker, switch off the
PA amplifier so that the speaker cable will
not carry any voltage!
2) Remove the plastic support (4) from the
metal bracket (3).Then use two screws to
fasten the support to the desired location
(e. g. wall or ceiling).
3) Fasten the metal bracket (3) to the plastic
support, using the two recessed head screws
of the bracket. Use the holes in the metal
bracket which are most suitable for the de-
sired speaker alignment.
4) Use the screws (2) to fasten the speaker (1)
to the metal bracket. Before tightening the
screws, connect the speaker and align it to
the desired sound zone.
5) Remove the connection cover.
6) Adjust the power rating for 100 V operation
on the rotary switch. For direct operation at
a low-impedance amplifier output, set the
switch to the position “8 Ω”.
CAUTION! Never use the position “8 Ω”
when the speaker is operated in a 100 V
system: The speaker and possibly also the
amplifier will be damaged.
7) Connect the cable to the terminals. Make
sure that all speakers have the same polarity
(e. g.
⊕
= red terminal).
8) Replace the connection cover.
Subject to technical modification.
English
Specifications WALL-04T/… WALL-05T/… WALL-06T/… WALL-08T/…
Power rating
100 V operation
8 Ω operation
16 / 8 / 4 / 2 W
30 W
16 / 8 / 4 / 2 W
40 W
32 / 16 / 8 / 4 W
50 W
50 / 25 / 12.5 / 6.25 W
60 W
Music power 60 W 80 W 100 W 120 W
Frequency range 90 – 20 000 Hz 80 – 20 000 Hz 70 – 20 000 Hz 35 – 20 000 Hz
SPL 87 dB (1 W/1 m) 89 dB (1 W/1 m) 90 dB (1 W/1 m) 90 dB (1 W/1 m)
Max. SPL 100 dB 104 dB 106 dB 106 dB
Speaker configuration
Bass-midrange speaker
Dome tweeter
10 cm (4”)
12 mm (½”)
13 cm (5”)
12 mm (½”)
16 cm (6”)
25 mm (1”)
20 cm (8”)
25 mm (1”)
Connection terminals
Dimensions (with bracket)
Width
Height
Depth
130 mm
197 mm
164 mm
163 mm
252 mm
203 mm
196 mm
303 mm
250 mm
245 mm
378 mm
306 mm
Weight 1.8 kg 2.6 kg 3.5 kg 5 kg
IP rating IP 65
Ambient temperature 0 – 40 °C
WALL- 04T ⁄ SW Order No. 0163560
WALL- 05T ⁄ SW Order No. 0163580
WALL- 06T ⁄ SW Order No. 0163600
WALL- 08T ⁄ SW Order No. 1000607
WALL- 04T ⁄ WS Order No. 0163570
WALL- 05T ⁄ WS Order No. 0163590
WALL- 06T ⁄ WS Order No. 0163610
WALL- 08T ⁄ WS Order No. 1000608

Chat with your Monacor WALL-06T manual using AI

Get instant AI answers from your Monacor WALL-06T manual

Ask anything about the Monacor WALL-06T. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend WALL-06T?

Yes No

Frequently Asked Questions

A

No, the operational temperature range is strictly between 0 and 40 degrees Celsius. Using the unit below 0 C may damage internal components and void the warranty.

Is this answer helpful?

A

In 100 V mode, the speaker uses an internal transformer for long-distance wiring in public address systems. In 8 Ω mode, it connects directly to low-impedance amplifiers for shorter runs and higher fidelity.

Is this answer helpful?

A

Yes, the IP 65 rating ensures it is fully protected against dust and water jets, making it ideal for outdoor installations exposed to rain and snow.

Is this answer helpful?

A

Use the rotary switch located behind the terminal cover to select the desired wattage for 100 V operation or set it to 8 Ω for direct amplifier connection.

Is this answer helpful?

A

Installation requires basic tools like screwdrivers and drills. However, only qualified personnel should perform the work due to electrical hazards.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • IP 65 rated for complete protection against dust and water jets
  • Versatile 100 V and 8 Ω operation modes for flexible installations
  • High speech intelligibility due to dedicated 2-way speaker system
  • Durable white housing suitable for harsh outdoor environments
  • Adjustable mounting bracket allows precise sound direction
VS

Disadvantages

  • Requires professional installation due to high voltage risks
  • Limited temperature range excludes extreme cold climates below 0 C
  • No warranty if installed incorrectly or overloaded by user
  • Rotary switch adjustment must be set carefully to avoid damage
  • Heavier weight compared to smaller models may require sturdy brackets
M: QW-35-FL

Product Specification

Principle

2-way

Tweeter

1x 1"/25.4mm

Woofer

1x 6"/152.4mm

Amplification

passive

Frequency range

70Hz-20kHz

Power handling

50W RMS, 100W Peak

Impedance

8Ω

Sensitivity

90dB

Max SPL

106dB

Dimensions

7.72x11.93x9.84 in (WxHxD)

Weight

7.72 lbs

M: QW-35-FL

Product Description

Monacor WALL-06T White: Professional Outdoor Sound Solutions

The Monacor WALL-06T white pair represents a pinnacle of engineering for public address systems requiring durability and clarity. Designed specifically for specialists, these wall-mounted speakers are ideal for both indoor corridors and outdoor environments where weather resistance is paramount. The sleek white finish allows them to blend seamlessly into various architectural settings while delivering robust audio performance.

These units feature a sophisticated two-way system comprising a 16 cm bass-midrange driver and a 25 mm dome tweeter. This configuration ensures high sound quality and exceptional speech intelligibility, making them perfect for announcements in busy areas or background music in public spaces. The built-in transformer enables flexible operation within 100 V line systems, allowing for long cable runs without significant power loss. Alternatively, users can switch the rotary selector to the 8 Ω position for direct connection to low-impedance amplifiers, offering versatility across different installation scenarios.

Durability is at the core of the WALL-06T design. With an IP 65 rating, the housing is completely dust-tight and protected against water jets from any direction. This makes the speakers suitable for harsh outdoor conditions, including rain and snow, without compromising internal components. The mounting bracket system facilitates easy installation on walls or ceilings, with adjustable angles to direct sound precisely where needed. Installation requires skilled personnel due to the presence of hazardous voltages up to 100 V during operation.

Key Features and Benefits

The Monacor WALL-06T stands out for its adaptability and reliability. Whether installed in a school, hospital, or commercial complex, these speakers provide consistent performance. The ability to adjust power levels via a rotary switch allows installers to optimize the load on the amplifier, preventing overloads and ensuring efficient energy use. The unit operates effectively within temperatures ranging from 0 to 40 degrees Celsius, covering most climatic conditions found in temperate zones.

Important Installation Notes

Safety is critical when installing these units. Always ensure the PA amplifier is switched off before connecting cables to avoid electric shock. Maintain strict polarity alignment across all connected speakers to prevent phase issues that could degrade sound quality. Regular cleaning should be performed using non-aggressive detergents to preserve the protective coating and IP rating. Improper handling or exposure to extreme conditions outside the specified range may void warranties and lead to equipment failure.

Product Highlights

  • Weatherproof construction for year-round outdoor use.
  • Dual-mode operation for 100 V lines or 8 Ω amplifiers.
  • High SPL output for clear audio coverage.
  • Robust metal bracket for secure wall or ceiling mounting.
  • EU compliant with CE marking for safety standards.
M: QW-35-FL

© Copyright 2026 Manual.ly