Manual.ly Logo

Mesto Ferrox Plus 3565P Manual

0.0 · 0 Ratings

PDF manual · 48 Pages

English

M: OA-GPT-54-NAN
page

/ 48

Loading...
9e4d5aea2f7a9d2a2ba8d93c383c7736f851 page a
10
Nach Gebrauch
D A CH
Beachten Sie die Hinweise im Kapitel „Sicherheit“.
Beachten Sie die Hinweise im Kapitel „Sicherheit“.
Verwenden Sie nur Ersatz- und Zubehörteile von MESTO (einige nden Sie im
Ersatzteilbeutel [3], Abb. 1a bzw. 1b).
Beachten Sie die gesetzlichen Unfallverhütungsvorschriften Ihres Landes und
überprüfen Sie das Gerät regelmäßig.
Sollte es keine speziellen Regeln geben, empfehlen wir alle 2 Jahre eine äußere
und alle 5 Jahre eine innere Prüfung durch einen Sachkundigen durchzuführen.
Gerne stellen wir Ihnen einen Prüfplan in deutsch oder englisch zur Verfügung.
Sammeln und entsorgen Sie die Restmenge nach geltenden Gesetzen, Vor-
schriften und Regeln. Achten Sie auf die Vorschriften des Mittelherstellers!
Reinigen Sie nach Gebrauch die Schutzausrüstung und sich selbst
1. Ziehen Sie den roten Knopf des Sicherheitsventils [12] so lange hoch, bis der Behälter
drucklos ist. (Abb. 4)
2. Verriegeln Sie den Pumpengriff [13]. (Abb. 5)
3. Schrauben Sie die Pumpe [2] aus dem Behälter [1]. (Abb. 6)
4. Entleeren und spülen Sie das Gerät mit klarem Wasser durch.
5. Wischen Sie das Gerät mit einem feuchten Tuch ab.
6. Zum Austrocknen und Lagern bewahren Sie Behälter und Pumpe getrennt in trockener,
vor Sonnenstrahlen geschützter und frostfreier Umgebung auf.
Wartung und Pege
Nach 50-maligem Gebrauch, mindestens einmal jährlich:
• Bauen Sie die Pumpe [2] auseinander und fetten Sie die Manschette [20]. (Abb. 16 - 17)
• Reinigen Sie die Düse [21] unter ießendem Wasser, ggf. mit einer Nadel. (Abb. 18)
• Nehmen Sie den Filter [22] zwischen Abstellventil [9] und Spritzleitung [4] heraus und
reinigen Sie ihn unter ießendem Wasser. (Abb. 19)
• Fetten Sie die O-Ringe [19] und [24] ein. (Abb. 17 bzw. 23)
Störungen
Störung Ursache Abhilfe
Im Gerät baut sich kein
Druck auf
Pumpe nicht festge-
schraubt.
Pumpe fest einschrauben
O-Ring [19] an der Pumpe
defekt.
O-Ring tauschen. (Abb. 21)
Manschette [20] defekt. Manschette tauschen.
(Abb. 21)

Chat with your Mesto Ferrox Plus 3565P manual using AI

Get instant AI answers from your Mesto Ferrox Plus 3565P manual

Ask anything about the Mesto Ferrox Plus 3565P. Answers come from this manual, with the pages they are based on.

Ferrox Plus 3565P Maintenance Schedule

Remind me when maintenance is due
Every 50 uses
Disassemble pump and grease diaphragm

After 50 uses or at least once a year, disassemble the pump and grease the diaphragm.

Show in the manual (page 10)
Every 50 uses
Clean nozzle

Clean the nozzle under running water, using a needle if required.

Show in the manual (page 10)
Every 50 uses
Clean filter

Remove the filter between the shut-off valve and spray line and clean it under running water.

Show in the manual (page 10)
Every 50 uses
Grease O-rings

Grease the O-rings on the pump and pressure bolt.

Show in the manual (page 10)
Every 2 years
External inspection by expert

Have the device examined externally by a competent professional every 2 years.

Show in the manual (page 10)
Every 5 years
Internal inspection by expert

Subject the device to an internal inspection by a competent professional every 5 years.

Show in the manual (page 10)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Ferrox Plus 3565P?

Yes No

Frequently Asked Questions

A

It is designed for formwork oils, thin mineral oils, and mildly alkaline construction chemicals. Some INOX versions also support neutral, solvent-free cleaners and low-viscosity solvent-free paints. Always check the product compatibility before filling.

Is this answer helpful?

A

The maximum spraying pressure is 6 bar. The pressure gauge should be monitored while pumping, and the safety valve will release excess pressure if the limit is exceeded. For best results, stay within the recommended working range.

Is this answer helpful?

A

Yes, but only in well-ventilated areas. The manual recommends outdoor use or use in spaces with good airflow, especially when working with technical liquids. Proper ventilation helps reduce exposure and improves safety.

Is this answer helpful?

A

Release all pressure first, then remove the pump, empty the tank, and rinse it with clean water. Wipe the unit with a damp cloth and store the tank and pump separately in a dry, frost-free, sun-protected place.

Is this answer helpful?

A

Common causes include a pump that is not tightened properly, a damaged O-ring, or a worn diaphragm. Tightening the pump or replacing the defective sealing parts usually restores normal function.

Is this answer helpful?

A

Hold the spray lance upward during the first spray cycle and operate the shut-off valve until only liquid, not air mixed with liquid, comes out. This helps prime the system and reduces unwanted dripping.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Durable build with a steel tank and practical carrying options for shoulder or back use.
  • Clear pressure control up to 6 bar helps deliver consistent spray performance.
  • Works with selected oils and mild construction chemicals, adding useful versatility.
  • Maintenance steps are straightforward and support long-term, reliable operation.
VS

Disadvantages

  • Not suitable for flammable liquids, solvents, ammonia-based products, or many corrosive substances.
  • Must be used upright and with attention to pressure limits, which reduces flexibility in use.
  • Requires regular cleaning and seal care to prevent clogs, leaks, and pressure loss.
  • Not intended for food-related use or for storing liquids long term.
M: OA-GPT-54-NAN

Product Specification

Tank capacity

1.59 gal

Operating pressure

max. 87.02 psi

Hose length

8.20 ft

Special features

Safety pressure valve

M: OA-GPT-54-NAN

Product Description

Mesto 3565 P Ferrox Plus Pressure Sprayer Manual

The Mesto 3565 P Ferrox Plus Pressure Sprayer is built for users who need reliable, controlled spraying in demanding work environments. Designed with a sturdy tank, a practical pressure gauge, and an easy-to-handle shut-off system, it suits tasks where precision and consistency matter more than speed alone. This makes it a strong fit for construction, maintenance, and professional cleaning applications.

The series is intended for formwork oils, thin mineral oils, and lightly alkaline construction chemicals up to pH 9. Certain INOX versions expand that range further, allowing use with neutral, solvent-free cleaners and low-viscosity paints. That flexibility is one of the main reasons this sprayer stands out: it is not a general-purpose garden tool, but a focused piece of equipment for compatible technical liquids.

One of the most useful details is the emphasis on pressure control. The unit operates up to 6 bar, with a clear gauge that helps users stay within the safe working range. Spray output varies with pressure, which gives the operator better control over coverage and flow. The sprayer is also made for shoulder or back carry, helping reduce fatigue during longer jobs.

The manual highlights safety, maintenance, and correct preparation as part of normal use. Before filling, the device must be depressurized; after use, it should be emptied, rinsed, and stored dry. Regular care such as cleaning the nozzle, checking the filter, and greasing seals helps keep performance stable. These steps may seem simple, but they are essential for extending service life and avoiding common faults like pressure loss or clogged spray paths.

For readers comparing professional sprayers, the Mesto 3565 P Ferrox Plus Pressure Sprayer offers a clear value proposition: durable construction, controlled spraying, and a maintenance routine that supports long-term use. It is best viewed as a dependable tool for compatible liquids, especially where safety and consistency are non-negotiable.

Notes

  • Use only suitable, non-aggressive liquids.
  • Keep the device upright during spraying.
  • Release all pressure before filling, cleaning, or storage.
  • Inspect seals, nozzle, and filter regularly for best results.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly