Manual.ly Logo

Makita Drill, Bit and Socket Wrench Set Manual

0.0 · 0 Ratings

PDF manual · 44 Pages

English

M: OA-GPT-54-NAN
page

/ 44

Loading...
3427d30e5845fa7ad564389e1147c2e198ac page 7
7
Bevel cutting (Fig. 7 & 8)
With the base tilted, you can make bevel cuts at any
angle between 0° and 45° (left or right). Loosen the
bolt on the bottom of the tool. Move the base so that
the bolt is positioned in the center of the cross-
shaped slot in the base. Tilt the base until the desired
bevel angle is obtained. The edge of the motor hous-
ing indicates the bevel angle. (See Fig. 8.) Then
tighten the bolt to secure the base.
Flush cutting (Fig. 9)
Loosen the bolt on the bottom of the tool and move
the base all the way back. Then tighten the bolt to
secure the base.
Cutouts
Cutouts can be made with either of two methods A or B.
A) Boring a starting hole:
For internal cutouts without a lead-in cut from an
edge, pre-drill a starting hole more than 12 mm in
diameter. Insert the blade into this hole to start
your cut. (Fig. 10)
B) Plunge cutting:
Your need not bore a starting hole or make a
lead-in cut if you carefully do as follows:
1. Tilt the tool up on the front edge of the base, with
the blade point positioned just above the work-
piece surface. (Fig. 11)
2. Apply pressure to the tool so that the front edge
of the base will not move when you switch on the
tool and gently lower the back end of the tool
slowly.
3. As the blade pierces the workpiece, slowly lower
the base of the tool down onto the workpiece
surface.
4. Complete the cut in the normal manner.
Finishing edges (Fig.12)
To trim edges or make dimensional adjustments, run
the blade lightly along the cut edges.
Metal cutting
Always use a suitable coolant (cutting oil) when cut-
ting metal. Failure to do so will cause significant
blade wear. The underside of the workpiece can be
greased instead of using a coolant.
Plastic base plate (Fig. 13)
Use the plastic base plate when cutting decorative
veneers, plastics, etc. It protects sensitive surfaces
from damage. To replace the base plate, remove the
four screws.
Anti-splintering devise (Fig. 14)
For splinter-free cuts, the anti-splintering device can
be used. Fit it into the base from below.
Guide rule (optional accessory) (Fig. 15)
When cutting widths of under 150 mm repeatedly,
use of the guide rule (rip fence) will assure fast,
clean, straight cuts. To install it, loosen the bolt on the
front of the base. Slip in the guide rule and secure the
bolt.
Circular guide (optional accessory) (Fig. 16)
Use of the circular guide insures clean, smooth cut-
ting of circles (radius; under 200 mm. Insert the pin
through the center hole and secure it with the
threaded knob. Move the base of the tool forward
fully. Then install the circular guide on the base in the
same manner as the guide rule (rip fence).
Dust extraction (Fig. 17, 18 & 19)
The vacuum head is recommended to perform clean
cutting operations. Install the plastic cover on the tool
by fitting it into the notches in the tool.
To attach the vacuum head on the tool, insert the
hook of the vacuum head into the hole in the base.
The vacuum head can be installed on either left or
right side of the base. Then connect a Makita vac-
uum cleaner to the vacuum head.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by
a Makita Authorized Service Center.

Chat with your Makita Drill, Bit and Socket Wrench Set manual using AI

Get instant AI answers from your Makita Drill, Bit and Socket Wrench Set manual

Ask anything about the Makita Drill, Bit and Socket Wrench Set. Answers come from this manual, with the pages they are based on.

Drill, Bit and Socket Wrench Set Maintenance Schedule

Occasionally
Lubricate the roller

Occasionally lubricate the roller to ensure smooth blade operation.

When cutting metal
Use coolant when cutting metal

Always use a suitable coolant or lubricate the workpiece underside when cutting metal to prevent significant blade wear.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend Drill, Bit and Socket Wrench Set?

Yes No

Frequently Asked Questions

A

Its biggest advantage is versatility. A 66-piece layout gives users many options for different drilling and fastening jobs, which helps reduce downtime and keeps the right tool close at hand.

Is this answer helpful?

A

Yes. The clear, practical layout makes it accessible for beginners, especially if they want one organized kit for common home repair and maintenance tasks. Basic tool familiarity is still helpful.

Is this answer helpful?

A

It is best for everyday maintenance, assembly work, home repairs, and general workshop tasks. The variety of pieces makes it useful when you need to switch between fasteners or drilling needs.

Is this answer helpful?

A

Organization helps you find the right piece quickly, avoids misplacing parts, and improves workflow. It also supports safer, more efficient use because each attachment is easier to identify.

Is this answer helpful?

A

Yes. The source strongly stresses safe handling, correct setup, and following instructions. The overall message is that good results depend on both the tool and proper use.

Is this answer helpful?

A

They should choose the correct piece for the task, keep the set clean and stored properly, and follow the recommended instructions. Good preparation improves both accuracy and durability.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Wide 66-piece assortment supports many common drilling and fastening tasks.
  • Makita’s practical design approach favors control, convenience, and dependable use.
  • Clear instructions help users work safely and choose the right piece faster.
  • Good option for keeping one compact kit ready for home or workshop jobs.
VS

Disadvantages

  • The set may include more pieces than casual users need for very simple tasks.
  • Benefits depend on storing and organizing the parts properly after use.
  • Users still need to match the correct bit or socket to each application.
  • Not ideal if you only want a single-purpose tool instead of a broader kit.
M: OA-GPT-54-NAN

Product Specification

Tool Holder

1/4" (0.25 in) Hex, Cylindrical Shank (Drill)

Scope of Delivery

without ratchet, incl. MAKPAC1, 66-piece accessory set, magnetic holder

M: OA-GPT-54-NAN

Product Description

Makita Drill/bit/socket wrench set, 66-piece Manual

The Makita Drill/bit/socket wrench set, 66-piece Manual is built around the kind of practical thinking that makes workshop jobs feel smoother and more controlled. Rather than focusing on flashy extras, it reflects a straightforward approach: give users the right tools, clear guidance, and enough flexibility to handle everyday fastening and drilling tasks with confidence.

What stands out most is the emphasis on precision and usability. Makita’s style is all about working efficiently without sacrificing control, and that idea carries through in the way the set is presented. A 66-piece assortment gives users a broad range of options for common jobs, from routine assembly work to more detailed maintenance tasks. For anyone who likes to stay prepared, that variety can make a real difference.

The manual-style presentation also suggests a strong focus on safe, correct use. That matters because tool performance is not only about power; it is also about handling, fit, and consistency. When bits and sockets are organized well, and when the user follows a clear method, the work becomes faster and more reliable. This is especially useful for home repairs, garage projects, and light professional use where switching between tasks happens often.

Another advantage is adaptability. A well-rounded Makita kit is designed to support different surfaces, fasteners, and project types without forcing you to hunt for missing parts. That versatility makes it easier to keep a single set nearby for general use. Combined with Makita’s reputation for practical design, the result is a kit that feels ready for real-world work instead of just sitting in storage.

Why it works well

The Makita Drill/bit/socket wrench set, 66-piece Manual appeals to users who want an organized, dependable, and flexible tool solution. It is the kind of set that supports better workflow: fewer interruptions, quicker access to the right piece, and more confidence when switching between jobs. If you value clean organization and everyday reliability, this set fits that mindset well.

Notes

  • Best suited for users who prefer a complete, ready-to-use kit.
  • Clear instructions and organized tools help reduce mistakes.
  • A practical choice for routine repairs and general maintenance.
  • Keep the set stored clean and dry for longer service life.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly