Manual.ly Logo

Magnat Signature 505 Manual

0.0 · 0 Ratings

PDF manual · 46 Pages

English

M: OA-GPT-54-NAN
page

/ 46

Loading...
d2b57e08f3f8999fe360778272cb3c47cd6f page 7
Dear MAGNAT Customer,
Congratulations on your ne new loudspeakers and thank you very much for choosing MAGNAT! You
have made an excellent choice. The high-quality speakers produced by MAGNAT are renowned all over
the world.
Please study the instructions and information below carefully before using your new loudspeakers.
FITTING THE FEET (SIGNATURE 507 AND SIGNATURE 505 ONLY)
The (2) feet included in the delivery package must be tted to the loudspeaker before use. To do this,
place the speakers on a clean, stable base with the bottom facing upwards. It is better not to remove
the protective bag until after tting has been completed so as to avoid damage to the surface.
Now t the two pre-assembled feet using the M6 screws provided, as shown in Fig. 1.
GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT SIGNATURE 500 LOUDSPEAKERS
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent
impairment of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths up
to 3 m and at least 4 mm² for lengths above 3 m.
Always turn off the amplier or receiver before connecting or disconnecting loudspeaker cables. Place
the loudspeakers in their planned positions and cut the cables to the right length. The cables for both
channels should always be exactly the same length.
Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than tinning
them with solder – insert them in the terminals and tighten the terminal screws rmly. (Fig. 2)
For good sound it is imperative that the cables must be connected in such a way that the speakers are
“in phase”. This means that the black negative terminals on the speakers (-) must be connected to the
negative (-) terminals on the amplier, the red positive (+) speaker terminals to the positive (+) amplier
terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a ridge
in the insulation.
Before switching on the system double-check all your connections and make sure that the terminal screws
are tight and that there are no short circuits caused by stray wire laments – this could cause serious
damage to your amplier!
THE MAGNAT SIGNATURE 500 LOUDSPEAKERS IN STEREO MODE
In the ideal conguration the speakers and the listening position should form an equilateral triangle. When
the left and right speakers are the same distance from the listening position their sound arrives at the
same time, resulting in a harmonious, natural music reproduction. (Fig. 3)
There should be a clear line of sight between the loudspeakers and the listening position. Any sound-
absorbing or reecting obstacles in the path will distort the sound. When you install the loudspeakers the
following distances should be maintained:
SIGNATURE 500 oorstanders: at least 20 cm away from the rear wall and at least 30 cm from the side
walls. This will prevent excessive emphasis of the bass range.
SIGNATURE 500 bookshelf speakers: shelf loudspeakers should also be as free-standing as possible,
the distance to the sides and rear to walls and items should be at least 10 cm, the tweeters should be
located at ear height.
Spikes (SIGNATURE 500 oorstanders): you should use the supplied spikes when setting the speakers
up. This isolates them from the supporting surface, preventing unpleasant resonance effects. You can
choose between metal and hard rubber spikes for the standing speakers. The spikes are screwed into
the threaded sleeves in the feet from below and tightened from above with the locking nut.
7

Chat with your Magnat Signature 505 manual using AI

Get instant AI answers from your Magnat Signature 505 manual

Ask anything about the Magnat Signature 505. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Signature 505?

Yes No

Frequently Asked Questions

A

Yes. Before use, install the included feet (2 pieces). Place the speaker with the bottom facing up on a clean, stable base. It is recommended to remove the protective bag after the feet are fitted to avoid damaging the surface. Use the provided M6 screws to attach the pre-assembled feet as shown in the setup illustrations.

Is this answer helpful?

A

The manual recommends at least 2.5 mm2 for cable lengths up to 3 m, and at least 4 mm2 for longer runs. Use quality speaker cables from an audio dealer. Keep both channels the same cable length and ensure connections are tight to avoid sound or safety issues.

Is this answer helpful?

A

Connect black (-) speaker terminals to black (-) amplifier terminals, and red (+) speaker terminals to red (+) amplifier terminals. Many speaker cables include a colored strip or ridge on one conductor to help you identify polarity. After connecting, double-check that terminals are secure and that no stray strands can short.

Is this answer helpful?

A

Aim for an equilateral triangle between the two speakers and your listening position. Keep a clear line of sight, and avoid strong reflective or absorptive obstacles between speakers and seat. Maintain placement spacing: at least 20 cm from the rear wall and at least 30 cm from the side walls, and keep tweeters at ear height.

Is this answer helpful?

A

Yes. The four screw terminals support conventional wiring and bi-wiring/bi-amping. The top terminals feed the tweeter and the bottom terminals feed the woofer. For bi-wiring/bi-amping, remove the factory-installed metal bridges that connect the terminals for standard 2-wire use, then follow the correct connection diagram.

Is this answer helpful?

A

Keep tone controls centered for linear operation. Turning bass and treble too far boosts energy to tweeters and woofers and can cause damage at high volume. Also watch for audible distortion and reduce volume immediately. Ensure your amplifier can deliver power appropriate for the speakers, since weak amps can distort earlier.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 3.5-way bass reflex design with wide frequency coverage (24-53,000 Hz) for detailed sound
  • Bi-wiring and bi-amping capable via four screw terminals and removable metal bridges
  • Sound-optimized placement guidance (20 cm rear, 30 cm sides) for controlled bass
  • Recommended speaker cable specs and clear in-phase polarity instructions
  • Includes feet and uses spikes for decoupling and reduced resonance
VS

Disadvantages

  • Requires careful setup: correct polarity, tight terminal connections, and strict spacing for best results
  • Tone controls must be kept moderate; boosting bass/treble at high volume can damage drivers
  • Can be risky with mismatched amplification: weak amps may distort earlier
  • Needs proper cable gauge and length matching to avoid performance loss
  • More configuration steps if using bi-wiring or bi-amping
M: OA-GPT-54-NAN

Product Specification

Type

Floorstanding speaker

Principle

3.5-way

Tweeter

1x 1.20"/30.5mm, 1x 0.70"/17.8mm

Midrange driver

1x 6.70"/170.2mm

Woofer

1x 6.70"/170.2mm

Frequency range

24Hz-53kHz

Power handling

170-300W

Impedance

4-8Ω

Sensitivity

92dB

Dimensions (WxHxD)

8.07x36.61x13.07in

Weight per piece

34.20lb

M: GO-GEM-FL-25

Product Description

Magnat Signature 505: High-Impact Stereo Sound with Setup-Friendly Design

If you want floorstanding speakers that deliver a balanced, room-filling presentation, the Magnat Signature 505 is built for that job. Part of the SIGNATURE 500 family, this 3.5-way bass reflex model combines a serious power capability with a tuning philosophy that rewards careful placement and correct wiring. For owners who want a smooth start, the guidance compiled in the Magnat Signature 505 Manual helps you get the most from the system without guesswork.

Clear imaging starts with placement

For best stereo results, the listening position should form an equilateral triangle with the left and right speakers. When both speakers are the same distance from your seat, timing differences are reduced and the soundstage stays natural. Also aim for a visible line of sight between speakers and listening area, since reflective or sound-absorbing obstacles can blur detail.

Placement matters. Keep the floorstanders at least 20 cm from the rear wall and at least 30 cm from the side walls to avoid excessive bass emphasis. For stability and resonance control, the Signature 505 is delivered with feet and uses optional spikes. This decouples the cabinet from the supporting surface, helping prevent unwanted vibration effects.

Hooking up correctly makes the difference

Use quality speaker cable from an audio dealer. For cable runs up to 3 m, the manual recommends at least 2.5 mm2; for longer lengths, at least 4 mm2. Always switch off your amplifier or receiver until all connections are secured. Strip about 10-15 mm, twist the ends, insert into the terminals, and tighten firmly.

Most important: connect in phase. Black (-) speaker terminals must go to black (-) amplifier terminals, and red (+) to red (+). Double-check for any stray wire that could create a short circuit.

Bi-wiring and bi-amping ready

The Signature 505 features four screw terminals, with the top pair assigned to the tweeter and the bottom pair to the woofer. Factory metal bridges connect positive and negative terminals for conventional 2-wire use. Remove those bridges for bi-wiring or bi-amping, where separate cables (and a second power amplifier for bi-amping) can further refine the presentation.

Specs at a glance

3.5-way bass reflex floorstander, 4-8 ohm impedance, 24-53,000 Hz frequency response, 170/300 W power handling, 92 dB efficiency, and dimensions of 286 x 970 x 332 mm.

Key results

  • Proper in-phase wiring reduces imaging problems and protects the amplifier from wiring mistakes.
  • Room spacing (20 cm rear, 30 cm sides) helps keep bass controlled rather than overwhelming.
  • Spikes and proper feet installation support lower vibration and cleaner cabinet behavior.
  • Bi-wiring and bi-amping compatibility is built in, using the four-terminal layout.

Notes

  • Keep tone controls centered for best linear performance; extreme boosting at high volume can risk damage.
  • If tweeters drop out at low or medium levels, have the system checked for inaudible high-frequency issues.
  • Clean the cabinet with a mild household cleaner only; avoid furniture polish.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly