Manual.ly Logo

Mafell ZH 320 Ec Manual

0.0 · 0 Ratings

PDF manual · 78 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 78

Loading...
fd47f837a247a9844870bd871c6ece7a02cc page b
-11-
Mit dem Ausschalten wird gleichzeitig die
automatische Bremse wirksam. Damit verkürzt sich
die Auslaufzeit der Maschine auf ca. 1 – 3 Sekunden.
5.3 Spantiefeneinstellung
Die Spanabnahme kann zwischen 0 und 3 mm
eingestellt werden. Dies erfolgt mit dem Handgriff 5
(Abb. 4) für die Spantiefeneinstellung, wobei die
eingestellte Hobeltiefe auf der Skala 6 abgelesen
werden kann.
Im normalen Betrieb sollte die Spanabnahme auf ca.
2 mm beschränkt bleiben. Die maximale
Spanabnahme sollte zur Vermeidung einer
Überlastung des Motors nur in extremen Fällen
ausgenutzt werden.
5.4 Arbeitshinweise
Der Zimmereihobel liegt infolge seiner
ausgewogenen Gewichtsverteilung gut in der Hand.
Er lässt sich mit den Handgriffen 1 und 4 (Abb. 4)
führen.
Zum Hobeln wird die Maschine mit der vorderen
Auflagefläche so auf das Werkstück aufgelegt, dass
die Hobelwelle nicht zum Eingriff kommt. Nach dem
Einschalten wird der Zimmereihobel, sobald die
Hobelwelle ihre volle Drehzahl erreicht hat, mit
gleichmäßigem Druck über das Holz geführt. Ein
gleichmäßiger Vorschub ergibt ein sauberes
Hobelbild und schont die Maschine.
Beim Überlasten des Zimmereihobels fällt die
Drehzahl der Hobelwelle ab. Es muss gewartet
werden, bis die Hobelwelle ihre volle Drehzahl wieder
erreicht hat. Danach kann mit verringertem Vorschub
weitergearbeitet werden.
Bei Arbeiten mit voller Hobelbreite wird der Hebel mit
der Führungsrolle 7 nach unten geschwenkt und mit
dem Rändelknopf 8 festgespannt. Dadurch hat der
Hobel eine seitliche Führung.
Nach dem Hobeln Maschine durch Loslassen des
Schalters sofort ausschalten und nicht mit laufender
Hobelwelle absetzen. Beim Zurückstellen der
Spanabnahme auf 0 kann der Hobel auch bei
ungünstiger Lage der Messer auf einer ebenen
Fläche abgestellt werden, ohne die Unterlage zu
beschädigen.
5.5 Späneauswurf
Der Zimmereihobel ist so gestaltet, dass beim Hobeln
mit sachgerechter Vorschubgeschwindigkeit und voll
ausgenutzter Hobelbreite ein einwandfreier
Spanauswurf sichergestellt ist. Dabei werden die
Späne seitlich ausgeworfen, so dass eine
Behinderung der Sicht auf das Werkstück vermieden
wird.
6 Wartung und Instandhaltung
Gefahr
Bei allen Wartungsarbeiten den
Netzstecker ziehen.
MAFELL-Maschinen sind wartungsarm konstruiert.
Die eingesetzten Kugellager sind auf Lebenszeit
geschmiert. Nach längerer Betriebszeit empfehlen
wir, die Maschine einer autorisierten MAFELL-
Kundendienstwerkstatt zur Durchsicht zu übergeben.
Für alle Schmierstellen nur unser Spezialfett, Bestell -
Nr. 049040 (1 kg - Dose), verwenden.
6.1 Werkzeug
Die auf der Maschine benutzte Hobelwelle,
Spannbacken, Messerträger und Messer sollten
regelmäßig entharzt werden, da ein sauberes
Werkzeug die Schnittqualität verbessert. Das
Entharzen erfolgt durch 24-stündiges Einlegen der
Spannbacken, Messerträger und Wendemesser in
Petroleum oder handelsübliche Entharzungsmittel.
Aluminiumwerkzeuge dürfen nur
mit Lösungsmitteln, welche das
Aluminium nicht angreifen, entharzt
werden.
6.2 Lagerung
Wird die Maschine längere Zeit nicht verwendet, ist
sie sorgfältig zu reinigen. Blanke Metallteile mit einem
Rostschutzmittel einsprühen.

Chat with your Mafell ZH 320 Ec manual using AI

Get instant AI answers from your Mafell ZH 320 Ec manual

Ask anything about the Mafell ZH 320 Ec. Answers come from this manual, with the pages they are based on.

ZH 320 Ec Maintenance Schedule

Regularly
Clean tool and remove resin

Deresinify planing shaft, spacer blocks, blade carriers, and blades by soaking in petroleum or commercial agent for 24 hours to improve cutting quality.

Show in the manual (page 11)
After long use
Service machine inspection

Hand the machine over to an authorized MAFELL customer service shop for inspection after a longer period of operation.

Show in the manual (page 11)
Long-term storage
Clean and protect metal parts

Carefully clean the machine and spray bright metal parts with a rust inhibitor if not used for a long time.

Show in the manual (page 11)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend ZH 320 Ec?

Yes No

Frequently Asked Questions

A

The machine operates with an input power of 2700 watts on 230 volts. This high power rating allows it to maintain speed under heavy load while cutting dense solid wood effectively.

Is this answer helpful?

A

While optional for very short tasks, using an external extraction system is strongly recommended. You must ensure the air velocity is at least 20 meters per second to protect your health from wood dust.

Is this answer helpful?

A

Always pull the power plug before changing blades. Unscrew the lateral cover and release the clamping screws. Always reverse both blades or fit new ones to maintain balance.

Is this answer helpful?

A

No. This plane is exclusively designed for solid wood. Planing over metal parts like nails can damage the blades and cause dangerous ejection of metal fragments.

Is this answer helpful?

A

Operators must wear ear protection to prevent hearing damage and a dust mask to avoid inhaling harmful wood dust during extended periods of use.

Is this answer helpful?

A

Use the handle located on the side of the machine to set the depth. The scale allows you to read the exact planing depth between zero and three millimeters.

Is this answer helpful?

A

It is only recommended to use original Mafell spare parts and accessories. Using non-original parts may violate the warranty terms and affect machine safety.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • High power 2700 watt motor handles tough wood
  • Automatic brake stops the shaft in about three seconds
  • Electronic speed control prevents overload damage
  • Adjustable depth of cut offers precision control
  • Built for low maintenance with life-greased bearings
VS

Disadvantages

  • Heavy weight of 14 kilograms may cause fatigue
  • Requires dust extraction system for health safety
  • Intended strictly for solid wood, not composites or metal
  • Switch does not lock on, requiring constant pressure
  • Safety instructions must be read carefully before use
M: qwen/qwen3.5-flash-20260224

Product Specification

Power

2700 W

No-load speed

8500 rpm

Planer width

12.60 in

Cutting depth

0-0.12 in

Special features

Dust extraction, auxiliary handle, constant electronic control

Weight

30.86 lbs

Package contents

Reversible cutter

M: qwen/qwen3.5-flash-20260224

Product Description

Elevate Your Carpentry with the Mafell ZH 320 Ec Electric Plane

Professional woodworking demands tools that combine raw power with sophisticated safety features. The Mafell ZH 320 Ec stands as a premier choice for carpenters who require reliable performance on solid wood projects. This heavy-duty electric plane utilizes a universal motor that is suppressed for radio and television interference. With a rated power intake of 2700 watts, it maintains consistent speed under load, ensuring high-quality surface finishes every time.

The unit features a substantial planing width of 320 millimeters, allowing users to cover large areas efficiently. It weighs 14 kilograms without the power cable, which provides the necessary mass for smooth operation during planing. The depth of cut is adjustable between zero and three millimeters via a side handle, but standard operation should remain near two millimeters to avoid stalling the motor.

Safety Features and Electronic Controls

Safety mechanisms are integral to the design of this machine. An automatic braking system activates as soon as the trigger is released, drastically cutting the run-out time to approximately three seconds. Electronic circuits also manage the speed, returning the motor to safe levels during overload situations. When troubleshooting issues or adjusting settings, please consult the official Mafell ZH 320 Ec Electric Plane Manual to ensure all steps are followed correctly.

Wood dust generation is inevitable during planing. Health regulations suggest using a dust extraction hose connected to the 75 millimeter intake port. Operators must always wear ear protection and a dust mask while running the machine. These precautions protect against hearing loss and respiratory issues associated with prolonged wood dust exposure.

Maintenance and Operational Care

Mafell designs these tools for durability with minimal service requirements. The bearings are pre-lubricated for life, reducing the need for frequent intervention. Regular maintenance involves keeping the guide rails clean of resin. To ensure original performance, only use genuine replacement parts listed in the spare parts documentation. Reversible blades allow for extended usage before replacement is necessary, making it cost-effective for workshops.

When not in use, store the plane in a dry location. Always remove foreign objects like nails from the wood before planing. The switch requires continuous pressure, and there is no lock-on feature, ensuring the machine stops when hands are removed. Following these guidelines ensures the longevity of the tool.

Conclusion

This electric plane represents a significant investment for serious carpenters. It balances power with precision.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly