Manual.ly Logo

Mafell NFU 50 Manual

0.0 · 0 Ratings

PDF manual · 198 Pages

English

M: QW-35-FL
page

/ 198

Loading...
e664033f49d219a324701b541daa75da816b page 20
-32-
Danger
The warning light 25 (Fig. 1)
indicates the rotation of the tool by
means of an “orange” signal. The
warning light 25 switches off when
the tool is stationary. Now you can
pull the machine back into the
starting position. As long as the
signal glows, you may not lift the
machine off the workpiece or pull it
back.
5.11 Working with position indicator (for KSS-
guiding device and F-rail)
Use position indicator 29 (Fig. 3) to
align the KSS-guiding device. The
position indicator shows the right
side of the milling cutter, set the
position indicator to the same angle
as the machine. The position
indicator is enclosed with the
machine.
Follow the procedure below:
• Fasten the position indicator 29 with the wing
bolts 9 (Fig. 3).
• Set the position indicator 29 to the same angle
as the machine tilt. You can also determine the
position of position indicator 29 by means of an
auxiliary milling groove in the tool.
• The angle scaling refers to the right side of the
milling head.
• Set the required milling depth and machine the
workpiece.
5.12 Working with the lateral stop in combination
with KSS-guiding device
The lateral stop 50 (Fig. 4) is used to work parallel to
an already existing groove. Lock the stop in the guide
groove of the KSS-rail. The lateral stop is preset to
approximately 625 mm, fine adjustment at the stop is
possible.
Different rafter spacings can be set via the markings
X and Y at the face edge stop:
X = 625 mm with 60 mm milling head
Y = 600 mm with 46 mm milling head
Follow the procedure below:
• Unfasten the locking screw 53 with the wrench
AF 5 that is kept on the position indicator.
• Turn the adjusting screw 54 in the
corresponding direction.
• Retighten the locking screw 53.
6 Service and maintenance
Danger
Pull the power plug during all
service work.
MAFELL machines are designed to be low in
maintenance.
The ball bearings used are greased for life. When the
machine has been in operation for a longer period of
time, we recommend to hand the machine in at an
authorised MAFELL customer service shop for
inspection.
Only use our special grease, order No. 049040 (1 kg
tin) for all greasing points.
Check the braking effect of your machine at regular
intervals. If the braking effect worsens, always
contact your MAFELL after-sales service to have the
braking system serviced.
In order to check the safety functions, the machine
must be handed in at a MAFELL service workshop for
inspection at the latest after 3 years of use.
6.1 Storage
If the machine is not used for a longer period of time,
it has to be carefully cleaned. Spray bright metal parts
with a rust inhibitor.
Store the machine only in dry rooms and protect it
from the effects of weather.
6.2 Tools
The milling heads used on the machine should be
regularly deresinified, as clean tools improve the
cutting quality.
Deresinify them by placing them in petroleum or a
commercially available deresinification agent for 24
hours.

Chat with your Mafell NFU 50 manual using AI

Get instant AI answers from your Mafell NFU 50 manual

Ask anything about the Mafell NFU 50. Answers come from this manual, with the pages they are based on.

NFU 50 Maintenance Schedule

Remind me when maintenance is due
Every 3 years
Safety function inspection

The machine must be inspected by a MAFELL service workshop at the latest every 3 years to check safety functions.

Show in the manual (page 32)
Before every use
Check mobile lower guard function

Verify the mobile lower guard closes freely and immediately. Check spring function. Do not use if damaged or sticky.

Show in the manual (page 26)
Regularly
Clean adjusting devices and guides

Regularly clean the machine, especially adjusting devices and guides, to ensure safety.

Show in the manual (page 26)
Regularly
Check tool clamping

Inspect the tightness of the tool clamping at regular intervals. Ensure torque is at least 20 Nm.

Show in the manual (page 27)
Regularly
Der resin milling heads

Soak milling heads in petroleum or deresinification agent for 24 hours to improve cutting quality.

Show in the manual (page 32)
After longer operation
Professional inspection

Hand the machine in at an authorized MAFELL service shop for inspection after a longer period of operation.

Show in the manual (page 32)
Regularly
Check braking effect

Check the braking effect at regular intervals. If it worsens, contact MAFELL service for brake system maintenance.

Show in the manual (page 32)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend NFU 50?

Yes No

Frequently Asked Questions

A

No. Plunge milling and reverse milling are not permitted due to the risk of serious recoil and injury. The tool must only be guided into the material as specified in the operating manual.

Is this answer helpful?

A

The milling depth is adjustable from 0 to 50 mm at a 0 degree angle. It is continuously variable for precise control over the cut depth.

Is this answer helpful?

A

While not strictly mandatory for operation, dust extraction is highly recommended. Health hazards such as wood dust require an M-suction device to prevent respiratory issues during prolonged use.

Is this answer helpful?

A

The machine should be handed in to an authorized service workshop at the latest after three years to check safety functions. Brake effect should be checked regularly as well.

Is this answer helpful?

A

No. Only tools recommended by Mafell and manufactured according to standard EN 847-1 are permitted. Using unauthorized tools voids the warranty and compromises safety.

Is this answer helpful?

A

If the motor stops due to overload, the electronic system prevents automatic restarting. You must switch the machine off and on again, then continue milling at a reduced forward speed.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Adjustable milling depth of 0 to 50 mm allows for versatile cutting options
  • Integrated retractable safety guards protect the operator from debris
  • Compatible with external dust extraction systems for better workshop air quality
  • Automatic speed adjustment maintains consistency under varying load conditions
  • Sealed ball bearings reduce the need for frequent lubrication and maintenance
VS

Disadvantages

  • Plunge milling and reverse milling operations are strictly forbidden for safety
  • Noise emissions reach 88 decibels requiring mandatory hearing protection gear
  • Tool changes require strict adherence to unplugging procedures and specific tools
  • Unauthorized parts invalidate the manufacturer warranty and safety compliance
  • The heavy base plate may limit portability and require stable surface support
M: QW-35-FL

Product Specification

Type

Dowel Router

Power

2300 W

No-load Speed

5900 RPM

Cutter Diameter

6.42 in

Max Cut Depth

0-1.97 in

Cut Width

2.36 in

Bevel Angle

0-45 deg

Arbor Size

1.18 in

Features

Additional Handle, Parallel Fence, Length Fence, Dust Extraction

Weight

20.72 lb

M: QW-35-FL

Product Description

Introduction

The Mafell NFU 50 stands out as a premium tool for woodworking professionals. This powerful router is designed for precision groove cutting and cross-cut milling applications. When you consult the comprehensive Mafell NFU 50 Electric Flat Dowel Router Manual, you gain access to detailed safety and operational guidelines essential for safe usage. The motor delivers an impressive 2300 watts of power, ensuring efficient performance on various wood materials. Safety is paramount, with features like retractable guards and a warning light that signals active rotation.

Why Choose This Machine

Professionals value the robust construction and low maintenance design. The machine includes a parallel stop and a roller edge guide for straight cuts. Dust extraction is vital, and this model supports external suction systems. The included KSS guiding device ensures accuracy during operation. Users must adhere strictly to the instructions found in the Mafell NFU 50 Electric Flat Dowel Router Manual. Ignoring safety protocols can lead to serious injury or equipment damage. Regular maintenance ensures continued performance and reliability.

User Experience

Handling the NFU 50 requires two hands on the designated grips. Switching on involves a specific lock mechanism to prevent accidental activation. The tool spindle speed adjusts automatically to maintain performance. While the machine is powerful, it requires care when changing cutters. Always unplug the device before maintenance tasks. The included accessories cover basic setup needs. Ultimately, this system provides reliability for serious carpentry tasks. Regular inspection of sliding parts and brake function is recommended to maintain peak safety levels during use.

The operational versatility allows for depth locking and repeater stops without needing to measure twice. This saves time on production runs where identical grooves are required. The tilting milling unit enables complex work including angled notches. Despite the features, the weight remains manageable at 7.7 kilograms. Noise levels are noted at approximately 88 decibels. The machine is designed for EU voltage standards, making it ideal for European workshops. Proper ventilation and dust collection are recommended for health.

Maintenance Requirements

Maintaining the machine involves regular cleaning of chips and resin on cutter heads. Proper storage prevents corrosion of metal parts. Bearing lubrication is sealed for life, reducing servicing needs. If the braking effect worsens, professional service is required. Following the guidelines in the Mafell NFU 50 Electric Flat Dowel Router Manual ensures longevity. Adherence to the maintenance schedule keeps the machine functioning well. This quality control distinguishes professional grade equipment from consumer models in the industry.

M: QW-35-FL

© Copyright 2026 Manual.ly