Manual.ly Logo

Mafell MT 55 cc Manual

0.0 · 0 Ratings

PDF manual · 98 Pages

English

M: OA-GPT-5-NAN
page

/ 98

Loading...
df76466ed7bffccba151d7ebb290fac3a94e page d
-13-
Verwenden Sie ein geeignetes Sägeblatt (siehe
Kapitel 4.3).
Wechseln Sie das Sägeblatt (siehe Kapitel 4.4).
Das Diamantsägeblatt ist für
Faserzementplatten entwickelt
worden. Die Diamant bestückten
Zähne sind empfindlicher als die
Zähne des HM – Sägeblattes.
Deshalb arbeiten Sie mit einer
Führungsschiene.
5.10 Arbeiten mit Führungsschienen
Um eine genauere Führung zu erreichen, stellen
Sie mit den beiden Stellrädern 21 (Abb.2 und 4)
das Führungsspiel ein.
Mit der Tauchsäge kann mit den im Sonderzubehör
erhältlichen Führungsschienen gearbeitet werden.
Zusätzlich können auch einige am Markt erhältliche
Schienen verwendet werden.
Dazu lösen Sie die Schrauben und entfernen
die Einlage 24 (Abb.2).
5.11 Arbeiten mit dem Positionsanzeiger MT-PA
Piktogramme hierzu siehe Seite 4.
6 Wartung und Instandhaltung
Gefahr
Bei allen Wartungsarbeiten den
Netzstecker ziehen.
MAFELL-Maschinen sind wartungsarm konstruiert.
Die eingesetzten Kugellager sind auf Lebenszeit
geschmiert. Nach längerer Betriebszeit empfehlen
wir, die Maschine einer autorisierten MAFELL-
Kundendienstwerkstatt zur Durchsicht zu übergeben.
Für alle Schmierstellen nur unser Spezialfett, Bestell -
Nr. 049040 (1 kg - Dose), verwenden.
6.1 Lagerung
Wird die Maschine längere Zeit nicht verwendet, ist
sie sorgfältig zu reinigen. Blanke Metallteile mit einem
Rostschutzmittel einsprühen.
7 Störungsbeseitigung
Gefahr
Die Ermittlung der Ursachen von vorliegenden Störungen und deren
Beseitigung erfordern stets erhöhte Aufmerksamkeit und Vorsicht. Vorher
Netzstecker ziehen!
Im Folgenden sind einige der häufigsten Störungen und ihre Ursachen aufgeführt. Bei weiteren Störungen
wenden Sie sich bitte an Ihren Händler oder direkt an den MAFELL-Kundendienst.
Störung Ursache Beseitigung
Keine Netzspannung vorhanden Spannungsversorgung
kontrollieren
Netzsicherung defekt Sicherung ersetzen
Maschine lässt sich nicht
einschalten
Kohlebürsten abgenützt Maschine in die MAFELL-
Kundendienstwerkstatt bringen
Netzausfall Netzseitige Vorsicherungen
kontrollieren
Maschine bleibt während des
Schneidens stehen
Überlastung der Maschine Vorschubgeschwindigkeit
verringern

Chat with your Mafell MT 55 cc manual using AI

Get instant AI answers from your Mafell MT 55 cc manual

Ask anything about the Mafell MT 55 cc. Answers come from this manual, with the pages they are based on.

MT 55 cc Maintenance Schedule

After long periods of operation
Send machine for inspection

Hand the machine in at an authorized MAFELL customer service shop for inspection after a longer period of time.

Show in the manual (page 13)
For extended storage
Clean and protect metal parts

If not used for a long time, clean carefully and spray bright metal parts with a rust inhibitor.

Show in the manual (page 13)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend MT 55 cc?

Yes No

Frequently Asked Questions

A

The MT55cc is intended for longitudinal and cross cuts in solid wood, chipboard, core board and MDF. With the appropriate diamond blade it can also cut fibre cement board. It is not designed for cutting metals.

Is this answer helpful?

A

The cutting depth is adjustable up to 57 mm. The saw accepts blades with a nominal diameter up to 162 mm and a 20 mm arbor; the standard blade supplied is a 162 mm carbide-tipped blade.

Is this answer helpful?

A

The saw features stepless electronic speed control with a setting wheel, allowing blade speeds from 3,600 to 6,250 rpm for matching material and blade type; the electronics also provide jerk-free acceleration and overload regulation.

Is this answer helpful?

A

Yes. It has a 35 mm dust port for external extraction and comes with fixed upper and lower guards, a large base plate, dual handles, an electronic brake and a safety lock-off lever. Use extraction and PPE to reduce dust and noise risks.

Is this answer helpful?

A

Mafell offers guide rails (various lengths), parallel guide fences, diamond blades for fibre cement, position indicators (MT-PA), anti-kickback stops and multiple TCT blade types to improve accuracy and finish.

Is this answer helpful?

A

Disconnect the mains, fold down the guard cover using the push-button and locking lever, lock the spindle, loosen the flange screw with the provided Allen key, remove the front clamping flange and lift the blade forward. Fit the new blade observing rotation direction, reassemble and secure the guard.

Is this answer helpful?

A

MAFELL machines are low-maintenance; bearings are grease-packed for life. Regular cleaning of adjustment mechanisms and guides is important. Use only Mafell-approved spare parts and their special grease at designated lubrication points; have long-used units serviced by an authorized Mafell workshop.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Powerful 1,400 W motor with electronic speed control for smooth acceleration and overload protection.
  • Compact and portable (4.5 kg) with a protective case for easy transport and site use.
  • Precise depth (0–57 mm in 1 mm steps) and bevel adjustment (-1° to 48°) for versatile cutting.
  • Supplied with a carbide-tipped 162 mm blade and compatible with a wide range of Mafell accessories.
  • Robust safety features: fixed guards, large base plate, electronic brake and dust-extraction port.
VS

Disadvantages

  • High noise emission during machining—hearing protection is essential.
  • Relatively high sound power level (up to 104 dB A) may limit some indoor uses without mitigation.
  • Some accessories (e.g., guide rails, diamond blades) sold separately, adding to total cost.
  • Not suitable for cutting metals—only intended for wood, panels and fibre cement with diamond blade.
  • Parallel guide not included on all MidiMAX variants; check model contents before purchase.
M: OA-GPT-5-NAN

Product Specification

Type

Plunge Saw

Power

1400W

Saw Blade Diameter

6.38 in

Cutting Capacity

2.24 in (cutting depth at 0 degrees), 1.57 in (cutting depth at 45 degrees bevel)

Blade Bevel

1°/​48°

Arbor Size

0.79 in Bore

Features

Speed Control, Dust Extraction, Bevel Function

Weight

9.92 lb

Scope of Delivery

Case (T-Max)

M: OA-GPT-54-NAN

Product Description

Mafell MT55cc MidiMAX Electric Plunge Saw incl. Case Manual

The Mafell MT55cc MidiMAX Electric Plunge Saw is a compact, high-performance plunge-cut circular saw designed for precision woodworking and professional trade use. Built around a 1,400 W universal motor with electronic speed control, the MT55cc delivers smooth acceleration, overload protection and stepless blade-speed adjustment between 3,600 and 6,250 rpm. With a maximum cutting depth of 57 mm and a lightweight 4.5 kg body, it balances portability and cutting capability for longitudinal, cross and bevel cuts in solid wood, panels and laminate materials. The MidiMAX variants include a robust carrying case ensuring safe transport and storage.

Engineered safety and ergonomics are central to the MT55cc. Fixed upper and lower guards, a large base plate, comfortable handles and an electronic brake minimize downtime and risk. The saw features a lock-off safety lever and a non-latching trigger for controlled operation, plus a riving knife-compatible setup and a 35 mm dust-extraction port for connecting to external extraction systems. The machine’s typical hand–arm vibration rating is under 2.5 m/s², while measured noise emissions are high during machining, so hearing protection is recommended.

The MT55cc is supplied with a carbide-tipped Ø162 mm, 48-tooth saw blade, service tool, parallel guide (except on some MidiMAX models), a position indicator (on selected item numbers) and a comprehensive manual that details setup, blade selection, blade change, plunge cutting techniques, bevel angle adjustment (-1° to 48°), scoring with guide rails and diamond blade use for fibre cement. The tool’s precise depth adjustment (1 mm increments) and accessories such as guide rails, diamond blades and varying TCT blade tooth counts make it adaptable for fine cabinetry, joinery and sitework.

Maintenance is straightforward: life-lubricated bearings reduce service needs, while regular cleaning of guides and adjustment parts keeps the tool operating safely and accurately. Use only approved Mafell replacement parts and accessories to preserve warranty and machine safety. The manual highlights residual risks—blade contact, kickback, ejected blade fragments and dust exposure—and prescribes PPE and correct procedures for plunge starts, feeding, clamping panels, and dealing with blade stalls.

In short, the Mafell MT55cc MidiMAX is a purpose-built plunge saw for professionals seeking precise, portable cutting power with strong safety features and a flexible accessory ecosystem. For those requiring consistent, clean cuts—especially when combined with Mafell guide rails and scoring techniques—this saw is a reliable workshop and on-site solution.

Notes

  • Always read and follow the included Mafell MT55cc MidiMAX Electric Plunge Saw incl. Case Manual safety and operating instructions before use.
  • Use appropriate PPE: hearing and dust protection, and ensure dust extraction when cutting for extended periods.
  • Only use blades rated for the saw’s rpm and approved accessories to maintain safety and warranty.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly