Lupine SL X Manual
PDF manual · 15 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your Lupine SL X manual using AI
Get instant AI answers from your Lupine SL X manual
Ask anything about the Lupine SL X. Answers come from this manual, with the pages they are based on.
SL X Maintenance Schedule
Do not use a strong water jet or heavy detergent to clean the lamp.
If the light source or one of the LEDs is defective, replace the entire headlight. Replacement or repair must be done by Lupine only.
Ask a Question
Do you recommend SL X?
Yes NoFrequently Asked Questions
The SL X is highly water-resistant with an IP68 rating, designed to withstand severe weather and wet conditions. However, it is not intended for underwater use or diving operations; prolonged submersion or use as a dive light is not recommended.
Is this answer helpful?
Mount the CNC holder near the stem, passing the M4 bolt through the clamp with the O-ring sequence, then secure to the lamphead with the supplied allen keys (2Nm and max 1Nm where specified). Position the lamp centered and close to the stem; the mount can be fitted on either side depending on stem width.
Is this answer helpful?
The SL X operates on 6–12 V systems. Ensure your drive unit supplies sufficient voltage and that the light input is enabled in the controller software. Some systems (notably some Bosch units) may not provide enough power—verify compatibility at www.lupine.de or with your dealer.
Is this answer helpful?
A built-in brightness sensor automatically switches between daytime running light and low beam; the wired remote mounted near the grip shows green for low beam, blue for high beam and off for daytime running light or power-off. Manual switching to high beam is possible when low beam is active.
Is this answer helpful?
Calibrate only with the lamp mounted and outdoors, away from artificial light or reflective surfaces. Incorrect calibration can significantly impair lamp behavior. Successful calibration is confirmed by a short flash of the daytime running light.
Is this answer helpful?
If any LED or the light source fails, the entire headlight must be replaced or returned to Lupine for service. Always carry a backup light as failure can be sudden; consult your dealer to ensure light input is activated and compatibility is correct.
Is this answer helpful?
Yes. The housing can become hot—keep it away from combustible materials and never look directly into the beam. Do not use focusing optical devices on the beam. Children over 8 may use the device only under supervision.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Compact CNC-machined aluminium body (45x84x48mm) offering durable, lightweight construction.
- High output up to 1800 lumens with flexible modes: daytime running light, low beam, high beam.
- IP68 water resistance and robust sealing for extreme weather use (not for diving).
- Wired remote with clear LED status indicators and programmable settings including sensor delays.
- Precision mount allows side choice and centered alignment for stable, repeatable positioning.
Disadvantages
- Entire lamp must be replaced or returned to Lupine if any LED fails—no individual LED repair.
- Not suitable for underwater use despite IP68 rating; avoid strong water jets and harsh cleaners.
- Some e-bike drive units (e.g., certain Bosch systems) may not supply enough power or compatibility.
- Heat generation requires keeping the housing away from combustible materials during use.
- Sensor calibration is sensitive and must be done outdoors; improper calibration can impair function.
Product Specification
Type
Front light
Colors
black
Max. light output
1800 lm
Light mode
Continuous light
Power supply
36V (E-bike)
Mounting
Bracket
Dimensions
1.81x3.35x1.89in
Weight
0.38 lb
Special features
waterproof, dustproof, parking light, remote control, exclusively for e-bikes, StVZO compliant
Product Description
Lupine SL X Frontlicht Manual
The Lupine SL X Frontlicht is a compact, high-performance bicycle headlight designed for demanding conditions. Crafted from CNC-machined 6061-T6 aluminium, the SL X houses nine Osram automotive LEDs behind a Fresnel lens reflector system, delivering up to 1800 lumens peak and configurable output modes for daytime running light, low beam and high beam. With IP68 water resistance and a robust build, it resists harsh weather and rough rides, though it is not intended for underwater use.
Installation is straightforward: the machined mount clamps to stems 400–1200 mm height, with the M4 bolt and O-ring sequence ensuring secure fitment. The holder can be mounted on either side to center the lamp. Tightening uses included allen keys, and alignment guidance places the lighthead centered and near the stem to produce a light cone whose half-height at 5 m equals the outlet height.
Operation is intuitive via a wired remote mounted near the grip. The remote indicates status with colors: green for low beam, blue for high beam and off when the lamp is switched off or running-light mode is active. A brightness sensor enables automatic switching between daytime running light and low beam; manual override through the remote allows switching to high beam when darkness permits. Programmable options include delays (5s or 16s), manual mode presets, and restoring factory settings.
Sensor calibration must be done outdoors with the lamp mounted and free from reflective surfaces or artificial light. Incorrect calibration can impair functionality. Power compatibility is important: the SL X operates reliably on 6–12 V systems but some e-bike drive units (notably certain Bosch systems) may not supply sufficient power; check compatibility before purchase. In case of LED failure the entire lamp must be replaced or serviced by Lupine.
The SL X balances lightweight, compact dimensions (45 x 84 x 48 mm) with configurable power modes (daytime running 2.5 W, low beam 7.5–9 W, high beam 18–22 W) to suit both commuter and performance needs. Built-in safety warnings emphasize avoiding direct eye exposure, keeping the lamp clear of combustible materials due to heat generation, and carrying a backup light in case of failure.
Notes:
- Not a dive lamp: IP68 rated but not for underwater use.
- Calibration only outdoors and when mounted.
- Repair or LED replacement only by Lupine.
- Check e-bike drive compatibility and ensure light input is enabled in controller software.
Search for 67,706 Manuals online
Type-in Brand or Model