Manual.ly Logo

Lupine SL AF 7 StVZO Manual

0.0 · 0 Ratings

PDF manual · 17 Pages

English

M: OA-GPT-5-NAN
page

/ 17

Loading...
dba746ff0f1eac01ea134204f9b8a7325cc7 page 7
Deutsch
12
SL AF StVZO
13
SL AF StVZO
Fehlerbehebung
Fehler
Lampe lässt sich nicht ein-
schalten.
Power LEDs leuchten nicht.
Die Leuchtzeiten sind zu gering.
Der Smartcore Akku zeigt auch
nach dem Laden nur 20% an.
Der Sensor reagiert nicht.
Ursache
Tiefentladener Akku
Akku nicht oder fehlerhaft
am Scheinwerfer angesteckt
LED-Einsatz ist defekt
Der Akku ist leer
Der Akku ist alt
Sehr tiefe Temperaturen
Das Ladegerät ist defekt
Die Anzeige wurde zurück
gesetzt
Der Sensor liegt nicht frei
Behebung
Akku laden
Alle Steckerkontakte
überprüfen
Austauschen bzw. Lupine
kontaktieren
Laden
Austauschen
Akku warm halten
Ladegerät austauschen
Akku mit der Lampe
vollständig entleeren und
wieder aufladen
Den Sensor von Dreck,
Schmutz usw. befreien
Pflege, Lagerung und Laden
Warnung! Mit diesem Ladegerät dürfen nur wiederaufladbare
Li-Ionen-Akkus aufgeladen werden. Es ist NICHT zum Laden von
Ni-MH-Akkus geeignet!
Keine Trockenbatterien verwenden! – Explosionsgefahr!
Dieses Ladegerät darf NUR vom Hersteller geöffnet werden!
Pflege und Lagerung
Lampe:
Bei Verschmutzung, reinigen Sie den Scheinwerfer äußerlich mit warmem Wasser und etwas Spülmittel.
Achtung! Der SL Lampenkopf darf nicht geöffnet werden da damit die Wasserdichtigkeit und jeglicher
Garantieanpruch verloren geht. Bevor sie einen Fehler selbst beheben nehmen sie Kontakt mit unserem
Service auf.
Akku:
Vor längerem Nichtgebrauch laden Sie den Akku voll und lagern Sie diesen an einem möglichst kühlen,
trockenen Ort, wie z.B. Keller etc.
Laden des Akkus:
Stecken Sie das beiliegende Ladegerät Wiesel in Ihre Steckdose.
1. Verbinden Sie das Ladegerät mit dem Akku
2. Der Ladevorgang startet automatisch - die LED leuchtet rot
Ist der Ladevorgang beendet und der Akku voll leuchtet die LED grün.
Die Lampe reagiert nicht auf den
Sender.
Lampenkopf und Sender sind
nicht miteinander gebunden.
Siehe Kapitel Funksender.
Knopfzelle leer oder falsch
herum eingelegt.

Chat with your Lupine SL AF 7 StVZO manual using AI

Get instant AI answers from your Lupine SL AF 7 StVZO manual

Ask anything about the Lupine SL AF 7 StVZO. Answers come from this manual, with the pages they are based on.

SL AF 7 StVZO Maintenance Schedule

After use
Clean the lamp

Clean the lamp and cables externally with warm water and mild detergent after use in dirty areas. Do not use strong water jets or heavy detergents.

Before long storage
Charge and store battery

Fully charge the battery before long periods of non-use and store it in a cool, dry place.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend SL AF 7 StVZO?

Yes No

Frequently Asked Questions

A

Position the lamp centered on the handlebar, close the quick-release bracket until secure, and use the supplied Velcro strap to mount the SmartCore battery. For 50 mm stems use the optional stem kit. Fine-tune the quick-release lever for a tight fit.

Is this answer helpful?

A

The integrated sensor automatically switches between daytime running light and low beam, with configurable delay (3 or 16 seconds). Sensor calibration must be done outdoors with the lamp mounted; it stores the measured brightness threshold to determine switching behavior.

Is this answer helpful?

A

Two SmartCore batteries are typical: 3.5 Ah (SL AF 4) and 6.9 Ah (SL AF 7). Typical runtimes vary by mode—examples include multi-hour runtimes at lower power and several hours at higher outputs; SL AF 7 offers around 5.5 hours in moderate use configurations. Actual runtime depends on selected mode and temperature.

Is this answer helpful?

A

Activate lamp receive mode by holding the lamp button until it lights nine times; the lamp is receptive for ~30 seconds. Then press the remote’s large button for about five seconds until it lights blue. The remote mounts next to the grip for ergonomic control and uses a CR2032 cell.

Is this answer helpful?

A

Clean the exterior with warm water and mild detergent. Do not open the lamp head, as this voids waterproofing and warranty. Charge and store batteries in a cool, dry place, and fully charge before long-term storage.

Is this answer helpful?

A

Check battery charge and connector contacts first. If deeply discharged, charge fully. Ensure the sensor is unobstructed. For defective LED modules, charger issues, or persistent problems contact Lupine support; do not open or repair the lamp yourself.

Is this answer helpful?

A

The SL AF 7 is built to meet StVZO requirements with appropriate beam shaping and includes StVZO K1552 approval references. Local regulations vary by country, so verify national rules for bicycle lighting before use.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Sensor-driven auto-switching between daytime running light and low beam for hands-free adaptation to ambient light.
  • High output (up to 16 W) with StVZO-compliant beam shaping and efficient dual-aspheric lens optics.
  • Rugged IP68 construction and CNC-machined aluminum housing for durability in harsh conditions.
  • SmartCore battery options (3.5 Ah / 6.9 Ah) with audible and visual capacity indicators for clear runtime management.
  • Bluetooth remote control allows on-the-fly high beam and dimming adjustments without removing hands from the bars.
VS

Disadvantages

  • Lamp head can become hot during operation; requires airflow to sustain maximum output.
  • Not intended for underwater use despite IP68 rating; do not submerge for diving.
  • Battery not covered by standard two-year warranty; replacement cost possible over time.
  • Sensor calibration must be done outdoors and improperly calibrating can limit functionality.
  • Internal repairs not user-serviceable—LED or battery failures require manufacturer service or replacement.
M: OA-GPT-5-NAN

Product Specification

Type

Front light

Colors

black

Max. light output

1,300 lm

Max. light duration

6 h

Min. light duration

3 h

Light mode

Continuous light (2 levels)

Power supply

Battery (6,900 mAh)

Mounting

Bracket

Dimensions

3.11x1.61x1.89in (Front light), 2.32x1.97x1.89in (Battery)

Weight

0.79 lb

Special features

waterproof, StVZO compliant

M: OA-GPT-54-NAN

Product Description

Lupine SL AF 7 StVZO Front Light Manual

The Lupine SL AF 7 StVZO front light is a high-performance bike lamp engineered for reliable daytime and night riding. Combining a sensor-driven automatic mode with manual controls and Bluetooth remote operation, the SL AF 7 delivers configurable beam patterns, long runtimes, and rugged weather resistance. It’s built from CNC-machined aluminum and uses efficient LED optics to meet StVZO legal requirements while maximizing visible output and battery economy.

Key features and how it feels on the bike

Mounted centrally on the handlebar with a quick-release bracket and a Velcro-mounted SmartCore battery, the SL AF 7 is straightforward to install and secure. The lamp offers multiple power presets—high beam, low beam, dimmed low beam and daytime running light—ranging from 1.5 W (DRL) up to 16 W (high beam). A built-in brightness sensor automatically switches between day and night modes; you can fine-tune delay and calibration settings or use the Bluetooth remote for instant high-beam or dimming commands without taking your hands off the bars.

The SmartCore battery family (3.5 Ah and 6.9 Ah options) provides clear capacity feedback through a five-LED indicator with audible confirmation. Charging is simple with Lupine’s Wiesel charger; the lamp and battery are IP68-rated for robust wet-weather use (not for diving). Thermal management reduces output without damage when cooling airflow is limited, and the lamp’s housing can run warm under heavy use.

Practical use and maintenance

Routine cleaning requires only warm water and mild detergent; the lamp head must not be opened to preserve waterproofing and warranty. Troubleshooting guidance covers common issues—deep discharge, poor contacts, sensor occlusion, and pairing problems with the Bluetooth remote. Lupine recommends carrying a backup light because, as with any electronic device, unexpected failures can occur.

Notes

  • Complies with StVZO and includes StVZO-specific beam shaping (DRL supported by slight low beam).
  • Bluetooth remote pairs in a timed receive window; the remote mounts near the grip for ergonomic control.
  • Warranty covers two years for components (battery excluded).
  • Not suitable for underwater use despite IP68 rating.

Pros and cons are listed below, followed by an FAQ to help riders quickly assess capabilities and common questions.

M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly