Manual.ly Logo

Lupine C14 Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: OA-GPT-5-NAN
page

/ 2

Loading...
0394cc940937efd8479ab450e6c28174f157 page 1
C14
Lupine Lighting Systems GmbH
Im Zwiesel 9
D - 92318 Neumarkt
Germany
Mehr Informationen unter www.lupine.de
EG Konformitätserklärung: www.lupine.de/ce/
Assembly:
- Remove saddle clamp / seat post
- Position the C14 on the seat tube
- Attach the seat tube again
- Adjust the C14 and mount it with
5 - 7Nm Max. (allen key size 4)
- Install the cable along the frame to
the drive unit, using the enclosed
cable guides.
Note: Pay attention to the polarity
(red +, black -)
Operation:
You can turn the light on and off
manually by pushing the button at
the light.
C14
M4 screw
Button
Reference axis
(parallel to road)
Road
15 - 20°

Chat with your Lupine C14 manual using AI

Get instant AI answers from your Lupine C14 manual

Ask anything about the Lupine C14. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend C14?

Yes No

Frequently Asked Questions

A

The C14 operates on a 6–12 V supply and draws approximately 0.6–0.8 W. It can be powered from a bicycle or e-bike electrical system that meets these voltage requirements.

Is this answer helpful?

A

Yes. It can be connected to an e-bike battery if the electrical system ensures at least two hours of lighting after motor cutoff or if the drive motor can temporarily act as a generator to supply the light.

Is this answer helpful?

A

Remove the saddle clamp or seatpost, position the C14 on the seat tube, reinstall the seatpost, align the light, and tighten the M4 screw with a 4 mm Allen key to 5–7 Nm for secure mounting.

Is this answer helpful?

A

The red lens must be vertically oriented and unobstructed. Recommended alignment is 15–20° relative to the road reference axis. Ensure nothing blocks the light to maintain visibility and compliance.

Is this answer helpful?

A

The housing is anodized 6061-T6 aluminum. The unit is rated IP68 for water/dust protection and IK09 for impact resistance, making it durable for varied riding conditions.

Is this answer helpful?

A

The C14 comes with an 80 cm cable. Observe polarity during installation: red is positive (+) and black is negative (−). Use the included cable guides for neat routing.

Is this answer helpful?

A

Yes. Clamp diameter options include 31.8 mm, 34.9 mm, 35.6 mm, and 36.4 mm to fit a wide range of seat tube dimensions.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Compact, lightweight (35 g) aluminum body for durability without added mass.
  • IP68 and IK09 rated for high water and impact protection.
  • Low power draw (0.6–0.8 W) across 6–12 V, suitable for battery or e-bike systems.
  • Multiple clamp diameter options ensure compatibility with various seat tubes.
  • Simple on/off push-button and easy installation with supplied cable guides.
VS

Disadvantages

  • Fixed cable length (80 cm) may require additional routing or extensions on some frames.
  • Requires correct polarity connection (red +, black −); incorrect wiring may cause failure.
  • No specified flashing modes—basic on/off operation may lack advanced visibility patterns.
  • Mount must be aligned vertically (15–20°) and remain unobstructed for legal compliance.
  • Torque requirement (5–7 Nm) demands careful tightening to avoid under- or over-torquing.
M: OA-GPT-5-NAN

Product Specification

Type

Taillight

Colors

black

Max. light output

45 lm

Light source

14x COB LED

Light mode

Continuous light

Power supply

6-12V (E-Bike)

Weight

0.08 lb

Special features

waterproof, exclusively for e-bikes, StVZO compliant

M: OA-GPT-54-NAN

Product Description

Lupine C14 Rear Light — Reliable, Compact, High-Visibility Rear Light

The Lupine C14 Rear Light is a compact, high-performance bicycle taillight designed for reliable visibility on road and e-bike applications. Constructed from anodized 6061-T6 aluminum and rated IP68/IK09, this light balances rugged durability with lightweight design (35 g). Its COB LED delivers a steady, bright red output while consuming only 0.6–0.8 W and operating across a 6–12 V range. The C14 mounts cleanly to the seat tube with several clamp diameter options (31.8, 34.9, 35.6, 36.4 mm) and secures with an M4 screw at 5–7 Nm, offering a flush fit and stable alignment.

Installation is straightforward: remove the saddle clamp or seatpost, position the C14 on the seat tube, reinstall the seatpost, align the light vertically (recommended 15–20° relative to the road reference axis), and tighten. Route the included 80 cm cable along the frame using the supplied guides and observe polarity (red +, black −). For e-bikes the lamp can be powered from the drive battery if the system guarantees at least two hours of lighting supply after motor cutoff or if the motor can act as a temporary generator.

Operation is simple: an integrated push button toggles the light on and off. The red lens must remain unobstructed and vertically aligned to meet legal requirements and ensure maximum visibility. The C14’s compact footprint and variety of clamp sizes make it suitable for many frames, while its robust IP68 sealing protects against water and dust intrusion.

Whether used as a dedicated rear safety light on traditional bikes or integrated with an e-bike’s electrical system, the Lupine C14 prioritizes dependable illumination, sturdy build quality, and unobtrusive mounting.

Notes

  • Ensure correct polarity when connecting to a power source (red +, black −).
  • Maintain a vertical, unobstructed orientation; recommended mounting angle is 15–20° from the road reference axis.
  • Tighten mounting screw to 5–7 Nm using a 4 mm Allen key.
  • Cable length: 80 cm; plan routing accordingly.
  • Approved designation: K 1660.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly