LD Systems Deep2 1600 Manual
PDF manual · 64 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your LD Systems Deep2 1600 manual using AI
Get instant AI answers from your LD Systems Deep2 1600 manual
Ask anything about the LD Systems Deep2 1600. Answers come from this manual, with the pages they are based on.
Ask a Question
Do you recommend Deep2 1600?
Yes NoFrequently Asked Questions
The Deep2 1600 provides substantial professional power, with bridge-mode output rated at 1600 W into 4 Ω and strong stereo per-channel ratings suitable for driving full-range speaker systems with high headroom.
Is this answer helpful?
It includes protection against DC offset, overheating, short circuits and overcurrent; a Protect LED indicates when protection circuitry is active. Protection also engages automatically for a short interval on power-up.
Is this answer helpful?
The rear panel has XLR/TRS combi inputs, XLR link outputs for daisy-chaining, and speaker outputs using Speakon and binding-post terminals for secure high-power connections.
Is this answer helpful?
Select Bridge on the mode switch, feed the signal to channel A input and use channel A gain only; set channel B gain to minimum. Use the correct Speakon/binding-post bridge wiring as specified to avoid damage.
Is this answer helpful?
Yes, but you must adapt wiring: either bridge pin 1 and pin 3 or leave pin 3 unconnected depending on cable type. Balanced XLR cables are strongly recommended to reduce hum and interference.
Is this answer helpful?
The amplifier uses a high-efficiency two-speed fan. Allow adequate airflow around the unit, avoid enclosing it near heat sources, and ensure rack spacing to prevent overheating and fan strain.
Is this answer helpful?
Retain proof of purchase and contact Adam Hall or the authorized dealer where you bought the product. The limited warranty covers defects under normal use for the period specified by the manufacturer.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- High bridged power (1600 W @ 4 Ω) suitable for demanding professional use.
- Class H design with low THD (<0.1%) and wide frequency response (20 Hz–20 kHz).
- Comprehensive protection: DC, thermal, short-circuit and overcurrent safeguards.
- Professional I/O: XLR/TRS combi inputs, XLR link outputs, Speakon and binding posts.
- Dual-speed fan cooling and clear front-panel indicators for real-time monitoring.
Disadvantages
- Requires careful cabling and correct pin wiring when using unbalanced sources to avoid hum or damage.
- Bridge mode requires specific wiring and single-channel input control (channel B off).
- Heavy and rack-sized; less suitable for ultra-compact setups.
- Fans introduce potential noise and require ventilation space.
- Technical servicing should be performed only by qualified personnel; user repairs not supported.
Product Specification
Channels
2
Power 8Ω
450W, 1380W (bridged)
Power 4Ω
670W, 1600W (bridged)
Power 2Ω
800W
Dimensions
19.02x3.46x13.78in (WxHxD)
Weight
35.05lb
Product Description
LD Systems Deep2 1600 — Powerful, Reliable Power Amplifier
The LD Systems Deep2 1600 is a professional Class H power amplifier engineered for demanding live sound, installation, and touring applications. With a bridged output of 1600 W (4 Ω bridge) and robust per-channel power in stereo, the Deep2 1600 delivers high headroom, low distortion (<0.1% THD) and a wide frequency response (20 Hz–20 kHz) to reproduce clean, dynamic audio across full-range loudspeaker systems. Built with a focus on reliability, the unit includes protection circuits for DC, overtemperature, short circuit and overcurrent conditions, ensuring safe operation under heavy loads.
The front panel gives intuitive real-time feedback: multi-segment signal LEDs, a LIMIT indicator for clipping protection, and a PROTECT LED that signals the amplifier’s safety circuitry. Dual gain controls let you fine-tune channel levels, while an initial 3-second protect interval safeguards the amp during power-up. The rear panel provides professional connectivity: XLR/TRS combi inputs, XLR link outputs for daisy-chaining, and Speakon plus binding-post speaker outputs. A ground-lift switch helps resolve hum issues, and a stereo/bridge selector lets you combine channels for higher output when needed.
Designed for practical rigging and reliability, the Deep2 1600 uses a high-efficiency dual-speed fan cooling system and robust connectors suitable for road use. Input sensitivity and impedance are standardized (0.775 V, >20 kΩ) for compatibility with mixers and signal processors. The amp emphasizes proper cabling and grounding: balanced XLR cables are recommended to minimize noise and hum, and correct speaker wiring and gauge are advised to reduce power loss and preserve damping factor.
Users benefit from Adam Hall’s warranty and safety-conscious documentation: the product includes guidance on preventive measures, disposal (WEEE), and battery recycling. Clear manufacturer notes outline limitations and recommended servicing by qualified technicians only.
Whether used in stereo to drive two zones or bridged for maximum single-channel output, the LD Systems Deep2 1600 is aimed at professionals who need dependable power, clear indicators, flexible connectivity, and built-in protections for sustained high-performance operation.
Notes
- Use balanced XLR cabling whenever possible and check pin wiring for unbalanced sources.
- In bridge mode, use input and gain control for channel A only; set channel B gain to minimum.
- Observe ventilation and keep distance from heat sources; the amplifier has an active fan.
- Follow local regulations for disposal (WEEE) and battery recycling.
- For warranty service, retain proof of purchase and contact the authorized dealer or Adam Hall support.
Search for 67,706 Manuals online
Type-in Brand or Model