Manual.ly Logo

Lapp Mobility Mobility Dock Manual

5.0 · 2 Ratings

PDF manual · 1 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 1

Loading...
91d57731465939a29d5bf99a225158fd4ba6 page 1
TECHNICAL DATA
Charging power 2.3 kW
Nominal voltage range 230V AC
Nominal current 10 A *)
Frequency 50 Hz
Residual current circuit breaker (RCD) 30 mA AC 6 mA DC
Protection class I
Operating temperature -25 °C to +45 °C
Storage temperature -40°C to +85°C
IP degree of protection IP44
Can be connected to CEE 7/3 Typ F
*) Only for France and Finland: if the charging cycle can exceed 2 hours, the
max. rated current to be set on the vehicle is 8 A.
TRANSPORT AND STORAGE
WARNING An unsecured, inadequately secured or improperly
stored mobility dock can slip when braking or changing direction or
injure the occupants in an accident.
• Never transport the Mobility Dock unsecured.
• Never transport the Mobility Dock in the passenger compartment (e.g. on
or in front of the seats)
Dirt, moisture and damage to the Mobility Dock endanger safe opera-
tion. Risk of serious or fatal injury from electric shock or fi re.
• Store the Mobility Dock dry, clean and protected from chemical vapours,
e.g. in the boot.
• Store the Mobility Dock carefully so that its casing and mains plug (A) are
protected against damages during transport.
MAINTENANCE AND CARE
Disconnect the Mobility Dock from the vehicle and the mains before clean-
ing. Clean only with a slightly damp cloth. Do not use aggressive cleaning
agents.
DISPOSAL
The crossed-out wheeled bin logo requires the separate collection of
waste electric and electronic equipment (WEEE). Such equipment may
contain dangerous and hazardous substances. These tools must be
returned to a designated collection point for the recycling of WEEE and must
not be disposed as unsorted municipal waste. By doing so, you will help to
conserve resources and protect the environment. Contact your local
authorities for more information.
IMPORTANT SAFETY INSTRUCTIONS
Read all the instructions before using this product! Save instructions
for future reference.
WARNING RISK OF FIRE OR ELECTRIC SHOCK
Insu cient quality of the socket outlet may cause electric shock and/
o r fi r e .
• The Mobility Dock may only be operated from a socket suitable for this
purpose. The connection must comply with the applicable national norms
and standards.
• The Mobility Dock may only be used in properly earthed networks.
• Unsupervised charging is only permitted at an industrial or household
socket-outlet that has been checked by an electrician.
• Unsupervised charging at a household socket-outlet that has not been
checked by an electrician may lead to a fi re inside the house.
• Unauthorized people, particularly children, must not be able to access the
charging cable or vehicle during unsupervised charging.
WARNING RISK OF EXPLOSION
The Mobility Dock can generate sparks that can ignite gases and
dusts.
• Do not use the Mobility Dock in rooms with an increased risk of explosion.
WARNING RISK OF ELECTRIC SHOCK, SHORT CIRCUIT, FIRE, EXPLO-
SION
Use of a damaged charging cable, a defective or faulty plug/coupling
or a defective or faulty Mobility Dock as well as improper use or
failure to observe the safety instructions may result in short circuit,
electric shock, burns, explosion or fi re.
• Visually check all components for damage. Do not use damaged compo-
nents!
• Only connect the Mobility Dock to correctly connected, undamaged wall
sockets that have been installed and tested by a qualifi ed electrician.
• Check connectors and mobility dock for visible damage (cracks, broken
parts) and dirt before use. Do not use cables with damaged plugs or dirty
housing.
• Mobility Dock must not be opened. Dangerous voltages can discharge in
the housing, which can lead to an electric shock or death.
• No repairs or modifi cations may be carried out on the Mobility Dock (e.g.
replacement of the plug).
• Never immerse the Mobility Dock and accessories in water.
• Keep the Mobility Dock away from sources of dust and chemical emissions
(e.g. oil mist, soldering fumes, chemical vapours).
• Do not drop the Mobility Dock.
• Avoid strong bending or twisting of the cable.
• Avoid strong tensile stress on the cable.
• If the plugged-in Mobility Dock or the power socket is damaged: Block the
danger zone, switch o the power at the fuse and only then disconnect. Con-
sult a qualifi ed electrician on how to proceed.
WARNING RISK OF FIRE OR ELECTRIC SHOCK
Incorrect use of the Mobility Dock may result in electric shock.
• Do not touch the contacts of the plug connections.
• Do not insert any objects into the plug connections.
• Protect all contacts against moisture.
• Only operate the Mobility Dock vertically suspended and supported on a wall
socket to avoid pulling on the wall socket (see fi g. 2). Heavy loads can damage
the Mobility Dock and/or the power socket.
• Do not plug the Mobility Dock into the socket until the charging plug is en-
gaged in the type 2 outlet (C). Otherwise the wall socket may be damaged.
• Do not use the Mobility Dock for anything other than its intended use (for
example, do not use it with power sockets that are near to the ground).
INTENDED USE
The Mobility Dock is a Mode 2 emergency charger for occasional, portable use.
Permanent use only in a safe, motionless and vertical position. Operation only
on mechanically and electrically suitable, wall-mounted sockets (see fi g. 2,
step5)!
SYMBOLS
Protective conductor not
switched
Not suitable for IT-net
Minimum ambient temper-
ature
Do not use just any type of
extension cord!
Do not use Mobility Dock
and charging cables that
are damaged anywhere on
the housing, connector or
cable!
Do not use travel adapt-
ers!
OPERATING INSTRUCTIONS EN
MOBILITY DOCK
(A) Mains plug
(E) Wall support
(C) Type 2 outlet
OPERATION
Charging
1. Insert the vehicle coupling into the vehicle inlet
2. Insert the charging plug into the type 2 outlet (C) until it clicks into place (B).
3. Unlock the wall support (E) with the knob (D) and fold it out in the direction of
the arrow until it stops.
4. Insert the mains plug (A) into a suitable wall socket so that the housing hangs
downwards. The Mobility Dock performs a self-test.
5. Turn the wall support until the Mobility Dock is supported in the vertical
position.
WARNING If the Mobility Dock is not supported, there is a risk of fi re
due to damage to the socket. Only use Mobility Dock if the wall support is
long enough to support it!
6. The Mobility Dock communicates with the vehicle and releases the charge.
End charging
1. End charging via the vehicle (LED lights up permanently green)
WARNING Risk of electric shock and fi re. Charging must be completed
before unplugging the Mobility Dock!
2. Unplug the Mobility Dock (A) from the wall socket
3. Unlock (D) the wall support (E) and bring it into the starting position
4. If necessary, unlock the charging plug with the orange lever (B) and unplug it
(see fi g. 3)
5. Unplug the vehicle coupling from the vehicle
6. Stow the Mobility Dock and cable securely in the boot (see ‘Transport and
storage’).
STATUS DISPLAY
LED Light sequence System status
–– permanently o not in socket
green permanently on Self test OK - Vehicle connected - Standby
green Flashing Charging
blue Flashing Reduced charging (e.g. at high temperature)
yellow/
green
Flashing
Vehicle connected *) WARNING STATUS
DISPLAY
yellow Flashing
Charging *) WARNING STATUS DISPLAY
white permanently on
Self test OK - Vehicle not connected: Disconnect Mo-
bility Dock from socket and connect to vehicle fi rst
white Flashing
*) WARNING STATUS DISPLAY Self test OK
- Vehicle not connected: Disconnect Mobility Dock
from socket and connect to vehicle fi rst
red permanently on
Temporary error (e.g. after overtemperature): Device
restarts automatically
red Flashing
Safety error (e.g. Mobility Dock installed upside
down): Disconnect the unit from the mains for 10
sec., rectify the fault and plug it in again
*)
WARNING STATUS DISPLAY The Mobility Dock is not suitable for
operation on extension leads or for horizontal operation. If the Mobility Dock
is lying on the ground, there is a risk of electric shock due to penetration of
liquids and housing damage due to being run over!
Do not use multiple sockets!
Do not dispose as unsorted
municipal waste
Do not use Mobility Dock if it is
lying on the fl oor
Follow the operating instructions
Type 2 power socket
WARNING indicates a danger with a
moderate risk of causing death or serious
injury if it is not avoided.
(B) Type2 outlet
unlocking device
(D) Wall support
unlocking device
10000038185.V1.2
1. 2. 3. 4. 5.
180°
Fig. 1 Product components
Fig. 2: Charging sequence Fig. 3: Unlocking the type2 outlet
Vehicle inlet
Wall socket
Lapp Mobility GmbH
Oskar-Lapp-Str. 2 · D-70565 Stuttgart
www.lappmobility.com

Chat with your Lapp Mobility Mobility Dock manual using AI

Get instant AI answers from your Lapp Mobility Mobility Dock manual

Ask anything about the Lapp Mobility Mobility Dock. Answers come from this manual, with the pages they are based on.

Mobility Dock Maintenance Schedule

Before each use
Inspect components for damage

Visually check all components for damage. Do not use damaged parts.

After use
Clean the unit

Disconnect from vehicle and mains before cleaning. Use only a slightly damp cloth.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend Mobility Dock?

Yes No
0
User Pic

rcox63

7 months ago

What is the charging power of this adapter, and do I need extra cables to use it with my vehicle?

0
User Pic

Manual.ly

7 months ago

This adapter provides 2.3 kW of charging power. You do not need a second cable inside your car. The standard Type 2 connector with an AC Mod2 cable is sufficient for operation. We also recommend securing the unit with the included wall mount for stability during use.

M: qwen/qwen3.5-flash-20260224
M: qwen/qwen3.5-flash-20260224
0
User Pic

Eileen Green

7 months ago

Does this charging adapter allow me to save space by using my existing Type 2 cable instead of the original wall box?

0
User Pic

Manual.ly

7 months ago

Yes, many users confirm it saves space. You only need your standard Type 2 charging cable. It replaces the original charging box and reduces the number of cables in your vehicle. It provides 2.3 KW power and mounts stably on a wall.

M: qwen/qwen3.5-flash-20260224
M: qwen/qwen3.5-flash-20260224

Frequently Asked Questions

A

A green light indicates standby or successful charging is in progress.

Is this answer helpful?

A

No, you must suspend it vertically to avoid liquid damage and shock risks.

Is this answer helpful?

A

The device features a charging power of 2.3 kW.

Is this answer helpful?

A

Yes, if charging exceeds two hours, set the vehicle rated current to 8 A.

Is this answer helpful?

A

Use a slightly damp cloth and avoid aggressive cleaning agents.

Is this answer helpful?

A

It indicates a safety error such as incorrect installation.

Is this answer helpful?

A

No, electronic waste must be recycled at designated collection points.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • IP44 protection rating for water and dust resistance.
  • Portable design suitable for various travel scenarios.
  • Clear LED status display for easy monitoring.
  • 2.3 kW charging power for efficient energy transfer.
  • Built-in residual current circuit breaker for safety.
VS

Disadvantages

  • Requires vertical mounting and cannot lie on the ground.
  • Must not be used with extension cords.
  • Unsupervised charging needs electrician verification for safety.
  • Strict storage requirements to prevent casing damage.
  • Not suitable for IT-networks or explosion risk zones.
M: qwen/qwen3.5-flash-20260224

Product Specification

Number of Charging Points

1

Max. Charging Power

2.3kW Single-phase

Charging Mode

IEC 61851-1 (Mode 2)

Number of Phases

1-Phase

Voltage

230V (AC)

Max Current per Phase

10A

Connection Type

Type 2, Grounded Socket

Installation

Mobile Charging Station

Special Features

Ground Fault Protection, Mobile Charging Station

Protection Class

IP44

Dimensions

10.04x5.31x4.13in (WxHxD)

Weight

1.65lbs

M: qwen/qwen3.5-flash-20260224

Product Description

Discover the Freedom of Electric Driving with the Lapp Mobility Mobility Dock

Owning an electric vehicle offers a sustainable future, but finding reliable charging solutions on the go can be challenging for modern drivers. The Lapp Mobility Mobility Dock manual outlines a practical solution for drivers who need flexibility without compromising safety standards. This portable charging device is specifically designed for Mode 2 charging, allowing you to connect your car securely to standard household or industrial sockets. Whether you are traveling between cities or parked for the day, this dock ensures your battery is replenished efficiently. The integration of modern safety technology ensures peace of mind during every journey.

Safety is the Absolute Priority

Safety remains at the forefront of the engineering design. The unit features an IP44 protection rating, meaning it tolerates splashes of water and dust ingress well enough for outdoor use. However, it is crucial to remember the critical instructions regarding placement. The dock must be suspended vertically from a wall socket. Using it while lying on the ground presents significant risks regarding liquid penetration. Always ensure the wall support is locked into place during operation to prevent undue strain on the electrical connection.

Technical Performance and Limits

With a charging power of 2.3 kW, this device suits many overnight or daytime charging needs effectively. It operates within a nominal voltage range of 230V AC at a frequency of 50 Hz. The included residual current circuit breaker adds an extra layer of protection against leakage currents. It is important to note that for specific regions like France and Finland, if charging extends beyond two hours, the vehicle must set the rated current to 8 A to maintain safety standards.

Operational Guidelines and Maintenance

Using the Mobility Dock involves straightforward steps outlined in the manufacturer documentation. Connect the vehicle coupling first, then the charging plug until it clicks. Unlock the wall support and suspend the unit vertically before plugging it into the mains. The status display provides clear feedback, with green lights indicating standby and charging states. Blue flashing signals reduced charging due to high ambient temperature. Cleaning requires a slightly damp cloth only, never using aggressive agents.

By understanding the warnings and proper storage methods found in the documentation, you protect your investment and ensure safety. This device is not for use with extension cords but a dedicated tool for safe mobility. Store it in a dry place within your boot, protecting the casing and mains plug. Respect the disposal rules for electronic waste to help the environment. Follow every instruction to avoid fire risks or electric shock during unsupervised charging cycles. Regular checks prevent potential hazards before they become serious problems. Proper maintenance extends the life of this vital equipment.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly