Manual.ly Logo

Kranzle quadro 9/170 TST Manual

0.0 · 0 Ratings

PDF manual · 19 Pages

English

M: gpt-5.6-terra
page

/ 19

Loading...
2f1b7c6a7d868b3310b12e2230f21117022b page d
24 25
1. Place chemicals filter into container
with additives.
2. Dosing of detergent is done by turning
the detergent valve.
By closing the detergent valve the
supply of detergent is stopped.
Only open the dosing valve, if the detergent sieve is placed in a liquid!
Sucked air leads to destruction of the pump seals of the high-pressure
cleaner (No warranty)!
The additive must reveal a neutral pH value of 7-9. This machine has been
designed for use of cleaning agents supplied or specifically recommended
by the manufacturer. The use of other cleaning agents or chemicals may
impair the safety of the machine. Observe and comply with relevant
regulations, e.g. directives governing protective equipment, waste-water
regulations, etc.
Attention solvents!
Never suck in liquids containing solvents like varnish solvents, petrol,
oil or similar liquids! Seals inside the high-pressure cleaner are no
resistant against solvents! The spray mist of solvents is highly
inflammable, explosive and poisonous.
Suction of additives
Due to the water tank fitted to the small quadro series it is now possible to
directly suck the detergent into the high-pressure pump thus reducing output
loss and increasing the efficiency considerably.
1. Switch off the high-pressure cleaner
2. Cut off the water supply
3. Open the safety trigger gun catch briefly until the pressure is released
4. Apply safety catch on the trigger gun
5. Remove high-pressure hose and safety trigger gun
6. Emptying high-pressure pump: Hold high-pressure hose and switch
motor on until water jet stops escaping at the outlet.
7. Pull the plug from the socket
8. Clean high-pressure hose and wind up without loops, fix hose drum
9. Clean and wind up the power supply cable
10. Clean the water inlet sieve
11. Apply locking brake
12. Store high-pressure cleaners in frost-free rooms in winter
Frost protection
For protecting the high-pressure cleaner against frost please empty it completely.
Separate high-pressure cleaner from water supply and switch it on. By opening
the safety trigger gun the high-pressure pump presses water out of the water
tank. However, do not allow the high-pressure cleaner to operate without
water for more than one minute. Fill the anti-freeze agent into the water box
and turn on the high-pressure cleaner. Wait with opened gun until the agent
spurts out of the nozzle.
Applying additives Taking out of operation

Chat with your Kranzle quadro 9/170 TST manual using AI

Get instant AI answers from your Kranzle quadro 9/170 TST manual

Ask anything about the Kranzle quadro 9/170 TST. Answers come from this manual, with the pages they are based on.

quadro 9/170 TST Maintenance Schedule

Remind me when maintenance is due
Yearly
Regular oil change

Change oil annually or every 250 operating hours. Change immediately if oil turns grey or white.

Show in the manual (page 13)
Yearly
Professional safety inspection

Have a qualified expert inspect the pressure washer at least every 12 months according to liquid jetting guidelines.

Show in the manual (page 13)
Every 50 hours
First oil change

Change the oil after approximately 50 operating hours for the first time.

Show in the manual (page 13)
Before each use
Check water inlet sieve

Clean the water inlet sieve before every start-up to ensure proper water flow and pressure buildup.

Before each use
Check oil level

Verify oil level on the dipstick before every start-up; it must reach the upper OK mark.

After each use
Clean water inlet sieve

Clean the water inlet sieve as part of the shutdown procedure after using the machine.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend quadro 9/170 TST?

Yes No

Frequently Asked Questions

A

It is suited to demanding cleaning of vehicles, equipment, paved areas, workshop spaces, exterior surfaces, and similar tasks. Adjust the pressure and choose the appropriate lance to suit the material being cleaned.

Is this answer helpful?

A

The package includes a stainless steel flat-jet lance for wider coverage and a Dirtkiller lance for concentrated cleaning power. Both use quick-release connections with the safety trigger gun.

Is this answer helpful?

A

When the trigger gun is released, the system stops the motor. Opening the trigger starts the motor and resumes pressurized water delivery. The machine remains in standby until switched off at the main switch.

Is this answer helpful?

A

Yes, it can draw clean water from a separate container when fitted and prepared for direct suction. The pump and suction hose must be filled with water before the first suction operation. Do not draw in air, chlorine-containing water, or dirty water.

Is this answer helpful?

A

Yes. Its detergent intake system can draw in suitable cleaning agents. Use neutral detergents with a pH of 7 to 9 and follow applicable wastewater and safety rules. Never use petrol, oil, paint thinner, or other solvent-containing liquids.

Is this answer helpful?

A

Check the water inlet filter, oil level, hose, trigger gun, lance connections, and power cable for condition and cleanliness. Ensure the water source supplies enough flow, use a suitable grounded outlet, and fully unwind cable reels.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Brass pump head, steel-braided 15 m hose, and sturdy trolley support demanding routine cleaning.
  • Infinitely variable pressure and flow adjustment help match the spray to different surfaces.
  • Total-Stop System stops the motor when the trigger is released, reducing idle operation.
  • Includes both flat-jet and Dirtkiller lances for broad cleaning and concentrated dirt removal.
  • Can use compatible detergents and can draw clean water from a separate container when configured.
VS

Disadvantages

  • Requires a dependable water supply; dry running or low flow can damage the high-pressure pump.
  • The powerful jet can damage sensitive surfaces, including tires, if used too closely.
  • Only neutral, manufacturer-suitable detergents should be used; solvents are prohibited.
  • Long or undersized extension cables can cause voltage drop and unreliable starting.
  • Frost protection, filter cleaning, oil checks, and annual inspection are important maintenance tasks.
M: gpt-5.6-terra

Product Specification

Operating mode

Cold water

Power

3,300 W

Pressure

435-2,466 psi

Flow rate

max. 142.65 gal/h

Inlet temperature

max. 140 F

Mobility

Wheeled chassis

Fuel tank

No

Dimensions

23.23 x 33.46 x 14.17 in (W x H x D)

Weight

103.62 lb

Included

High-pressure gun (M2000), high-pressure hose (49.21 ft), 2x lance/spray wand, detergent, hose reel, accessory holder, detergent hose, hose

M: gpt-5.6-terra

Product Description

Kränzle Quadro 9/170TST Electric High-Pressure Washer - Read, Download & Print Free

The Kränzle Quadro 9/170TST Electric High-Pressure Washer is a robust mobile cleaning machine designed for demanding domestic, agricultural, workshop, and commercial tasks. Its compact trolley layout, large wheels, locking brake, ergonomic handle, and integrated storage points make it practical to move across uneven ground while keeping essential equipment close at hand.

Built for controlled, efficient cleaning

This washer combines a brass pump head, a stainless steel pressure gauge, and continuously adjustable pressure and water volume control. Users can tailor the spray output to the surface, helping them work carefully around vehicles, paving, machinery, walls, and other areas that may need a gentler approach. The supplied flat-jet lance supports broad surface cleaning, while the Dirtkiller lance provides a more concentrated jet for stubborn grime.

A 15 m steel-braided high-pressure hose on a hose drum gives useful reach and supports organized storage between jobs. The Total-Stop System shuts the motor off when the trigger gun is released and restarts it when spraying resumes. This feature reduces unnecessary running time and makes operation more convenient during stop-and-start cleaning work.

Water supply and detergent options

The unit uses a water tank with a float valve to regulate incoming water. It can be connected to a suitable pressurized supply, and it can also draw clean water from a separate container when configured for direct suction. Reliable water flow is important: running the pump dry or using an inadequate supply can cause cavitation and premature wear.

For detergent-assisted jobs, the integrated chemical intake system can draw in compatible cleaning agents. Neutral products with a pH of 7 to 9 are recommended. Solvent-containing liquids, fuels, oils, and similar materials must never be used because they can damage seals and create serious fire, explosion, and health hazards.

Practical operating and care notes

Before use, inspect the hose, trigger gun, power cable, water inlet filter, and oil level. Use a grounded electrical supply protected by a 30 mA residual-current device, and select correctly rated extension leads if needed. Keep the hose free from kinks, avoid directing the spray at people, animals, electrical equipment, or the washer itself, and maintain at least 30 cm from delicate targets such as tires.

Notes

  • Drain the machine and protect it from frost before winter storage.
  • Clean the inlet filter regularly to maintain water flow and pressure.
  • Use approved Kränzle hoses, fittings, accessories, and replacement parts for safe operation.
  • Arrange regular qualified inspections, especially for commercial use.
M: gpt-5.6-terra

© Copyright 2026 Manual.ly