Legen Sie den Projektor mit der Unterseite nach oben auf eine weiche
Unterlage. Lockern Sie mit dem Sechskant-Schraubendreher
die
Profilarme des Projektorhalters. Richten Sie die Profilarme auf die Befe-
stigungsbuchsen des Projektors aus, siehe auch Anleitung des Projektors.
Entnehmen Sie aus dem Schraubensatz die für Ihren Projektor passenden
Schraubengrößen und Scheiben. Montieren Sie zuerst nach Abbildung
a
die 4 Gewindehülsen und 4 Muttern M10x1, und stellen Sie die Höhe eines
jeden Armes passend zum Projektorboden ein. Ziehen Sie anschließend
die Rändelmutter M10x1 zum Kontern handfest an,
b
. Montieren Sie nun
die passenden Schrauben und Unterlegscheiben nach Abbildung
c
in alle
Befestigungsbuchsen des Projektors.
Achtung: Es müssen mindestens 3 Gewindegänge eingeschraubt wer-
den. Keine Kleber oder Schmiermittel verwenden. Wenn die Montage nicht
richtig ausgeführt wird, kann der Projektor herunterfallen. Dabei besteht die
Gefahr von Verletzungen oder Unfällen.
Ziehen Sie nun alle Schrauben der vorhergehenden Schritte am
Projektorhalter fest.
a
b
a
bb
b
weight of the projector.
• Screw the bolts at least three turns into the drill-holes of the projector.
• If the screws are too long for the drill-holes of your projector,
use additional discs in order to prevent damages.
• The airflow of the projector is hot! Make sure that the unit keeps its
distance to other materials and that the flow of fresh air is not
hampered. The projector can be ruined by overheating.
• We are not responsible for subsequent damages in case of incompetent
mounting.
• Please keep this user manual.
Consignes de sécurité
• L’installation doit être uniquement eectuée par du personnel qualifié.
• Vérifier en tout cas la force de tenue du plafond soit susante pour
projecteur et support.
• Utiliser uniquement des vis de grosseur susante, qui sont spéciale-
ment conçues pour le matériel de plafond rencontré.
Ces vis ne sont pas livrées avec le support.
• Vérifier que la solidité de la matière du plafond est convenable pour un
montage définitif et qu’il y a aucun risque de chute.
Les matières de plafonds convenables sont: Bois dur, poutre d’acier,
béton.
• Faites un test de charge du double du poids.
• Les boulons d’attache doivent être tournés au moins trois fois dans le
pied du projecteur.
• Si les vis de montages sont trop longues, il faut utiliser des rondelles
supplémentaires pour ne pas endommager le projecteur.
• Un montage incorrect, un plafond défectueux ou non-convenable sont
des risques potentiels pour personnes, appareil et équipement!
• Le ventilateur du projecteur est chaud! Faites attention aux distances
nécessaires pour la circulation d’air et la distance aux autres matériaux.
L’appareil peut être endommagé à cause de surchaue, ou il peut
prendre feu!
• Nous ne sommes pas responsables en cas de montage non-approprié et
pour des préjudices ultérieurs.
• Les installations électriques ne doivent être faites que par du personnel
compétant.
• Conservez le mode d’emploi.
b) Un montage avec seulement 3 bras est possible
c) Longueurs spéciales de bras sur demande
Le porte-projecteur est attaché à une articulation ronde, et peut être tourné
de tous les côtés et incliné de 20°.
Fixer le porte-projecteur au projecteur
Posez le projecteur partie inférieure sur le dessus sur une surface douce.
Desserrez à l’aide du tourne-vis cruciforme
les bras profilés du
porte-projecteur. Orientez les bras sur les points de fixation du projecteur,
voir mode d’emploi du projecteur. Prennez du set de vis “pour fixation du
projecteur” les vis et rondelles correspondantes à votre projecteur.
Fixez selon l’illustration
a
les 4 vis profilées et 4 écrous M10x1, et réglez la
hauteur de chaque bras selon le socle du projecteur. Contre-serrez ensuite les
écrous moletés M10x1 à la main,
b
. Fixez ensuite les vis et rondelles
nécessaries selon l’illustration
c
dans les points de fixation du projecteur.
Attention: 3 pas de vis au minimum doivent être vissés. Ne pas utiliser de
colle ou de lubrifiant. Le projecteur peut tomber si le montage n’a pas été fait
correctement et peut ainsi causer blessures ou accident.
Serrez ensuite toutes les vis du porte-projecteur.
b
a
a
b
Fixing the projector holder
Put your projector on a soft surface (upside down). Loosen the movable
arms with a hexagon screw driver
. Adjust the arms to the location of
the drill-holes of the projector (see also manual of the projector).
Choose the suitable screws and discs from of the set supplied.
First fix the 4 threaded sleeves and 4 nuts M10x1
a
and adjust the height
c
d
a
a
Adjustment – Premium 60/100/150/200/250/300
The telescope column has a range for height adjustment.
In order to adjust, loosen the screw
c
with the delivered screw driver
.
Attention: Do not loosen the safety screw
d
!
By loosening the rotating knob
a
on the ball-and-socket joint the
projector can be rotated ±180 degrees and tilted about ±20 degrees.
Achtung: Die Sicherungsschraube
d
nicht lockern!
Durch Lockern der Halte-/Justageschraube
a
am Kugelgelenk kann der
eingesetzte Projektor um ±180° gedreht, sowie um ca. ±20° geneigt
werden.
Seite einhängen, durch Hochdrücken die Rastfeder
b
einrasten und eine der
beiden Halte-/Justageschrauben
a
eindrehen.
Achten Sie darauf, dass die Lüfterönungen des Projektors frei bleiben!
of each arm so that they fit to the projector bottom. Then tighten the knurled
nut M10x1
b
. Insert the suitable screws and discs (ill.
c
) into all drill-holes
of the projector.
Note: At least 3 threaded passages must be fixed. Do not use glue or
lubricants. Danger: The projector could fall down and cause injuries.
Now tighten all other screws on the projector holder.
a
b
c
Befestigung in diesem Bereich
nicht möglich!
Projector cannot be mounted
in this area!
Attaches dans ce rayon impossible!
Ø 138mm
Ø 378mm
/2
%
Quick check
I'm not a robot
Incorrect answer, please try again.
Chat with your Kindermann Premium manual using AI
Get instant AI answers from your Kindermann Premium manual
Ask anything about the Kindermann Premium. Answers come from this manual, with the pages they are based on.
Ask a Question
0/1000
Do you recommend Premium?
YesNo
Frequently Asked
Questions
A
It is a ceiling mounting system for projectors, built to hold the device securely while allowing easy positioning and alignment. The design suits professional, educational, and home theater installations.
Is this answer helpful?
A
Depending on the model, the height can be fixed or continuously adjusted over a wide range. The holder also rotates 360 degrees and tilts about ±20 degrees for flexible aiming.
Is this answer helpful?
A
The projector must not exceed 25 kg. Staying within this limit is important for safe installation and long-term stability.
Is this answer helpful?
A
Yes, with the appropriate accessory. An optional tilting joint is available for ceilings with up to 45° inclination.
Is this answer helpful?
A
Yes. The system includes cable covers and an internal cable channel so power and signal wiring can be routed more neatly through the mount.
Is this answer helpful?
A
The ceiling must be strong enough, the correct screws must be used, and the projector’s ventilation openings must remain unobstructed. After installation, the mount should be tested with a load check.
Is this answer helpful?
M: OA-GPT-54-NAN
Advantagesand
Disadvantages
Advantages
Wide height adjustment range across multiple Premium models.
360° rotation and ±20° tilt support precise projector alignment.
Cable routing options help create a neat, professional installation.
Accessory options expand use for sloped ceilings, tube mounts, and security.
VS
Disadvantages
Installation requires careful setup and qualified handling.
Mounting hardware for the ceiling is not included.
Weight limit of 25 kg may exclude heavier projectors.
Poor ventilation or incorrect screws can cause damage or safety risks.
M: OA-GPT-54-NAN
Product
Specification
Type
Ceiling mount
Ceiling distance
5.12 in
Tilt angle
20°
Max. load capacity
55.12 lb
Color
silver
M: OA-GPT-54-NAN
Product
Description
Kindermann Premium Manual: A Flexible Ceiling Mount for Projectors
The Kindermann Premium series is designed for installers and users who want a dependable ceiling solution for projector setups. Built around a telescopic column and a ball-and-socket joint, it combines sturdy support with practical adjustability. The system is intended to keep projectors securely mounted while allowing fine positioning for height, rotation, and tilt.
One of the strongest points of the Kindermann Premium Manual is its versatility. Depending on the model, the distance between projector and ceiling can be fixed or continuously adjusted across a wide range. The premium variants cover different installation needs, from compact rooms to larger spaces requiring more drop length. The holder can rotate 360 degrees and tilt by roughly ±20 degrees, making alignment much easier during setup.
Installation is built around a modular design. The projector is attached using adjustable arms, suitable screws, washers, and threaded sleeves, which help match different projector mounting patterns. The system also includes cable management parts so wiring can be routed neatly through the column. This creates a cleaner appearance and helps protect connections.
Safety is clearly a major focus. The instructions stress correct ceiling strength, qualified installation, and proper ventilation around the projector. The projector weight must not exceed 25 kg, and the mounting must be tested carefully after installation. Users are also advised to leave the ventilation openings unobstructed so heat can escape properly.
The series supports several mounting environments, including flat ceilings and, with optional accessories, sloped ceilings or tube-shaped supports. Optional add-ons such as anti-theft protection and adapter plates expand its usefulness in commercial, educational, and public installations. Finish options like anodized aluminum or white RAL 9003 help the mount blend into different interiors.
Overall, Kindermann Premium stands out as a professional-grade projector mounting solution that balances adjustability, appearance, and structural safety. It is well suited for anyone looking for a reliable ceiling mount with practical installation features and long-term stability.