Get instant AI answers from your Kemo M100N manual
Ask anything about the Kemo M100N. Answers come from this manual, with the pages they are based on.
Ask a Question
0/1000
Do you recommend M100N?
YesNo
0
Lukas Schneider
9 months ago
How difficult is the installation, and are the connection wires long enough for common car models? I heard some cables are too short - what should I do?
0
Manual.ly
9 months ago
Installation is usually straightforward, but you should plan for the power connection. Several users reported that the supplied wires can be short on some vehicles. If needed, you can carefully extend the wires with a solder joint and heat-shrink tubing (use proper insulation). Also make sure you connect to a suitable 12V supply that changes correctly with ignition and to proper ground (mass). Before mounting, clean the engine bay thoroughly, as dirt can interfere with placement/monitoring. In general the device can help, but there is no absolute 100% guarantee for every car situation or every individual animal.
M: OA-GPT-5-NAN
M: OA-GPT-5-NAN
Frequently Asked
Questions
A
The device operates at approximately 23 kHz, producing ultrasonic pulsing tones designed to irritate martens while remaining inaudible to humans.
Is this answer helpful?
A
Operating voltage is 11–15 V DC with an average current consumption of less than 2 mA. For 24 V vehicle systems an M020 voltage converter (24 V to 12 V) must be used (sold separately).
Is this answer helpful?
A
Mount where the loudspeaker opening faces as much free space as possible—typically on the rear bulkhead near the cabin or at the front beside the radiator fan. Avoid hot areas such as near the exhaust manifold to prevent heat damage (>80°C reduces lifespan).
Is this answer helpful?
A
Not always. In highly cleaved or large motor compartments multiple units may be needed to reach vulnerable cables and hoses. Ultrasonic sound propagates in straight lines and can miss some corners.
Is this answer helpful?
A
Yes. If martens have marked the vehicle with scent, thoroughly clean the motor bay and the parking area to remove scent marks, otherwise the animal may defend its territory and continue to cause damage.
Is this answer helpful?
A
Connect the repellent to terminal 15 so it becomes active when the ignition is off. If terminal 15 on your car follows Euro norms it is available at the radio connector and should be marked accordingly.
Is this answer helpful?
A
Yes. Remove the fuse (switch off) before welding, using a fast charger, or jump-starting to avoid damaging the device from high voltage impulses. Ensure the unit is mounted to prevent water or dirt ingress.
Is this answer helpful?
M: OA-GPT-5-NAN
Advantagesand
Disadvantages
Advantages
Emits pulsing ultrasonic tones (≈23 kHz) that are inaudible to humans but irritating to martens.
Hemispherical dome tweeter provides wide coverage (>140°) to treat broad areas rather than a narrow beam.
Low average current consumption (<2 mA) and compact dimensions for easy installation in motor bays and lofts.
Can be connected to terminal 15 to switch on automatically when vehicle is parked.
Suitable for 12 V systems; operable in 24 V vehicles with optional M020 converter.
VS
Disadvantages
Does not guarantee complete marten removal; animals may relocate to other vehicles or areas.
Requires knowledgeable installation to avoid hot engine parts and ensure effective coverage.
May need multiple units in highly partitioned motor compartments, increasing cost.
Must remove fuse before welding, jump-starting or rapid charging to prevent damage.
If martens have left scent marks, motor cleaning is required for effectiveness.
M: OA-GPT-5-NAN
Product
Specification
Type
Ultrasonic device
Operating voltage
12V
Power consumption
<2mA
Frequency range
23kHz
Beam angle
140°
Special features
CAN-Bus compatible
Dimensions
2.83x1.97x1.10in
M: OA-GPT-54-NAN
Product
Description
Kemo Ultrasonic Marder Repellent Manual
The Kemo Ultrasonic Marder Repellent (M100N) is a compact ultrasonic device designed to deter martens from cars, lofts and homes by emitting pulsing, high-frequency sounds (around 23 kHz) that are inaudible to humans but highly irritating to martens. Built with a hemispherical dome tweeter offering a wide radiation angle (>140°), the unit aims to blanket a broad area in clean ultrasonic tones rather than focusing an excessively loud narrow beam. This approach replicates more natural-sounding warning calls, increasing the chance martens perceive and avoid the treated area.
Installation and use are straightforward but should be performed by knowledgeable personnel. For automobiles the recommended mounting positions are where the loudspeaker has as much free space as possible—commonly on the bulkhead behind the cabin or at the front near the radiator fan—avoiding hot spots such as near the exhaust manifold. The device runs from 11–15 V DC (average consumption <2 mA) and includes an LED that blinks after correct power connection; reverse polarity or absent voltage is indicated if the LED does not flash properly.
For 24 V vehicle systems a separate M020 voltage converter (24 V to 12 V) must be placed in series (sold separately). The repellent is best connected to the vehicle’s terminal 15 so it operates automatically when the car is parked. If the motor bay is highly convoluted, multiple units may be necessary to cover vulnerable cables and hoses.
Important practical notes cover safety and effectiveness: if a marten has already been present, thoroughly clean motor bay and parking-area scent marks—martens mark territory and may defend it if startled. Turn off the device (remove fuse) before welding, rapid charging, or jump-starting to avoid electrical surges. The manufacturer warns that ultrasonic repellents cause significant discomfort to animals and may shift pests to other vehicles or locations; full eviction is not guaranteed.
Technical highlights include small dimensions (~72 x 50 x 28 mm), operating voltage 11–15 V DC, frequency approx. 23 kHz, average current <2 mA, radiation angle ~140°, and max sound level around 110 dB ±20% (noted that wide-field emission is preferred over focused horn-style transducers).
Notes
Clean motor bay and parking area if martens were present to remove scent marks.
Use terminal 15 so the device is active only when parked.
For 24 V systems, purchase and install module M020.
Remove fuse before welding, jump-starting, or using a rapid charger.
Multiple units may be required for complex engine bays or larger spaces.
Lukas Schneider
9 months ago
How difficult is the installation, and are the connection wires long enough for common car models? I heard some cables are too short - what should I do?
Manual.ly
9 months ago
Installation is usually straightforward, but you should plan for the power connection. Several users reported that the supplied wires can be short on some vehicles. If needed, you can carefully extend the wires with a solder joint and heat-shrink tubing (use proper insulation). Also make sure you connect to a suitable 12V supply that changes correctly with ignition and to proper ground (mass). Before mounting, clean the engine bay thoroughly, as dirt can interfere with placement/monitoring. In general the device can help, but there is no absolute 100% guarantee for every car situation or every individual animal.