Manual.ly Logo

Kathrein EXR 1942 Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: OA-GPT-5-NAN
page

/ 24

Loading...
bd9362c982fa6095c354a28533a44c984a0e page 5
1 / 4
Cascadable single-cable multi-switch for distribution of
digital Sat-IF signals (8 sat levels; including HDTV) and
terrestrial signal for supplying 2 x 4 receivers in single-
family households
No restriction on the variety of channels - the complete
range of channels from two satellites is transmitted
Option to select horizontal/vertical, low band/high
band satellite position A/position B and transponder
independently for each receiver
Switching horizontal/vertical, low band/high band,
satellite position A/position B and transponder selection
is carried out in the multi-switch, controlled by the
receiver with a special SCR single-cable command set
to EN 50494
For transponder selection special tuner modules called
SCRs (Satellite Channel Routers) are incorporated
in the single-cable multi-switch for conversion to the
subscriber frequencies
Each receiver is assigned a fi xed subscriber frequency
(a twin receiver requires two subscriber frequencies)
The unit satisfi es EN 50494, i.e. all components of an
SCR single-cable system that satisfy this standard can
be installed in a satellite system
Terrestrial signals can be received even when the
satellite receiver is switched off
EXR 2942 single-cable multi-switches and EXR 2998
loop-through multi-switches can be mixed in any
combination. Up to 8 multi-switches can be connected
in a cascade
For indoor installation
Sat-IF distribution system (8 x Sat-IF)
Single-cable multi-switch
Features
EXR 1942
Single-cable multi-switch for two single-cable
connections, each for four receivers, with
integral power supply unit for the LNB supply
Low power consumption thanks to highly
effi cient, short-circuit protected switched-mode
power supply unit and power-saving concept
(the single-cable multi-switch is supplied by
the receivers that are connected to it and is
switched off when the receivers are switched
off)
LNB remote feed via the horizontal low inputs.
All other inputs are voltage-free
EXR 2942
Single-cable multi-switch loop-through
for system extension to two single-cable
connections, each for four receivers
EXR 1942 20510040
EXR 2942 20510041

Chat with your Kathrein EXR 1942 manual using AI

Get instant AI answers from your Kathrein EXR 1942 manual

Ask anything about the Kathrein EXR 1942. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EXR 1942?

Yes No

Frequently Asked Questions

A

The EXR 1942 is a single‑cable multi‑switch for indoor distribution of digital satellite IF (8 levels, including HDTV) and terrestrial signals to two single‑cable outputs supporting up to four receivers each, enabling independent channel selection per receiver.

Is this answer helpful?

A

Yes. EXR 1942 units can be mixed with EXR 2942 loop‑through multi‑switches and up to eight multi‑switches may be cascaded to expand installations while maintaining SCR single‑cable operation.

Is this answer helpful?

A

The EXR 1942 has an integrated switched‑mode PSU with low consumption; it is normally fed by connected receivers and powers down with them. LNB remote feed is provided via the horizontal low inputs; other satellite inputs remain voltage‑free.

Is this answer helpful?

A

Assign each available subscriber frequency at the multi‑switch output to only one receiver. Set unique frequencies in the receiver menu (manual or automatic depending on model) to prevent mutual interference.

Is this answer helpful?

A

No. The EXR 1942 is for dry indoor installation only. Do not mount on or against easily combustible materials and ensure adequate clearance and ventilation to avoid overheating.

Is this answer helpful?

A

Provide equipotential bonding (Cu, ≥4 mm²), comply with EN 60728‑11 and EN 60065, use F‑connectors and terminate unused RF ports with 75 Ω resistors, and ensure receiver output voltage does not exceed 14 V to prevent faults.

Is this answer helpful?

A

18 V is briefly applied to transmit DiSEqC‑like control signals; continuous 18 V will block the system. Use sockets with electronic shut‑off (e.g., ESU 33/34) to prevent extended 18 V application.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • EN 50494 SCR single‑cable compliance ensures interoperability with SCR‑capable receivers.
  • Low power consumption with switched‑mode PSU and receiver‑driven power saving behavior.
  • Supports 2x4 subscriber outputs and mixing/cascading up to 8 multi‑switch units for system expansion.
  • Terrestrial signal available even when satellite receivers are switched off.
  • Integrated SCR tuner modules convert transponder selections to fixed subscriber frequencies.
VS

Disadvantages

  • Indoor‑only mounting required; not suitable for wet or outdoor environments.
  • Requires receivers compatible with EN 50494 single‑cable operation.
  • Incorrect frequency assignment can cause mutual interference between receivers.
  • Continuous 18 V DC will block the system — careful power/control handling needed.
  • Limited remote feed current constraints may restrict some LNB configurations.
M: OA-GPT-5-NAN

Product Specification

Satellite Inputs

8

Terrestrial Inputs

1

Outputs

2 (Unicable)

Unicable

max. 8 participants total, max. 4 participants per output

Cascadable

yes

Satellite Positions

2

Dimensions

8.94x8.98x1.73in (WxHxD)

Weight

2.20lb

M: OA-GPT-54-NAN

Product Description

Kathrein EXR 1942 — Reliable Single‑Cable Multi‑Switch

The Kathrein EXR 1942 is a compact, indoor single‑cable multi‑switch designed to distribute digital satellite IF signals (8 Sat‑IF levels, HDTV capable) and terrestrial signals to two single‑cable outputs serving up to four receivers each. Built to the EN 50494 SCR single‑cable standard, the EXR 1942 enables each receiver to independently select polarization, low/high band, satellite position A/B and transponder via SCR commands, while integrated Satellite Channel Router (SCR) tuner modules convert selections to fixed subscriber frequencies.

Energy efficiency is a key advantage: the EXR 1942 features a highly efficient, short‑circuit protected switched‑mode power supply and a power‑saving concept where the unit is supplied by connected receivers and powers down with them. LNB remote power is provided via the horizontal low inputs; other satellite inputs remain voltage‑free. The unit supports mixing with EXR 2942 loop‑through switches and up to eight multi‑switches can be cascaded for larger installations. Terrestrial signals remain available even when satellite receivers are switched off.

Practical for installers, the EXR 1942 offers F‑connector terminations, clear SCR subscriber frequency assignments, and a frequency range covering terrestrial and Sat‑IF bands (5–862 MHz terrestrial, 950–2150 MHz Sat‑IF). It includes protective and operational guidelines: indoor, dry mounting only; equipotential bonding required; adherence to EN 60728‑11 and EN 60065; and correct termination of unused RF ports with 75 Ω resistors.

Installation notes emphasize correct SCR frequency assignment (each subscriber frequency must be unique), receiver compatibility with EN 50494, and brief 18 V DC switching for DiSEqC‑like control signals (continuous 18 V must be avoided). The EXR 1942 also provides technical detail useful for commissioning: permissible supply voltages, remote feed currents, ambient temperature range, and mechanical constraints.

Overall, the EXR 1942 is aimed at single‑family installations requiring reliable multi‑satellite distribution with single‑cable convenience, standards compliance, and energy‑aware operation.

Notes

  • Compliant with EN 50494 SCR single‑cable standard for interoperable systems.
  • Use ESU 33/34 sockets or equivalents to avoid continuous 18 V lock‑up during control signaling.
  • Ensure unique subscriber frequency allocation to prevent receiver interference.
  • Mount indoors with at least 5 cm clearance and avoid exposure to moisture.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly