Manual.ly Logo

Kathrein EXR 1708 Manual

0.0 · 0 Ratings

PDF manual · 8 Pages

English

M: OA-GPT-5-NAN
page

/ 8

Loading...
63d05db5d89ee410fcaec84ff0c4b1c28fd2 page 5
1 / 4
•
Cascadable multi-switch for splitting 16 sat levels and terrestrial
signals to multiple receivers
•
Only one downlink per receiver needed
(two for twin receivers)
•
Facility to select horizontal/vertical, low/high, sat positions
A/B/C/D independently for each receiver using DiSEqC
TM
controls
•
If not using DiSEqC
TM
controls, changing the horizontal/vertical,
low/high of sat position A can be performed, also by tone burst
changing sat position A/position B
•
Integral amplifi er for low attenuation in sat signal band
•
Integral pre-emphasis to equalise cable attenuation
•
Terrestrial signals also receivable with sat receiver switched o
•
Terrestrial range 5-862 MHz passive
•
High degree of insulation between outputs
•
Can be remote fed via the horizontal low inputs.
All other inputs are voltage-free
(enabling operation with UAS 485)
•
For indoor installation
EXR 1708
•
Multi-switch for 8 connections, with integral power supply unit
•
Low power consumption based on high-e ciency short-circuit-
proof switch-mode power supply unit
•
Can be extended using EXR 1718
EXR 1718
•
Multi-switch loop-through for system extension to eight
connections each
•
Highly cascadable (up to 40 connections)
Multi-switch
KLASSE
CLASS
D SE
2.0
i q
C
Terr.
H high
V high
H low
V low
Pos A
V high
H low
V low
H high
Pos B
H high
V high
H low
V low
Pos C
V high
H low
V low
H high
Pos D
62 4 8
EXR 1718
Made in EC
20510028
51 3 7
374
388
182
153,45
KLASSE
CLASS
DSE
2.0
i
q
C
Terr.
H high
V high
H low
V low
Pos A
V high
H low
V low
H high
Pos B
H high
V high
H low
V low
Pos C
V high
H low
V low
H high
Pos D
62 4 8
EXR 1708
Made in EC
20510027
51 3 7
230V~ / 32 W
374
388
248,5
219,95
H low: max. 1500mA sum
Setting E ect
22 kHz → High/Low All position “A” inputs can be selected
Tone burst → Pos. A/B All position “A” and “B” inputs can be selected
The terms for the settings in the receiver menus are specifi c to the respective model and manufacturer!
Settings for receivers without DiSEqC™
Setting E ect
DiSEqC™ “On” All inputs can be selected
22 kHz and tone burst to “O ” Changeover time is shortened
Settings for receivers with DiSEqC™
Sat-IF distribution system (16 x Sat-IF) Multi-switch
EXR 1708 20510027
EXR 1718 20510028
suitable for DVB-T/T2

Chat with your Kathrein EXR 1708 manual using AI

Get instant AI answers from your Kathrein EXR 1708 manual

Ask anything about the Kathrein EXR 1708. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EXR 1708?

Yes No

Frequently Asked Questions

A

The EXR 1708 distributes 16 satellite IF levels plus terrestrial signals to multiple receivers, offering DiSEqC-controlled per-receiver selection of polarization, band and satellite position, with an integrated power supply and amplifier.

Is this answer helpful?

A

Yes. It supports DiSEqC commands to independently select vertical/horizontal, low/high bands and satellite positions A/B/C/D for each receiver. If DiSEqC is unavailable, legacy controls (14/18 V, 0/22 kHz and Tone Burst) provide limited switching.

Is this answer helpful?

A

Yes. The terrestrial path (5–862 MHz) is provided passively and remains available even if satellite receivers are powered off, enabling combined satellite and terrestrial distribution to subscribers.

Is this answer helpful?

A

The EXR 1708 provides 8 subscriber outputs and can be expanded using Kathrein EXR 1718 loop-through units to scale installations — high cascadability supports much larger systems (manufacturer guidance up to ~40 connections).

Is this answer helpful?

A

Install indoors in dry locations with at least 5 cm clearance for ventilation, earth the unit with a minimum 4 mm² copper conductor, use 75 Ω F-connectors, avoid ceiling mounting, and terminate unused outputs with 75 Ω resistors. Observe connector torque and cable core diameter limits to prevent damage.

Is this answer helpful?

A

Remote feeding is possible via the horizontal low inputs. The unit’s maximum total remote feed current is 1500 mA (via those inputs). Installers should ensure load distribution and remote power limits are not exceeded.

Is this answer helpful?

A

Yes. The EXR 1708 complies with applicable standards and directives, including necessary EN norms and the EU Radio Equipment Directive; full conformity information is available from Kathrein.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • DiSEqC support for independent per-receiver selection of polarization, band and satellite position.
  • Integrated amplifier and pre-emphasis reduce cable attenuation and preserve signal quality.
  • Low power consumption via short-circuit-proof switch-mode PSU and remote-feed capability.
  • Expandable with EXR 1718 for large, cascadable systems (up to ~40 connections).
  • Passive terrestrial path (5–862 MHz) available even with satellite receivers switched off.
VS

Disadvantages

  • Indoor-only mounting and IP30 rating restricts outdoor or damp-location installations.
  • Requires correct earthing (Cu ≥ 4 mm²) and careful connector/cable preparation to avoid damage.
  • Legacy switching without DiSEqC is limited to primary positions (A and optionally B).
  • Some installers may need to manage remote feed current limits (max 1500 mA total).
  • Not suitable where ceiling mounting or fully weatherproof installations are required.
M: OA-GPT-5-NAN

Product Specification

Satellite Inputs

16

Terrestrial Inputs

1

Outputs

8

Cascadable

yes

Satellite Positions

4

Dimensions

15.28x1.77x9.80in (WxHxD)

M: OA-GPT-54-NAN

Product Description

Kathrein EXR 1708 — Powerful, Cascadable Multiswitch

The Kathrein EXR 1708 is a robust multiswitch designed for distributing 16 satellite IF levels plus terrestrial signals to multiple receivers in medium-sized installations. Built for indoor mounting, it features an integrated power supply and efficient switch-mode PSU to minimize power consumption while delivering reliable performance. The unit supports DiSEqC control for per-receiver selection of polarization (vertical/horizontal), band (low/high) and satellite positions (A/B/C/D). When DiSEqC is not available, common legacy controls (14/18 V, 0/22 kHz, Tone Burst) allow basic switching between primary positions.

Performance-wise, the EXR 1708 includes an internal amplifier to keep satellite feed attenuation low and a pre-emphasis stage to compensate for cable loss over long runs. Terrestrial signals (5–862 MHz) are passed through passively and remain available even with satellite receivers powered off. The device allows remote powering (remote feed) via the horizontal low inputs and keeps other inputs voltage-free, enabling compatibility with external power control systems such as UAS 485.

The EXR 1708 is intended to work with expansion modules like the EXR 1718 to scale systems up to dozens of connections with high cascade capability. Connectors are standard F-type, screening and output decoupling meet industry expectations, and the unit meets relevant safety and EMC standards. Installation notes emphasize indoor, dry mounting, correct earthing with a minimum 4 mm2 conductor, proper connector torque and cable conductor diameters to avoid damage.

Practical benefits include straightforward receiver compatibility (DiSEqC and legacy modes), compact footprint, and high output isolation to prevent cross-talk. The product suits apartment blocks, hotels, or multi-dwelling units where centralized satellite distribution and expansion flexibility are required.

Notes

  • Supports DiSEqC commands for per-receiver satellite selection (A/B/C/D).
  • Terrestrial path remains available even when satellite receivers are off.
  • Use 75 Ω F-connectors and terminate unused outputs with 75 Ω resistors.
  • Keep free airflow around the unit; maintain at least 5 cm clearance.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly