Manual.ly Logo

Kathrein ESU 53 Manual

0.0 · 0 Ratings

PDF manual · 5 Pages

English

M: OA-GPT-5-NAN
page

/ 5

Loading...
bfa86475b765c792e816b047c0d884377813 page 4
1 / 2
ESU51 21110061
ESU53 21110026
ESU54 21110027
ESU56 21110028
ESU57 21110029
Programmable Single-cable Outlets
For single-cable systems according to EN50494 and EN50607
With DC voltage feed-through via satellite connection to the trunk
line (max.24V/400mA, 22kHz- and DiSEqC
TM
signal)
Monitoring of DiSEqC
TM
signalling by microcontroller
Overload protection by means of an electronic fuse and decoupling diodes
Return-path compatible for systems with cable connection (CATV
modem) or in IP over Coax systems, e.g. with KLAN modem (EXI01)
Congurable functions with the SWP50 programming device:
– disabling individual user bands
– operation in Legacy mode (no switch-off at 18 V constant signal
for standard multi-switch system)
– operation in disconnect mode (no DC feed-through to the trunk)
–
LED display for status and fault indication (can be switched off)
– Functions can be expanded.
Basic functions at delivery:
– The connected receiver is switched off if it does not use the
single-cable DiSEqC
TM
command set in accordance with
EN50494 or EN50607 (switching off the power from the satellite
connection to the input at +18 V
DC
after approx. 400 ms).
– congured for single-cable systems according to EN 50494 and
EN 50607
– All user bands (UB1…UB32) are enabled.
– LED display switched off
Connections:
– TV: IEC connector (m) (IEC61169-2)
– Radio: IEC connector (f) (IEC61169-2)
– SAT: F-socket (IEC61169-24)
With screw and claw fastening for ush-mounted installation boxes
Ø55–65mm
TV SAT
Radio
Service LED
OutputInput
Programming
interface
Fig. 1: ESU53
ESU51
Terminated end outlet, 8dB, for radial and star distribution systems
or as an end outlet for loop-through systems
ESU53, ESU56, ESU57
– Directional coupler outlet, 10dB, 14dB and 17dB for loop-
through systems
– Use ERA14 – order number272899–as a terminating resistor!
ESU54
Single outlet, 1dB, for radial or star distribution systems
Characteristics
Functional Specification
In single-cable satellite reception systems, interferences are possible if
individual subscribers or receivers block the trunk line by means of an
18V constant signal. Due to these interferences, other subscribers are no
longer able to communicate with the multi-switch or LNB.
In practice, it is also possible that incorrectly congured receivers use
the user IDs of other subscribers. In this case, we are talking about
interferences in the form of the so-called ping-pong effect, because two
subscribers “ght“ for the same transponder.
The single-cable outlets of the ESU5x series have a microcontroller
that monitors signalling inside single-cable systems
. In addition to signal
voltages
(14V/18V), audio signals (22kHz) or DiSEqC
TM
signals are also
analysed.
The antenna outlets turn off a permanent voltage of 18V and, by means of
a user ID check, ensure that only the enabled user band IDs are transmit-
ted from the receiver to the multi-switch via the outlet.
The programming device SWP50 transmits the user band IDs which need
to be enabled to the single-cable antenna outlet, thus ensuring that the
subscribers in a single-cable antenna system do not interfere with each
other.
Using the programming device SWP50, a specialist retailer or installer
congures one or several dened user IDs in the single-cable antenna
outlet during the installation of the antenna system. To do so, the special-
ist retailer or installer connects the programming device to the F-socket
of the antenna outlet. By means of the Kathrein ESU app, a connection to
the programming device is established, and the data for the conguration
of the antenna outlet is transmitted to the programming device.
Notes for the Installer
To adjust other functions, the programmer SWP50–order number
21110025–and the Kathrein ESU app – available for free for various
operating systems – are required; see Fig. 2.
Pay attention to the SWP50 and Kathrein ESU user guide.
To congure a single-cable outlet according to the antenna system
layout, connect the SWP50 to the SAT connection (F-type con-
nector) of the outlet and follow the instructions in the SWP50 and
Kathrein ESU. You can do it either before or after the outlet has been
installed in the system.
We recommend keeping records of the enabled user band IDs of the
outlet for the user.
When conguring an outlet, do not disconnect it from the SWP50.
Follow the installation instructions below to install the outlet.
Fig. 2: Programming device SWP50

Chat with your Kathrein ESU 53 manual using AI

Get instant AI answers from your Kathrein ESU 53 manual

Ask anything about the Kathrein ESU 53. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend ESU 53?

Yes No

Frequently Asked Questions

A

The ESU 53 is a programmable single‑cable (Unicable/JESS) satellite outlet that monitors DiSEqC and voltage signalling to prevent interference between subscribers and to enable controlled transmission of userband IDs to the multiswitch.

Is this answer helpful?

A

Configuration is done with the SWP 50 programming device (order no. 21110025) and the free Kathrein ESU app. The installer connects the SWP 50 to the outlet’s F‑socket and uploads the allowed userband IDs. Do not disconnect the programmer until configuration completes.

Is this answer helpful?

A

It offers overload protection via an electronic fuse and decoupling diodes, DC pass‑through to the trunk (max 24 V / 400 mA), return‑path compatibility for CATV or IP‑over‑Coax devices, and configurable modes such as Legacy and Disconnect to match existing systems.

Is this answer helpful?

A

Red indicates a sustained 18 V or 22 kHz signal (>400 ms) or overload (>500 mA); flashing red signals a DiSEqC command with a blocked userband. Green shows programming in progress; flashing green indicates a DiSEqC command with an enabled userband.

Is this answer helpful?

A

Yes. The device supports a Legacy mode that avoids shutting off at an 18 V constant signal and a Disconnect mode to disable DC pass‑through, making it adaptable for many retrofit scenarios when configured by a qualified installer.

Is this answer helpful?

A

The ESU 53 features an F‑type socket for SAT, an IEC male for TV and an IEC female for radio. It mounts into flush installation boxes Ø 55–65 mm using screw and claw fastenings.

Is this answer helpful?

A

The ESU 53 is electronic equipment and must not be disposed of with household waste. Follow local regulations and return the unit to designated public collection points for proper electronic waste recycling.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Active monitoring of DiSEqC and voltage signalling prevents interference and ping‑pong conflicts between receivers.
  • Programmable userband locking (UB1…UB32) via SWP 50 and app allows precise access control per outlet.
  • Return‑path compatible for CATV or IP‑over‑Coax systems while still supporting DC pass‑through to trunk.
  • Robust shielding and low insertion loss across TV/SAT frequency ranges, compliant with EN standards.
  • Flexible operation modes (Legacy, Disconnect) to suit existing multiswitch installations.
VS

Disadvantages

  • Requires the SWP 50 programming device and app for full functionality and secure configuration.
  • Initial setup must be performed by qualified installers; incorrect configuration can cause service issues.
  • DC pass‑through current limited (max 400 mA) which may restrict some powered devices on the trunk.
  • All userbands shipped enabled by default; installers must proactively lock bands to prevent conflicts.
  • Programming interruption during configuration can corrupt settings—device must remain connected until completion.
M: OA-GPT-5-NAN

Product Specification

Type

Pass-through socket

Connections

3

Frequency range

5-2150MHz

Suitable for

1x SAT, 1x TV, 1x Radio

Tap loss

10dB

Through loss

1.9dB

Special features

programmable Userband ID

M: OA-GPT-54-NAN

Product Description

Kathrein ESU 53 — Programmable Single‑Cable Satellite Outlet

The Kathrein ESU 53 is a programmable single‑cable satellite outlet designed for modern single‑cable (Unicable/JESS) installations compliant with EN 50494 and EN 50607. Built as a directionally coupled outlet with typical coupling around 10 dB, the ESU 53 integrates a microcontroller that monitors DiSEqC and voltage signalling to prevent interference between subscribers and misconfigured receivers. It supports DC pass‑through to the trunk (max 24 V / 400 mA) while offering overload protection via an electronic fuse and decoupling diodes, and includes a service LED to indicate status, faults, programming and load conditions.

Installation and configuration are performed with the SWP 50 programming device and the free Kathrein ESU app. During setup the installer programs allowed userband IDs (UB1…UB32) into the outlet so only authorised user bands reach the multiswitch, eliminating conflicts such as the ping‑pong effect when two receivers attempt the same transponder. Out of the box the ESU 53 ships with all user bands enabled and the LED off; installers typically restrict bands per household requirements.

The outlet’s mechanical design supports flush‑mounted boxes (Ø 55–65 mm) with screw and claw fastenings and provides IEC connectors for TV and radio plus an F‑type socket for SAT. Return path compatibility makes it suitable for hybrid installations using CATV modems or IP‑over‑Coax solutions. The device fulfils shielding and screening standards, provides low insertion loss across wide frequency bands, and meets EN 60728‑11 and EN 50083‑2 norms.

Typical use cases include multi‑dwelling single‑cable distribution, hotels or commercial buildings where multiple receivers share a trunk line, and retrofit projects converting legacy multiswitch systems into controlled single‑cable environments. The unit’s programmable modes—Legacy (no shutoff at 18 V), Disconnect (no DC pass‑through), and user‑band blocking—allow flexible adaptation to existing infrastructure and user needs.

Overall, the Kathrein ESU 53 is aimed at professional installers and system integrators seeking robust, configurable protection against inter‑user interference while preserving return path options and high shielding performance.

Notes

  • Configuration requires the SWP 50 programmer (order no. 21110025) and the Kathrein ESU app. Do not disconnect the programmer during configuration.
  • Document and hand over enabled userband IDs to the end user for support and maintenance.
  • Use proper termination (ERA 14) where specified for loop‑through systems.
  • Dispose of the unit through appropriate electronic waste channels according to local regulations.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly