Manual.ly Logo

Jata VIN145 Manual

0.0 · 0 Ratings

PDF manual · 28 Pages

English

M: OA-GPT-54-NAN
page

/ 28

Loading...
34943797d4437f78ff5e682402a1f7dcd2c6 page d
13
Maximum power function:
• Inthisfunctionyoucansettheoperatingtime,butyoucannotadjustthetemperature,sinceitisxed.
• Press“Preset tiempo”.Thedisplaywillstartblinking.
• Press“+or-”toadjust.
• Once the time has been set, it will be xed in a few seconds. The display will stop blinking.
• Youcanstoptheoperationbypressing“Pausa”.
• Toresume,pressagain.
• Itmustbetakenintoaccountthatthedevicewillautomaticallyswitchoafterpassingthetimeshowninthe
displayoncepressed“Pausa”.
• Toturnotheunitpress anddisconnectitfromthenetwork.
• Ifanerrorcodeappearsonthedisplay,refertothetable:
Trouble code Possible Reasons Solutions
E0 -Nopot/panontheplate;
-Non-usablePansontheplate.
-DiameterofPotissmallerthan120mm.
Putsuitablecookingutensilsontheplate.
E1 -IGBTElectrocircuitmulfunction.
-IGBTsensorisinopencircuitorinshort
circuit.
Pleasecontactthesupplierorgotoa
qualiedservicecenter.
E2 -Temperaturesensorfailure(inopencircuit
orinshortcircuit).
Pleasecontactthesupplierorgotoa
qualiedservicecenter.
e3 -Abnormalsupplyvoltage:voltagetoolow
(<80V).
Pleasecheckpowersupply,poweronafter
powersupplyisbacktonormal.
e4 -Abnormalsupplyvoltage:voltagetoo
high(>280V).
Pleasecheckpowersupply,poweronafter
powersupplyisbacktonormal.
e6 -Platesurfacetemperaturetoohigh.
-Emptypot/panheatingleadstotoohigh
temperature.
Pleasewaitforsomeminutesuntilthecools
down.
Pleasecheckpot/pan.
E7 -Thermalresistordoesn’twork. Pleasecontactthesupplierorgotoa
qualiedservicecenter.
-WhenE3orE4appears,devicewillautomaticallystopheatingbutdonotshutdown.
-WhenotherTroubleCodeappear,devicewillautomaticallystopheatingandshutdown.
Youcouldpress
functiontorestartthedeviceandeliminatetheTroubleCode.
MAINTENANCE AND CLEANING
• Beforeyouproceedtocleaning,unplugtheappliancefromthemainsandwaituntiltheplateistotallycold.
• Youcancleanthebodywithaslightlydampenedcloth.
• Tocleantheplateitisenoughtouseaslightlydampenedclothwithsoap.Youalsocancleantheplatewith
specialproductstocleanvitroceramicplates.
• Iftherearesomehardresiduesyoucanuseascrapersuitableforvitroceramichobs.
• Donotuseabrasiveorchemicalproducts,metallicscourers,andsuchmaydeterioratethesurfaces.
ENVIRONMENT PROTECTION
• Disposetheapplianceaccordingtothelocalgarbageregulations.
• Neverthrowitawaytotherubbish.Soyouwillhelptotheimprovementoftheenvironment.
01 manual jata VIN145.indd 13 27/03/17 12:34

Chat with your Jata VIN145 manual using AI

Get instant AI answers from your Jata VIN145 manual

Ask anything about the Jata VIN145. Answers come from this manual, with the pages they are based on.

VIN145 Maintenance Schedule

After each use
Clean the cooktop surface

Unplug the appliance and wait until the plate is cold. Wipe with a damp cloth and soap or special ceramic cleaner. Use a scraper for stubborn residues.

Show in the manual (page 13)
After each use
Clean the body of the appliance

Wipe the body with a slightly dampened cloth after unplugging and cooling down.

Show in the manual (page 13)
When needed
Replace damaged power cord

If the cable deteriorates, it must be replaced by an authorized service center only.

Show in the manual (page 13)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend VIN145?

Yes No

Frequently Asked Questions

A

The Jata VIN145 is rated at **2100 W** and operates on **220-240 V~ at 50/60 Hz**. This single induction zone is intended for household countertop cooking with quick heat-up and responsive control through its slider and preset time functions.

Is this answer helpful?

A

You must use **induction-compatible cookware** with a **flat base**. The manual warns that if the pot is not suitable for induction or its diameter is too small, the cooktop can show **E0** and disconnect. It also states that diameter below **120 mm** can trigger E0.

Is this answer helpful?

A

No. For **saute, fry, and stew**, you can set a default time using **Preset time** and adjust temperature with the slider/power levels. For **minimum power, broth, steam, and boiling**, time and temperature cannot be adjusted, but you can program the **start** using Preset time. **Maximum power** allows time but keeps temperature fixed.

Is this answer helpful?

A

**E0** indicates that the cooktop is not detecting a valid pot. The manual lists likely causes as: no pot on the plate, a pot not compatible with induction, or a pot diameter below **120 mm**. The solution is to place suitable cookware centered on the plate.

Is this answer helpful?

A

During operation, you can stop the process by pressing **Pause**. To resume, press **Pause** again. The manual also notes that the appliance may disconnect automatically after the time displayed has elapsed, depending on the mode.

Is this answer helpful?

A

Unplug the unit and wait until the plate is completely cold. Clean the body with a slightly damp cloth. For the plate, a damp cloth with a bit of soap is usually enough, and you can use products intended for **vitroceramic** surfaces. If residues remain, use a suitable scraper. Avoid abrasive chemicals, metal scourers, and harsh cleaners.

Is this answer helpful?

A

No. The manual states that the appliance is not intended to operate through an **external timer** or a separate **remote control system**. Control is meant to be done directly on the unit.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Induction cooking with a 2100 W single-zone design for efficient countertop meals.
  • Multiple pre-set programs (minimum, broth, steam, saute, fry, stew, maximum power).
  • Clear display and straightforward controls, including Preset time and Pause.
  • Cookware detection with error code E0 for missing or incompatible pots.
  • Easy care: body wipes with a damp cloth; plate cleaning supports vitroceramic products.
VS

Disadvantages

  • Only works with induction-compatible cookware and may require a pot diameter of 120 mm or more.
  • Some programs restrict user control of time and temperature by design.
  • Single-zone format limits simultaneous cooking compared with multi-burner hobs.
  • Error conditions may stop heating automatically, requiring the correct cookware or troubleshooting.
M: OA-GPT-54-NAN

Product Specification

Power

2100 W

Design

black, glass ceramic surface

Width

13.39 in

Cooking zones

1 cooking zone, of which 1x cooking zone diameter 10.24 in (2200/3700 W)

Temperature control

176-464°F

Control

Touch control

Features

Pot detection, Timer, Safety shut-off

M: GO-GEM-FL-25

Product Description

Jata VIN145 Single Induction Cooktop Freestanding Manual

If you want fast, controlled cooking without installing a full hob, the Jata VIN145 Single Induction Cooktop Freestanding Manual is designed for everyday home use. It is a single-zone induction cooker (Model VIN145) with a 2100 W output, running on 220-240 V~ at 50/60 Hz, and it brings a modern, easy-to-read control layout with a display, a slider regulator, and dedicated buttons for selection, preset time, and pause.

Cooking programs for real-life meals

The VIN145 includes several pre-set programs you can cycle through using the selection button. Depending on the mode, you can fine-tune the cooking experience:

  • Minimum power, broth, steam, and boiling are designed with fixed time and temperature behavior, while still letting you program the start using Preset time.
  • Saute, fry, and stew let you set a default operating time with Preset time, then adjust temperature using the slider and power levels.
  • Maximum power keeps temperature fixed, while allowing you to set the operating time. You can pause and resume, and the unit will also follow its programmed shutdown logic.

To help protect the cooking process, the cooktop can detect incompatible cookware. If no suitable pot is present, the display shows E0 and the unit disconnects after a short moment. The manual indicates that cookware should be induction-compatible with a flat base, and if the pot diameter is below 120 mm, E0 may appear.

Notes on setup, safety, and usability

For best results, place the cooktop on a flat, heat-resistant surface and position the pot in the center of the plate. Keep the appliance away from curtains and flammable materials, and never immerse the main body or cable in water. The manual also highlights that hot surfaces are normal during use, that children should be supervised, and that the cooker should not run unattended.

Key results

  • 2100 W induction performance with a single, focused cooking zone for flexible countertop cooking.
  • Multiple cooking programs: minimum, broth, steam, saute, fry, stew, and maximum power.
  • Preset time control, plus pause/resume options depending on the selected mode.
  • Built-in cookware detection with error codes like E0 for missing or incompatible pots.

What to watch

  • Requires induction-compatible cookware; small-diameter or non-compatible pans trigger E0.
  • Not all modes allow manual temperature or time changes; some functions are intentionally fixed.
  • Hot-surface caution and strict placement rules are essential to safe operation.

Maintenance tips

Unplug the unit and wait for the plate to cool fully before cleaning. Use a damp cloth for the body, and for the plate use a damp cloth with mild soap or products suitable for vitroceramic surfaces. For stubborn residue, use a suitable scraper, and avoid abrasive chemicals or metal scourers.

M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly