Manual.ly Logo

Holzmann TS200 Manual

4.0 · 1 Ratings

PDF manual · 63 Pages

English

M: OA-GPT-54-NAN
page

/ 63

Loading...
1ea150ab966b55d4d3b45a8564bb9f62422c page 1b
WARTUNG UND PFLEGE
HOLZMANN Maschinen Austria www.holzmann-maschinen.at Seite 27
Tischkreissäge / table saw TS 200 / TS 250
8.1 Sägeblattwechsel
ACHTUNG: Bei Montage und Sägeblatt- Wechsel immer Schutzhandschuhe verwenden !
Das Sägeblatt auf max. Höhe einstellen.
Die 2 Inbusschrauben am Tischeinsatz herausschrauben und den Tischeinsatz entnehmen.
Das Sägeblatt am Flansch mit dem mitgelieferten Flanschschlüssel fixieren.
Die Schraube mit einem Werkzeugschlüssel SW13 nach links aus der Welle schrauben.
Reinigen Sie die Motorspindel und den Flansch gründlich von Verunreinigungen.
Setzen Sie das Sägeblatt mit der richtigen Drehrichtung auf die Motorspindel.
Den gereinigten Flansch mit Zapfen in die Bohrung auf die Motorwelle setzen.
Die Schraube mit Beilagscheibe wieder in die Welle schrauben und mit Flanschschlüssel und
Werkzeugschlüssel festschrauben.
HINWEIS: Drehrichtungs-Pfeil auf Sägeblatt beachten.
Tischeinsatz wieder einlegen und festschrauben
8.2 Reinigung
HINWEIS
Der Einsatz von Lösungsmitteln, aggressiven Chemikalien oder Scheuermitteln führt zu
Sachschäden an der Maschine!
Daher gilt: Bei der Reinigung nur Wasser und ggf. milde Reinigungsmittel verwenden.
Blanke Flächen der Maschine gegen Korrosion imprägnieren (z.B. mit Rostschutzmittel WD40)
8.3 Instandhaltung
Alle Teile (außer dem Lager des Hauptsägedorns) sollten zweimal wöchentlich geschmiert werden.

Chat with your Holzmann TS200 manual using AI

Get instant AI answers from your Holzmann TS200 manual

Ask anything about the Holzmann TS200. Answers come from this manual, with the pages they are based on.

TS200 Maintenance Schedule

Twice weekly
Lubricate moving parts

Lubricate all parts except the main saw mandrel bearings twice a week to ensure smooth operation.

Show in the manual (page 27)
After each shift
Clean the machine and parts

Thoroughly clean the machine after each shift by sucking dust and swarf through the suction system and removing other waste with compressed air.

Show in the manual (page 26)
Regularly
Check safety signs

Check regularly that warning and safety instructions on the machine are present and in perfectly legible condition.

Show in the manual (page 26)
Before every use
Inspect safety devices

Check before every operation that all safety devices are in perfect working condition.

Show in the manual (page 26)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend TS200?

Yes No
0
User Pic

Tim Klein

9 months ago

The assembly instructions seem incomplete. I could not find the manual until after removing the saw from the small pallet compartment, and the steps for connecting the dust extraction hose under the circular saw are missing. Is there guidance for that?

0
User Pic

Manual.ly

9 months ago

Thanks for your feedback. The manual may be packed in the housing cavity underneath the protective wood compartment, so it is easy to miss before the saw is removed. For dust extraction, please follow the section on connecting the suction hose to the outlet below the saw and then to the matching dust-collection box. If your printed guide does not include those steps, contact our support with your order number and model (e.g., the TS 250-related setup is comparable). We can provide a clearer step-by-step reference or an updated instruction sheet. You can also use the official video resources as an orientation until you receive the corrected guidance.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It is designed for wood-based materials such as solid wood, chipboard, and veneered panels. It is not meant for metal, masonry, or other unsuitable materials.

Is this answer helpful?

A

Yes. The blade can be tilted from 90° down to 45°, which allows you to make angled cuts for a variety of woodworking projects.

Is this answer helpful?

A

The saw provides dust extraction connections, helping you connect it to an external extraction system and keep the work area cleaner during operation.

Is this answer helpful?

A

The maximum cutting width is listed at up to 750 mm, which gives you enough range for many common boards and panel-cutting tasks.

Is this answer helpful?

A

Check the blade guard, riving knife, fence alignment, grounding, and workpiece support. Always disconnect power before adjustments or maintenance.

Is this answer helpful?

A

Cleaning should be done after use, and moving parts should be lubricated regularly. The blade should be checked often and replaced when dull or damaged.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 230V motor and 200 mm blade deliver practical cutting power for common woodworking jobs.
  • Sliding table and rip fence improve feed control and cutting accuracy on larger pieces.
  • Blade height and tilt adjustments add flexibility for straight and angled cuts.
  • Built-in safety features support safer operation when used correctly.
VS

Disadvantages

  • Assembly and alignment take time and require careful setup before use.
  • Best results depend on sharp blades and regular maintenance.
  • Not intended for outdoor or wet environments.
  • Narrow cuts require extra care and a push stick for safer feeding.
M: OA-GPT-54-NAN

Product Specification

Type

Table saw

Power

1100 W (230 V)

No-load speed

4,700/min

Saw blade diameter

7.87 in

Cutting capacity

2.36 in (cutting depth at 0 deg), 1.57 in (cutting depth at 45 deg tilt)

Blade tilt

0-45 deg

Special features

Parallel fence, Miter fence, Dust extraction, Miter function, Tilt function

Weight

165.35 lb

Scope of delivery

Table extension

M: OA-GPT-54-NAN

Product Description

Holzmann TS200 Electric Table Saw

The Holzmann TS200 Electric Table Saw is a compact but capable workshop machine designed for accurate woodworking tasks. Built for cutting solid wood, chipboard, veneered panels, and similar sheet materials, it combines practical handling with solid safety-minded construction. If you are looking for a machine that supports straight rip cuts, angle cuts, and cleaner control over longer workpieces, the TS200 offers a well-balanced set of features for home workshops and professional light-duty use.

At the heart of the machine is a 230V motor paired with a 200 mm saw blade, delivering fast cutting action and dependable performance for everyday tasks. The table layout includes a rip fence, sliding table, height adjustment, and tilt adjustment from 90° to 45°, making it easier to handle both standard crosscut-style work and angled cuts. With a maximum cutting width of up to 750 mm, the saw is suited to a wide range of woodworking projects.

One of the strongest points of the TS200 is its focus on control. The parallel fence helps guide the material accurately, while the sliding table improves feed stability and makes larger pieces easier to manage. Dust extraction support also helps keep the working area cleaner, which is especially useful during longer cutting sessions. For users who value a tidy and more efficient workspace, this is a meaningful advantage.

Safety is clearly a priority in the Holzmann TS200 Electric Table Saw Manual, and that approach is reflected in the machine design. The riving knife, blade guard, emergency stop function, and grounding instructions all work together to reduce risk during operation. The manual also emphasizes proper blade condition, correct workpiece feeding, and the use of a push stick for narrow cuts. These details show that the saw is built not only for performance, but also for disciplined and careful use.

Assembly and setup are more involved than on a basic saw, but the structure is straightforward once the parts are mounted and aligned. The machine is designed to be leveled, connected to extraction, and checked carefully before first use. Regular maintenance is equally important, especially cleaning, blade replacement, and lubrication of moving parts.

Notes

  • Use only the correct blade size and keep it sharp.
  • Adjust the riving knife and fence before cutting.
  • Wear proper protective gear and connect the saw to a grounded outlet.
  • Keep the working area clear and support long stock properly.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly