Manual.ly Logo

Heco In Vita 3 Manual

0.0 · 0 Ratings

PDF manual · 44 Pages

English

M: QW-35-FL
page

/ 44

Loading...
09ff1577c4f2f0869cc641685dd3d2e0e872 page 7
Dear HECO Customer,
Congratulations on your fine new loudspeakers and thank you very much for choosing HECO! You have
made an excellent choice. The high-quality speakers produced by HECO are renowned all over the
world. Please study the instructions and information below carefully before using your new loudspeakers.
FITTING THE FEET (IN VITA 9 ONLY)
The (2) feet included in the delivery package must be fitted to the loudspeaker before use. To do this,
place the speakers on a clean, stable base with the bottom facing upwards. It is better not to remove
the protective bag until after fitting has been completed so as to avoid damage to the paint surface.
Fit the two pre-assembled feet using the M6 screws provided, as shown in Fig. 1.
The metal spikes (x) are height-adjustable so as to guarantee the stability of the speaker. To do this,
loosen the top lock nut (y) and adjust the spike by turning it. Once the right setting has been found,
tighten the lock nut again.
Rubber inserts are screwed into the bottom of the cone spikes. These ensure optimum stability on
smooth, hard floor coverings, such as laminate or tiles. The rubber inserts can be replaced with metal
inserts (included in the package). This variation is better suited for carpets, for example.
GENERAL INFORMATION ABOUT CONNECTING YOUR HECO IN VITA LOUDSPEAKERS
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent
impairment of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths
up to 3 m and at least 4 mm² for lengths above 3 m.
Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place
the loudspeakers in their planned positions and cut the cables to the right length. The cables for both
channels should always be exactly the same length.
Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than
tinning them with solder – insert them in the terminals and tighten the terminal screws firmly. (Fig. 2)
For good sound it is imperative that the cables must be connected in such a way that the speakers are “in
phase”. This means that the black negative terminals on the speakers (-) must be connected to the negative
(-) terminals on the amplifier, the red positive (+) speaker terminals to the positive (+) amplifier terminals. To
make this easier one wire of most speaker cables is marked with a coloured strip or a ridge in the insulation.
Before switching on the system double-check all your connections and make sure that the terminal
screws are tight and that there are no short circuits caused by stray wire filaments – this could cause
serious damage to your amplifier!
THE HECO IN VITA LOUDSPEAKERS IN STEREO MODE
In the ideal configuration the speakers and the listening position should form an equilateral triangle.
When the left and right speakers are the same distance from the listening position their sound arrives at
the same time, resulting in a harmonious, natural music reproduction. (Fig. 3)
There should be a clear line of sight between the loudspeakers and the listening position. Any sound-
absorbing or reflecting obstacles in the path will distort the sound. When you install the loudspeakers
the following distances should be maintained:
Floorstanders: at least 20 cm away from the rear wall and at least 30 cm from the side walls. This will
prevent excessive emphasis of the bass range.
Bookshelf speakers: shelf loudspeakers should also be as free-standing as possible, the distance to the
sides and rear to walls and items should be at least 10 cm, the tweeters should be located at ear height.
7

Chat with your Heco In Vita 3 manual using AI

Get instant AI answers from your Heco In Vita 3 manual

Ask anything about the Heco In Vita 3. Answers come from this manual, with the pages they are based on.

In Vita 3 Maintenance Schedule

As needed
Clean the cabinet surface

Clean the housing with a mild household cleaner. Do not use furniture polish or similar products.

As needed
Check for amplifier distortion

Monitor volume levels for audible distortion and immediately reduce volume if detected to protect speakers from damage.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend In Vita 3?

Yes No

Frequently Asked Questions

A

Always disconnect the amplifier before connecting cables to prevent short circuits. Use high quality speaker cables with the proper cross-section based on length. Twist the ends instead of soldering them. Ensure the black negative terminal connects to negative and red positive to positive for correct phase alignment.

Is this answer helpful?

A

For lengths under three meters, a cross-section of at least 2.5 mm squared is recommended. For cable lengths exceeding three meters, you should use cables with a cross-section of at least 4 mm squared to maintain signal integrity without degradation.

Is this answer helpful?

A

Yes, the five terminal screws facilitate bi-wiring connections. The upper terminals are connected to the treble and mid-treble side, while the lower terminals are connected to the bass side. You must remove the metal bridges to enable bi-wiring mode for separate cables.

Is this answer helpful?

A

Clean the exterior surfaces using mild household cleaners and soft cloths. You should never use furniture polish or similar products as these can damage the finish permanently and lead to appearance degradation over time or attract dust particles.

Is this answer helpful?

A

Amplifiers, tuners, and CD players can produce inaudible high-frequency signals that might harm tweeters. If tweeters fail at low volumes, have a qualified technician check your system components for dangerous inaudible signals or oscillations before continuing use.

Is this answer helpful?

A

For floorstanders, maintain at least 20 cm from the rear wall and 30 cm from side walls. Bookshelf speakers should also have at least 10 cm from walls and obstacles. This prevents excessive bass and ensures proper sound dispersion.

Is this answer helpful?

A

Bi-amping uses separate power amplifiers and cables for high and low frequencies. It can improve sound reproduction quality significantly. However, it requires additional equipment and removing the bridge terminals for proper configuration during setup.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High quality sound engineering with worldwide recognition for reliability.
  • System supports bi-wiring and bi-amping for superior audio fidelity.
  • Five terminal screws offer flexible connection options and settings.
  • Adjustable spikes ensure stability and reduce unwanted resonance issues.
  • Clear instructions help maximize investment without technical knowledge.
VS

Disadvantages

  • Requires a separate amplifier for bi-amping mode to function properly.
  • Specific high quality cabling needed to prevent signal loss effectively.
  • Tweeters can be damaged by weak amplifiers causing distortion quickly.
  • Floor standing models require separate feet installation for stability.
  • Manual provided in many languages which might cause confusion.
M: QW-35-FL

Product Specification

Type

Compact Speaker

Principle

2-Way

Tweeter

1x 1.10"

Woofer

1x 6.70"

Frequency Range

30 Hz - 43 kHz

Power Handling

90 W RMS, 160 W Peak

Impedance

4-8 Ohms

Sensitivity

90 dB

Special Features

Bi-Wiring

Dimensions (WxHxD)

8.07x14.84x13.11 in

M: QW-35-FL

Product Description

Heco In Vita 3 Audio System Review

Welcome to the world of high-fidelity audio with the Heco In Vita 3. This product represents a commitment to sound engineering that has gained worldwide recognition for its reliability and performance standards in modern audio systems. When you invest in this speaker, you are choosing a quality product designed for exceptional performance in various listening environments regardless of room size. Understanding the intricacies of your new equipment is vital for optimal listening experiences, which is why familiarizing yourself with the essential information provided in the official guide is paramount for safety. The Heco In Vita 3 Manual offers crucial insights into maximizing your investment and ensuring safety during operation without requiring extensive technical knowledge.

Setup And Placement

Setting up these speakers requires attention to detail and patience to achieve best results in your home theater. While specific stands are required for larger models, the In Vita 3 bookshelf variant benefits significantly from being placed on stable surfaces away from walls to reduce reflections. Aiming for an equilateral triangle between the speakers and your listening position creates the ideal soundstage for stereo playback. This geometry ensures acoustic signals arrive simultaneously, producing a harmonious and balanced audio image that respects the original recording intent without phase cancellation issues or frequency gaps.

Connection Details

Connectivity is another critical aspect of achieving good sound quality consistently over long distances. Using high-quality speaker cables prevents unnecessary signal loss over distance or interference. For lengths under three meters, a cross-section of at least 2.5 mm squared is recommended to maintain impedance control effectively. Longer runs require 4 mm squared to maintain signal integrity without degradation of audio fidelity or power delivery. Always disconnect amplifiers before connecting cables to prevent potential short circuits that could damage expensive electronics components immediately. Ensure black terminals match negative and red match positive for correct phase alignment throughout the system.

Advanced Features

The In Vita 3 system supports bi-wiring and bi-amping, allowing advanced users to separate frequency ranges for potentially superior audio fidelity and clarity in complex setups. The five terminal screws facilitate these connections, offering flexibility with a +2dB treble boost option for rooms with heavy damping or acoustic treatments reducing bass energy. Maintaining a clear line of sight between speakers and listener avoids sound distortion caused by obstacles or furniture placement blocking the sound path or absorbing frequencies.

Maintenance And Care

Care is straightforward but non-negotiable for longevity of the unit and preserving the finish appearance. Clean the cabinets with mild household cleaners only on exterior surfaces using soft cloths. Avoid furniture polish which can damage the finish permanently and degrade appearance over time or attract dust particles. Be mindful of amplifier power settings matching the speaker capabilities to prevent voice coil damage during high volume usage. Overdriving speakers with mismatched power settings can lead to physical destruction of driver units or thermal failure. Watch for distortion and reduce volume immediately if audible clipping occurs during playback sessions to protect the tweeters.

Troubleshooting

Environmental factors also play a role in failure prevention regarding electronics quality and safety. Amplifiers and sources can sometimes produce inaudible high-frequency signals that might harm tweeters if volumes are kept high without warning signs or protection circuits. If issues arise at low volumes, have a technician check the system components for dangerous oscillations before further use. By following these guidelines, you ensure longevity and pristine sound quality throughout the ownership period. The Heco In Vita 3 Manual serves as your roadmap to unlocking the full potential of these loudspeakers safely and effectively for years. Enjoy the listening journey with confidence knowing your system is set up correctly according to manufacturer standards. This dedication to proper installation guarantees that every note plays out with clarity and precision.

M: QW-35-FL

© Copyright 2026 Manual.ly