Manual.ly Logo

Heco Celan Revolution Center 4 Manual

0.0 · 0 Ratings

PDF manual · 56 Pages

English

M: QW-35-FL
page

/ 56

Loading...
bc0f56ec97e01e69871bc33b40170be4d33f page 8
8
Dear HECO Customer,
Congratulations on your ne new loudspeakers and thank you very much for choosing HECO! You
have made an excellent choice. The high-quality speakers produced by HECO are renowned all over
the world.
Please study the instructions and information below carefully before using your new loudspeakers.
FITTING THE FEET (CELANREVOLUTION 9 AND 7)
The (2) feet included in the delivery package must be tted to the loudspeaker before use. To do this,
place the speakers on a clean, stable base with the bottom facing upwards. It is better not to remove
the protective bag until after tting has been completed so as to avoid damage to the paint surface.
First t the four metal spikes to the two metal traverses, as shown in Fig. 1: Two spikes each (x) are
screwed into the threaded holes in the traverses (w) from below as far as they will go. The lock screw
(z) is then tted and tightened.
Now t the two pre-assembled feet using the M6 screws provided, as shown in Fig. 1.
The metal spikes (x) are height-adjustable so as to guarantee the stability of the speaker. To do this,
loosen the top lock nut (z) and adjust the spike by turning it. Once the right setting has been found,
tighten the lock nut again.
Rubber inserts are screwed into the bottom of the cone spikes. These ensure optimum stability on
smooth, hard oor coverings, such as laminate or tiles. The rubber inserts can be replaced with metal
inserts (included in the package). This variation is better suited for carpets, for example.
GENERAL INFORMATION ABOUT CONNECTING YOUR HECO CELANREVOLUTION LOUDSPEAKERS
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent
impairment of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for lengths
up to 3 m and at least 4 mm² for lengths above 3 m.
Always turn off the amplier or receiver before connecting or disconnecting loudspeaker cables. Place
the loudspeakers in their planned positions and cut the cables to the right length. The cables for both
channels should always be exactly the same length.
Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than
tinning them with solder – insert them in the terminals and tighten the terminal screws rmly. (Fig. 2)
For good sound it is imperative that the cables must be connected in such a way that the speakers are
“in phase”. This means that the black negative terminals on the speakers (-) must be connected to the
negative (-) terminals on the amplier, the red positive (+) speaker terminals to the positive (+) amplier
terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a
ridge in the insulation.
Before switching on the system double-check all your connections and make sure that the terminal
screws are tight and that there are no short circuits caused by stray wire laments – this could cause
serious damage to your amplier!

Chat with your Heco Celan Revolution Center 4 manual using AI

Get instant AI answers from your Heco Celan Revolution Center 4 manual

Ask anything about the Heco Celan Revolution Center 4. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Celan Revolution Center 4?

Yes No

Frequently Asked Questions

A

Place the speaker directly below your television. Ensure the tweeter is at ear level when you are seated in your primary listening position to create an accurate sound stage.

Is this answer helpful?

A

Yes, the speaker has five terminals that allow for bi-wiring and bi-amping. You must remove the factory metal bridges to enable these advanced connection methods for improved sound quality.

Is this answer helpful?

A

The speaker ships with rubber spikes installed, which are perfect for hard surfaces like tile or laminate. Metal spikes are included in the box for use on carpeted floors.

Is this answer helpful?

A

By default, the +2dB treble boost is active via a metal bridge. To switch to a linear setting, unscrew the corresponding terminals and remove the bridge. Reverse this process to re-enable the boost.

Is this answer helpful?

A

For cable lengths up to 3 meters, use a minimum cross-section of 2.5 mm². For longer runs, we recommend using cables with at least 4 mm² to prevent sound loss.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Seamlessly matches the look and sound of the rest of the CELAN REVOLUTION series
  • Supports bi-wiring and bi-amping for enhanced audio separation
  • Includes adjustable treble boost (+2dB) for different room acoustics
  • Versatile spike options with interchangeable rubber and metal inserts
VS

Disadvantages

  • Requires separate purchase of high-quality speaker cables
  • Rubber spikes may not be ideal for thick carpets without replacement
  • No built-in subwoofer output, requiring external crossover setup for full range
M: QW-35-FL

Product Specification

Type

Center speaker

Principle

2-way

Tweeter

1x 1.20"/30.5mm

Woofer

2x 7"/177.8mm

Frequency range

30Hz-52kHz

Power handling

120W RMS, 180W Peak

Impedance

4-8Ω

Sensitivity

90dB

Features

Bi-Wiring

Dimensions (WxHxD)

23.54x8.35x14.17in

Weight per piece

33.07lb

M: QW-35-FL

Product Description

Experience Perfect Dialogue with the Heco Celan Revolution Center 4

The Heco Celan Revolution Center 4 stands as a cornerstone for any high-fidelity home theater system. Designed to seamlessly match the visual and acoustic characteristics of the broader CELAN REVOLUTION series, this center speaker ensures that dialogue remains clear, precise, and immersive. Positioned directly beneath your television, it anchors the soundstage, delivering vocals that are perfectly integrated with front left and right channels.

This two-way bass reflex design is engineered for versatility and performance. It handles power loads ranging from 30 to 180 watts, making it compatible with a wide array of amplifiers. The frequency response spans from 30 Hz to 52,000 Hz, capturing every nuance of speech and subtle sound effects without distortion. Its impedance of 4 to 8 ohms allows for easy connection to most modern receivers.

Installation is straightforward yet customizable. The unit comes equipped with rubber spikes designed for smooth, hard floors like laminate or tile, ensuring stability and reducing unwanted resonance. For carpeted rooms, these can be swapped for metal inserts included in the package to prevent sinking and maintain optimal positioning. The speaker features five screw terminals on the rear panel, supporting conventional wiring as well as advanced bi-wiring and bi-amping configurations. This flexibility allows audiophiles to optimize signal separation between high and low frequencies for superior clarity.

A unique feature of the Heco Celan Revolution Center 4 is the adjustable treble boost. A factory-installed metal bridge activates a +2dB treble setting by default, which is ideal for acoustically deadened rooms filled with heavy furniture or curtains. Removing the bridge switches the speaker to a linear response for those who prefer a flatter sound signature. Proper placement involves aligning the tweeter at ear level when seated, creating an equilateral triangle with your listening position and main speakers for the most natural sound image.

Maintaining the speaker is simple; a mild household cleaner is sufficient to wipe down the cabinet, while furniture polish should be strictly avoided to protect the finish. By combining robust build quality with intelligent design, the Heco Celan Revolution Center 4 delivers a cinematic experience that brings movies and music to life.

Important Notes

  • Always turn off your amplifier before connecting or disconnecting cables to prevent damage.
  • Ensure all wire connections are tight to avoid short circuits which can harm your amplifier.
  • Use speaker cables with a cross-section of at least 2.5 mm² for lengths up to 3 meters.
M: QW-35-FL

© Copyright 2026 Manual.ly