Manual.ly Logo

Heco Aurora 1000 Manual

0.0 · 0 Ratings

PDF manual · 52 Pages

English

M: QW-35-FL
page

/ 52

Loading...
b409a3e0faf035cbd28b126cfa5b5d565fc9 page 8
Dear HECO Customer,
Congratulations on your fine new loudspeakers and thank you very much for choosing HECO! You
have made an excellent choice. The high-quality speakers produced by HECO are renowned all over
the world.
Please study the instructions and information below carefully before using your new loudspeakers.
FITTING THE FEET (AURORA 1000 AND 700 ONLY)
The 2 feet included in the delivery package must be fitted to the loudspeaker before use. To do this,
place the speakers on a clean, stable base with the bottom facing upwards. It is better not to remove
the protective bag until after fitting has been completed so as to avoid damage to the paint surface.
First fit the four metal spikes to the two traverses, as shown in Fig. 1: Two spikes each (x) are
screwed into the threaded holes in the traverses (w) from below as far as they will go. From above,
the lock screw (z) is then fitted and tightened.
Now fit the two pre-assembled feet using the M6 screws provided, as shown in Fig. 1.
The metal spikes (x) are height-adjustable so as to guarantee the stability of the speaker. To do this,
loosen the top lock nut (z) and adjust the spike by turning it. Once the right setting has been found,
tighten the lock nut again.
Rubber inserts are screwed into the bottom of the cone spikes. These ensure optimum stability on
smooth, hard floor coverings, such as laminate or tiles. The rubber inserts can be replaced with metal
inserts (included in the package). This variation is better suited for carpets, for example.
GENERAL INFORMATION ABOUT CONNECTING YOUR HECO AURORA LOUDSPEAKERS
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent
impairment of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for
lengths up to 3 m and at least 4 mm² for lengths above 3 m.
Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables.
Place the loudspeakers in their planned positions and cut the cables to the right length. The cables
for both channels should always be exactly the same length.
Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than
tinning them with solder – insert them in the terminals and tighten the terminal screws firmly. (Fig. 2)
For good sound it is imperative that the cables must be connected in such a way that the speakers
are “in phase”. This means that the black negative terminals on the speakers (-) must be connected
to the negative (-) terminals on the amplifier, the red positive (+) speaker terminals to the positive (+)
amplifier terminals. To make this easier one wire of most speaker cables is marked with a coloured
strip or a ridge in the insulation.
Before switching on the system double-check all your connections and make sure that the terminal
screws are tight and that there are no short circuits caused by stray wire filaments – this could cause
serious damage to your amplifier!
THE HECO AURORA LOUDSPEAKERS IN STEREO MODE
In the ideal configuration the speakers and the listening position should form an equilateral triangle.
When the left and right speakers are the same distance from the listening position their sound arrives
at the same time, resulting in a harmonious, natural music reproduction. (Fig. 3)
There should be a clear line of sight between the loudspeakers and the listening position. Any sound-
absorbing or reflecting obstacles in the path will distort the sound. When you install the loudspeakers
the following distances should be maintained:
8
Aurora_LS_Manual.indd 8 11/14/2017 9:20:20 AM

Chat with your Heco Aurora 1000 manual using AI

Get instant AI answers from your Heco Aurora 1000 manual

Ask anything about the Heco Aurora 1000. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Aurora 1000?

Yes No

Frequently Asked Questions

A

Place the speaker at least 20 cm from the back wall and 30 cm from side walls. Ensure the speaker and listening position form an equilateral triangle for optimal stereo imaging.

Is this answer helpful?

A

Yes, the terminals support bi-amping. Remove the factory metal bridges between positive and negative terminals and use separate amplifiers for high and low frequencies.

Is this answer helpful?

A

Use high-quality cables with at least 2.5 mm2 cross-section for lengths up to 3 meters. Longer runs require at least 4 mm2 to prevent sound loss.

Is this answer helpful?

A

Clean with a mild household cleaner. Do not use furniture polish or similar products as they can damage the lacquered surface permanently over time.

Is this answer helpful?

A

The Heco Aurora 1000 works best with amplifiers delivering between 30 and 380 watts to ensure linear reproduction and avoid distortion or damage.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High efficiency rating of 93 dB ensures powerful sound output
  • Supports bi-wiring and bi-amping for enhanced audio separation
  • Adjustable spikes allow for flexible placement on various floor types
VS

Disadvantages

  • Large dimensions require significant space in the listening room
  • Requires external amplifier with sufficient power to handle load
  • Complex wiring setup if not using conventional connection method
M: QW-35-FL

Product Specification

Type

Floorstanding Speaker

System

3-Way

Tweeter

1x 1.10"

Midrange

1x 6.70"

Woofer

2x 7.90"

Frequency Range

22Hz-42kHz

Power Handling

230-380W

Impedance

4-8Ohm

Dimensions (WxHxD)

12.01x49.53x15.47in

Weight per Unit

58.64lbs

M: QW-35-FL

Product Description

Elevate Your Audio Experience with Heco Aurora 1000

Welcome to the world of premium sound when you select the Heco Aurora 1000. This floorstanding speaker delivers exceptional fidelity suited for demanding audiophiles. It combines robust engineering with elegant aesthetics to fill your room with rich, clear audio. The three-way bass reflex configuration allows deep lows and crisp highs to coexist harmoniously without compromise. Proper placement from the Heco Aurora 1000 Manual is critical for achieving the best results from this high-performance unit available on the market today.

When setting up your system, positioning impacts sound quality significantly. Position the speaker at least twenty centimeters from the rear wall to prevent excessive bass resonance. Maintain a distance of thirty centimeters from side walls to ensure a balanced soundstage. The included metal spikes detach the speaker from the floor, reducing unwanted vibrations. You can swap between metal and hard rubber inserts depending on your specific flooring type.

Connectivity options are versatile for advanced setups. The terminals support conventional wiring, bi-wiring, and bi-amping modes effectively. For bi-amping, remove the factory metal bridges connecting the positive and negative terminals. This setup ensures high and low frequencies travel on separate circuits for superior performance. Always turn off your amplifier before making these connections to protect your gear from power surges. Use high-quality speaker wires with a cross-section of at least 2.5 mm2 for lengths up to three meters.

Stereo mode requires the speakers and listening position to form an equilateral triangle. This guarantees acoustical signals arrive simultaneously for a natural image. Keep a line of sight between speakers and the listener to avoid distortion from obstacles. Maintenance is straightforward to keep the finish looking pristine. Clean the surface with a mild household cleaner for best results. Avoid using furniture polish as chemicals may damage the paint finish permanently. If tweeters fail at low volumes, check for inaudible high-frequency signals from source components. Pairing the Aurora 1000 with other models in the Heco Aurora series creates a cohesive home theater experience. The Center 30 and Sub 30A complement the main speakers perfectly for cinema simulations.

Important Notes

Check impedance ratings before connecting amplifiers to prevent damage. Ensure your amplifier has sufficient power handling capability for optimal dynamics.

M: QW-35-FL

© Copyright 2026 Manual.ly