Manual.ly Logo

Heco Ambient 11 F Manual

0.0 · 0 Ratings

PDF manual · 44 Pages

English

M: QW-35-FL
page

/ 44

Loading...
463063dc837c01eb75cc9c49cd295308727b page 7
7
Dear HECO Customer,
Congratulations on your ne new loudspeakers and thank you very much for choosing HECO! You
have made an excellent choice. The high-quality speakers produced by HECO are renowned all
over the world.
Please study the instructions and information below carefully before using your new loudspeakers.
GENERAL INFORMATION ABOUT CONNECTING YOUR HECO AMBIENT LOUDSPEAKERS
Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent
impairment of sound quality, we recommend cables with cross-sections of at least 2.5 mm² for
lengths up to 3 m and at least 4 mm² for lengths above 3 m.
Always turn off the amplier or receiver before connecting or disconnecting loudspeaker cables.
Place the loudspeakers in their planned positions and cut the cables to the right length. The cables
for both channels should always be exactly the same length.
Strip 10 – 15 mm of insulation from the ends of the cables. Twist the ends – this is much better than
tinning them with solder – insert them in the terminals and tighten the terminal screws rmly (g. 1 + 2).
Loudspeaker cables with CE-compliant banana or single-pin plugs (4 mm) or forked ttings can
also be used.
For good sound it is imperative that the cables must be connected in such a way that the speakers
are “in phase”. This means that the black negative terminals on the speakers (-) must be connected
to the negative (-) terminals on the amplier, the red positive (+) speaker terminals to the positive (+)
amplier terminals. To make this easier one wire of most speaker cables is marked with a coloured
strip or a ridge in the insulation.
Before switching on the system double-check all your connections and make sure that the terminal
screws are tight and that there are no short circuits caused by stray wire laments – this could
cause serious damage to your amplier!
WALL MOUNTING
The Ambient 11F, 22F and 44F speakers are designed as wall speakers and offer two wall-mounting
options:
1. Attached to the rear are 4 metal xtures that allow the speaker to be hooked onto two screws
tted to the wall. The speakers can be tted to the wall vertically or horizontally. The logo on the
cover frame is tted in such a way that it can be easily turned to match the direction of the speaker.
Figure 5 - 8 provides information about the screw spacing and the screw dimensions.
2. There are 4 additional threaded inserts on the back (centre of the housing), which allow the use
of a VESA standard wall bracket. The hole size is 100 mm x 100 mm, M4 thread.
Important information/safety instructions:
The customer is solely responsible for the use of wall brackets / speakers attachments.
The customer is also solely responsible for the secure attachment of the speaker bracket to the wall
and the selection of suitable mounting material (e.g. screws, wall plugs, etc.), while taking account of
the weight and construction of the speaker and the condition of the wall.

Chat with your Heco Ambient 11 F manual using AI

Get instant AI answers from your Heco Ambient 11 F manual

Ask anything about the Heco Ambient 11 F. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Ambient 11 F?

Yes No

Frequently Asked Questions

A

You can mount it using four metal fixtures on the back for screw attachment or use the four threaded inserts for a VESA standard bracket. It supports both vertical and horizontal orientations.

Is this answer helpful?

A

A recommended amplifier output between 20 and 80 watts ensures optimal performance. Avoid underpowered amps that distort easily or overpowered ones that might damage the drivers.

Is this answer helpful?

A

While possible, the 44F model is better suited for center channel duties due to its larger size and horizontal orientation capabilities. The 11F is primarily designed for front or rear positions.

Is this answer helpful?

A

Use a mild household cleaner on the lacquered surfaces. Do not use furniture polish or microfiber cloths as they can damage the finish.

Is this answer helpful?

A

This could be caused by inaudible high-frequency signals from your amplifier or source components. Have a technician check your system for dangerous oscillations.

Is this answer helpful?

A

Use cables with a cross-section of at least 2.5 mm² for lengths up to 3 meters. For longer runs, use cables with at least 4 mm² cross-section to prevent sound loss.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Versatile wall mounting supports vertical or horizontal installation
  • Compatible with VESA standard brackets for flexible placement
  • Excellent integration with Ambient Sub 88 F subwoofer
  • Rotatable logo adapts to any speaker orientation
  • Clear and balanced sound with bass reflex design
VS

Disadvantages

  • Requires careful cable management to avoid short circuits
  • Customer bears full responsibility for wall mounting safety
  • Weak amplifiers may cause distortion at medium volumes
  • Sensitive tweeters require protection from high frequency signals
  • Specific mounting hardware not included with the unit
M: QW-35-FL

Product Specification

Form

Square

Principle

2-Way

Tweeter

1x 1"/25.4mm

Woofer

1x 4"/101.6mm

Frequency Range

62Hz-42kHz

Power Handling

20-80W

Impedance

4-8Ω

Sensitivity

87dB

Dimensions (WxDxH)

7.09x11.81x3.03in

Weight

6.61lbs

M: QW-35-FL

Product Description

Discover the Heco Ambient 11F Speaker

The Heco Ambient 11F stands as a premier choice for audiophiles seeking high-quality sound in a compact form. Designed specifically for wall mounting, this speaker delivers a rich and balanced audio experience suitable for both stereo music listening and immersive home cinema setups. Its sleek design allows it to blend seamlessly into any room while providing powerful performance.

When installed correctly, the Ambient 11F creates an ideal listening triangle with your seating position, ensuring that sound arrives at your ears simultaneously from both channels. This setup produces a natural and harmonious soundstage that brings your favorite tracks to life. The speaker features a two-way bass reflex configuration, which enhances low-frequency response without sacrificing clarity in the mid and high ranges.

Installation is straightforward with two versatile mounting options. You can hang the unit vertically or horizontally using the integrated metal fixtures on the back. Alternatively, the built-in threaded inserts support standard VESA mounts, offering flexibility for various interior designs. The logo on the frame is rotatable, allowing you to align it perfectly regardless of the orientation.

For optimal performance, pair the Ambient 11F with the Heco Ambient Sub 88 F subwoofer. In a home theater configuration, these speakers serve excellently as rear channels, placed behind or beside your listening area at ear level. Ensure your AV receiver crossover is set around 80 Hz for seamless integration with other speakers. Always use quality speaker cables with adequate thickness to prevent signal loss and maintain phase integrity by connecting positive terminals to positive and negative to negative.

Proper maintenance involves cleaning lacquered surfaces with mild household cleaners, avoiding furniture polish or microfiber cloths that could damage the finish. With its robust build and attention to acoustic detail, the Heco Ambient 11F remains a reliable component for enhancing your audio environment.

M: QW-35-FL

© Copyright 2026 Manual.ly