Manual.ly Logo

Goodwe HT Series 1500V Manual

0.0 · 0 Ratings

PDF manual · 57 Pages

English

M: gpt-5.6-terra
page

/ 57

Loading...
d8ad81b04abb6b96d18e2d6d176b9afd29fd page 31
User Manual V1.1-2022-07-20 09 Maintenance
45
No. Fault Cause Solutions
18
Over
Temperature
1. The inverter is
installed in a
place with poor
ventilation.
2. The ambient
temperature
exceeds 60℃.
3. A fault occurs in
the internal fan
of the inverter.
1. Check the ventilation and the ambient
temperature at the installation point.
2. If the ventilation is poor or the ambient
temperature is too high, improve the
ventilation and heat dissipation.
3. Contact the dealer or after-sales service if both
the ventilation and the ambient temperature
are normal.
19 InFan Fail
1. The fan power
supply is
abnormal.
2. Mechanical
exception.
3. The fan is aging
and damaged.
Disconnect the AC output switch and DC input
switch, then connect them 5 minutes later.
Contact the dealer or the after-sales service if the
problem persists.
20 DC Bus High
1. The PV voltage is
too high.
2. The sampling
of the inverter
BUS voltage is
abnormal.
Disconnect the AC output switch and DC input
switch, then connect them 5 minutes later.
Contact the dealer or the after-sales service if the
problem persists.
21 Gnd I Fail
The input insulation
impedance to the
ground decreases
when the inverter is
operating.
1. Check whether the working environment
of the inverter meets the requirements. For
example, the fault may occur due to high
humidity on rainy days
2. Make sure that the components are properly
grounded and the AC side is properly
grounded.
22 Utility Loss
1. Utility grid power
fails.
2. The AC cable is
disconnected, or
the AC breaker is
o.
1. The alarm is automatically cleared after the
grid power supply is restored.
2. Check whether the AC cable is connected and
the AC breaker is on.
23 AC HCT Fail
The sampling
of the AC HCT is
abnormal.
Disconnect the AC output switch and DC input
switch, then connect them 5 minutes later.
Contact the dealer or the after-sales service if the
problem persists.

Chat with your Goodwe HT Series 1500V manual using AI

Get instant AI answers from your Goodwe HT Series 1500V manual

Ask anything about the Goodwe HT Series 1500V. Answers come from this manual, with the pages they are based on.

HT Series 1500V Maintenance Schedule

Remind me when maintenance is due
Every 6-12 months
Inspect cooling and airflow paths

Check heat sinks, air intake ducts, and air outlets for foreign objects or dust. Shut down the inverter before maintenance.

Show in the manual (page 49)
Every 6-12 months
Inspect electrical connections and cables

Check cable connections are secure and inspect cables for breaks or exposed copper cores. Shut down the inverter before maintenance.

Show in the manual (page 49)
Yearly
Inspect the fans

Check that fans operate correctly, run quietly, and have no visible damage. Shut down the inverter before maintenance.

Show in the manual (page 49)
Yearly
Test the DC switches

Switch each DC switch on and off ten consecutive times and verify correct operation. Shut down the inverter before maintenance.

Show in the manual (page 49)
Yearly
Inspect seals and cable entries

Check all terminals and ports are properly sealed. Reseal a cable entry if it is not tight or is oversized.

Show in the manual (page 49)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: gpt-5.6-terra

Ask a Question

0/1000

Do you recommend HT Series 1500V?

Yes No

Frequently Asked Questions

A

The range includes 225 kW and 250 kW three-phase grid-tied string inverter models: GW225K-HT, GW250K-HT, GW225KN-HT, and GW250KN-HT.

Is this answer helpful?

A

All listed models support a maximum DC input voltage of 1500 V. Their MPPT operating range is 500 V to 1500 V, with a 550 V start voltage.

Is this answer helpful?

A

HT models provide 12 MPPT trackers with two strings per tracker. HTN models provide six MPPT trackers with three strings per tracker, offering different array design approaches.

Is this answer helpful?

A

Yes. The series supports Bluetooth with the SolarGo app, SEMS Portal monitoring, and RS485 or PLC communications. Modbus RTU is available for integration with compatible monitoring systems.

Is this answer helpful?

A

The enclosure is rated IP66. The units use intelligent fan cooling, operate from -30 C to 60 C, tolerate 0% to 100% relative humidity, and can be installed up to 5,000 m altitude with derating above 4,000 m.

Is this answer helpful?

A

Integrated protections include PV string current monitoring, insulation resistance detection, residual current monitoring, anti-islanding protection, AC overcurrent and short-circuit protection, and Type II DC and AC surge protection.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • High-output options of 225 kW and 250 kW suit large commercial and utility-scale PV plants.
  • 1500 V DC design, up to 400 kW input power, and 99.0% maximum efficiency support efficient energy conversion.
  • Flexible MPPT layouts: HT models have 12 trackers, while HTN models have six trackers with three strings each.
  • IP66 protection, intelligent fan cooling, and operation from -30 C to 60 C support demanding outdoor sites.
  • RS485, PLC, Modbus RTU, SolarGo, and SEMS Portal enable monitoring and system integration.
VS

Disadvantages

  • At 111 kg, the inverter requires careful handling, sufficient personnel, or appropriate lifting equipment during installation.
  • The system is intended for qualified electrical professionals and requires strict high-voltage safety procedures.
  • Fan cooling can create sound emissions below 70 dB, which should be considered near noise-sensitive locations.
  • Performance derating is required above 4,000 m altitude.
  • Optional functions such as LCD, remote shutdown, emergency shutdown, and anti-PID may not be included in every configuration.
M: gpt-5.6-terra

Product Specification

Note

Prices partially include 0% VAT rates for Austria and Germany

Type

Transformerless solar inverter with fan

Input voltage

500-1,500 V DC

MPP voltage range

500-1,500 V DC

Maximum PV generator output

400 kWp

Output phases

3-phase

Input

MC4

Output

Terminals

Interfaces

Bluetooth, 1x RJ-45, 1x RS-485, Modbus RTU

Noise level

<70 dB

Protection rating

IP66

Ambient temperature

-22 to +140 F

Dimensions

42.95 x 26.69 x 13.43 in (W x H x D)

Weight

244.71 lb

M: gpt-5.6-terra

Product Description

Goodwe HT 1500V Series - Read, Download & Print Free

The Goodwe HT 1500V Series is a high-capacity, three-phase string inverter range designed for utility-scale and large commercial solar installations. Available in 225 kW and 250 kW ratings, these inverters convert photovoltaic DC power into grid-compatible AC electricity for dependable energy delivery. Their 1500 V architecture supports modern high-voltage PV arrays, helping project owners reduce balance-of-system costs while maintaining a flexible system layout.

Built for demanding solar projects

The series includes the GW225K-HT, GW250K-HT, GW225KN-HT, and GW250KN-HT models. Standard HT versions offer 12 MPPT trackers with two strings per tracker, while HTN versions provide six MPPT trackers with three strings per tracker. This range gives designers practical options for adapting to array orientation, shading conditions, and site-specific string layouts.

With a maximum DC input power of 400 kW, a 500 V to 1500 V MPPT operating range, and a rated AC output voltage of 800 V, the Goodwe HT 1500V Series is tailored for high-output PV systems. Peak efficiency reaches 99.0%, while European and CEC efficiency figures remain high across the range. These characteristics support strong energy conversion performance throughout daily operation.

Monitoring, protection, and control

Integrated safety functions include PV string current monitoring, insulation resistance detection, residual current monitoring, anti-islanding protection, AC overcurrent protection, and Type II surge protection on both DC and AC sides. Optional remote shutdown, emergency shutdown, anti-PID, and PID recovery functions enable configurations aligned with applicable project and regional requirements.

Operators can use LED indicators, an optional LCD, Bluetooth connectivity, the SolarGo app, and the SEMS Portal to view operating information, configure parameters, review alarms, and monitor system status. RS485 or PLC communication and Modbus RTU compatibility support integration with wider plant monitoring infrastructure.

Designed for outdoor reliability

An IP66 enclosure, intelligent fan cooling, and an operating temperature range from -30 C to 60 C help the series serve demanding outdoor environments. The inverter is rated for operation at altitudes up to 5,000 m, with derating above 4,000 m. Its compact high-power format measures 1091 x 678 x 341 mm and weighs 111 kg.

Note: Installation, commissioning, electrical connections, and maintenance should be performed by qualified professionals using applicable local regulations, protective equipment, and approved connection methods.

Note: Correct PV polarity, secure grounding, ventilation, and appropriately rated AC protection are essential for safe, reliable operation.

M: gpt-5.6-terra

© Copyright 2026 Manual.ly