Manual.ly Logo

Gardigo Marten Shock Mobile Manual

0.0 · 0 Ratings

PDF manual · 32 Pages

English

M: OA-GPT-54-NAN
page

/ 32

Loading...
d8a566f13e982f8a49be87685dbf566d2f04 page 5
5
Das Gerät wird mit Blechschrauben oder Kabelbindern im Motorraum an der Karosserie
befestigt. Es sollte an einer Stelle des Motorraumes eingebaut werden, die vor Spritz
-
wasser und allgemeiner Verschmutzung geschützt ist. Die Hochspannungsplättchen
werden an den Stellen verlegt, an denen der Marder am wahrscheinlichsten vorbei
-
kommt. Das Gerät besitzt einen Vibrationssensor der das Gerät bei Fahrzeugstillstand
nach ca. 60 Sekunden automatisch einschaltet bzw. bei durch den Motor erzeugten
Vibrationen oder während des Fahrbetriebs ausschaltet (Abschaltautomatik). Die Mon
-
tage sollte durch autorisiertes Fachpersonal erfolgen.
Es ist unbedingt darauf zu achten, dass die Metallflächen der Plättchen weder stark
verschmutzt sind noch ständiger Nässe ausgesetzt werden können. Dies könnte
Kriechströme erzeugen, die zu einem Kurzschluss und damit zum Ausfall der Hoch
-
spannung führen können. Gegenüber normaler Luftfeuchtigkeit bestehen keine An-
wendungsbedenken.
Nach der Montage wird das Gerät mittels Schalter eingeschaltet. Beim Einschalten
leuchtet das weiße Licht und grüne LED auf und erlischt danach. Die Grüne LED leuch
-
tet permanent während die Platten unter Hochspannung stehen und bei Frequenz-
Aussendung.
Bei Spannungsabfall der Batterie ca. < 3,2 Volt wird alle 60 Sekunden die grüne LED 3x
kurz mit einem Signalton aktiviert. Das Gerät muss mit dem Schalter ausgeschaltet
werden und nach ca. 60 Sekunden (Abbau der Hochspannung) kann es von der Trä
-
gerplatte genommen werden. Die Bodenplatte wird mittels der 6 Schrauben vorsichtig
geöffnet und die Batterien können dann gewechselt werden. Wir empfehlen nur neue
hochwertige Alkaline Batterien gleicher Art für eine lange Funktionsdauer zu verwen
-
den. Es empfiehlt sich vor Einbau auf die Montageplatte, die Kontaktflächen zu reini-
gen. Der Haltegummi für das Gerät sollte auf jeden Fall bei Montage im Fahrzeug zur
Fixierung auf dem Geräteträger angewendet werden, damit sich das Gerät auf keinen
Fall vom Geräteträger löst.
6. Allgemeine Hinweise zum Einbau
• Wurde Ihr Fahrzeug bereits von Mardern besucht, haben die Tiere höchstwahrschein
-
lich Duftmarken zur Revierkennzeichnung hinterlassen. Diese Gerüche müssen vor
der Montage unbedingt entfernt werden. Am besten geschieht dies durch eine
gründliche Motorwäsche.

Chat with your Gardigo Marten Shock Mobile manual using AI

Get instant AI answers from your Gardigo Marten Shock Mobile manual

Ask anything about the Gardigo Marten Shock Mobile. Answers come from this manual, with the pages they are based on.

Marten Shock Mobile Maintenance Schedule

Every 60 seconds
Check battery voltage indicator

If the green LED flashes 3 times every 60 seconds with a tone, replace batteries as voltage drops below 3.2 volts.

Before installation
Clean contact surfaces

Clean contact areas on the mounting plate before installing the device to ensure proper function.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend Marten Shock Mobile?

Yes No

Frequently Asked Questions

A

It combines ultrasonic sound in the 12-23 kHz range, changing frequency intervals, high-voltage contact plates charged to about 300 V, and a 4-times LED flash. The goal is to make the engine compartment unpleasant so intruders move away.

Is this answer helpful?

A

The device emits ultrasound in cycles: it turns sound on for about 5 seconds and then turns it off for about 30 seconds. The exact pattern is designed to reduce habituation by also changing the frequencies.

Is this answer helpful?

A

The manual describes the shock as painful but not lethal. Still, the device operates with high voltage, so strict safety handling is required, including proper separation of plus and minus plates and waiting for the high voltage to dissipate before any service.

Is this answer helpful?

A

A vibration sensor controls activation. It automatically switches on after the vehicle has been parked for about 60 seconds, and it switches off when the vehicle is running or when motor vibrations are detected during driving.

Is this answer helpful?

A

It runs on batteries: 4 x 1.5 V AAA. When battery voltage drops below about 3.2 V, the unit indicates the low state by activating the green LED briefly 3 times every 60 seconds along with a signal tone, and you should replace the batteries.

Is this answer helpful?

A

Ensure the plate metal surfaces are not heavily soiled and not exposed to constant wetness. Prevent direct shorting between high-voltage plus and minus modules or contact with the chassis. Mount the yellow warning sticker visibly in the engine compartment, and ensure the LED flash is not covered.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Varying ultrasonic frequencies (12-23 kHz) help prevent animals from adapting to a constant sound.
  • High-voltage contact plates (about 300 V) provide an additional deterrent when animals step on them.
  • 4-times LED flash triggers at high-voltage activation to increase the scare effect.
  • Automatic activation with a vibration sensor supports use when the vehicle is parked.
  • Clear electrical specifications and operating intervals are provided for predictable behavior.
VS

Disadvantages

  • Installation requires careful routing of high-voltage modules and is recommended for qualified professionals.
  • Direct contact shorting between plus and minus plates or with vehicle chassis can destroy the device.
  • Deterrent performance depends on local sound dispersion and animal behavior, which can vary.
M: OA-GPT-54-NAN

Product Specification

Type

High-voltage device, Ultrasound device

Sound pressure

65dB

Frequency range

12kHz-23kHz

Features

Battery operation, LED flashes

Dimensions

3.35x4.13x1.57in

M: GO-GEM-FL-25

Product Description

Gardigo Marten Shock Mobile Manual: Mobile deterrence for the engine compartment

Designed to keep martens and mice away

The Gardigo Marten Shock Mobile is a mobile protection device made to deter martens and mice from the inside of the vehicle and, especially, the engine compartment. Instead of relying on a single tone, it emits varying ultrasonic frequencies that help prevent animals from getting used to the sound. Over time, the unpleasant experience encourages them to move to another area.

How it works: sound, high-voltage contact, and LED flashes

During operation, the unit produces ultrasonic signals in the 12-23 kHz range in intervals, with sound on for about 5 seconds and off for about 30 seconds. The changing frequencies are intended to maintain the deterrent effect.

The device also includes special high-voltage contact plates. Internally, a capacitor charges these plates to about 300 V. If an animal steps onto the outer contact plates, it receives an unpleasant electric shock that is described as painful but not lethal. At the same time, a 4-times LED flash is triggered to add a visible scare effect.

Installation and activation behavior

For best results, the unit should be mounted on the vehicle body inside the engine bay, in a location protected from splash water and heavy dirt. The contact plates should be routed so they are likely to be touched by an intruding animal. The device uses a vibration sensor to switch on automatically when the vehicle is parked for about 60 seconds, and it switches off during vehicle operation.

Power is battery-based (4 x 1.5 V AAA). The unit provides status indications with LEDs and a signal tone when battery voltage drops below about 3.2 V. For safety, high-voltage parts must never be shorted, and the device should be serviced only after the high voltage has safely dissipated.

Notes

  • Animal reactions can vary by species and individual behavior.
  • Installation is intended for qualified professionals.
  • Do not cover the LED flash, and do not expose the metal plate surfaces to constant wetness or heavy contamination.

Key results

  • Varying ultrasonic frequencies (12-23 kHz) help reduce habituation.
  • High-voltage contact plates (about 300 V) provide a painful but non-lethal shock.
  • 4-times LED flashes add an extra deterrent effect.
  • Vibration-triggered operation activates after parking and deactivates during driving.
  • Battery monitoring warns you when voltage drops below about 3.2 V.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly