Manual.ly Logo

Ergotec PM-705N Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: QW-35-FL
page

/ 2

Loading...
06ad1698421329e9c938a74e7e1f0f0f9358 page 2
Thank you for deciding to buy your new seat post from our company.
Compare the level number on the seat post with the adjacent table
in order to check whether it is suitable for the intended use.
Before fitting the seat post please make sure that it is suitable
for the maximum approved weight of the bike. You will find the
relevant information on the product description or obtain it from
your bicycle dealer.
Before use please read the following assembly and safety
instructions carefully. Keep them in a safe place and pass
them on to the next owner if necessary.
Assembly
Basic technical knowledge is required for the assembly of this product. If you do
not have this knowledge, please use the services of a specialist bicycle dealer.
Before assembly please check that the outer diameter of the seat post
(27.2 or 31.6 mm) matches the inner diameter of the seat tube of the frame.
If the clamping area of the seat tube of the frame is larger, you can adjust the
diameter with a suitable seat post adapter (min. length 80 mm). For safety
reasons we recommend the use of original ergotec seat post adapters. These
are available from specialist bicycle dealers.
The end of the seat tube must be free from burrs, otherwise
there is a risk of breaking!
Before the seat post is inserted the clamping area of the seat tube should
always be treated with water-resistant grease, because otherwise corrosion
could make subsequent modification of the seating height difficult.
You now insert the seat post into the seat tube of the frame.
For safety reasons the seat post must be inserted into the seat
tube to the depth which is marked (80 mm), unless the bicycle
manufacturer has specified greater insertion depth. Please refer
to the user information provided by the bicycle manufacturer.
In order to fix the seat post in the frame you tighten the clamping screw of the
seat post or the quick-clamping mechanism to the level of tightness specified
by the bicycle manufacturer.
Before mounting the saddle please check the compatibility of the seat post and
the saddle.
Press protector
c
out of the parallelogram joint.
Now place the frame of the saddle into the two guide grooves of the saddle
clamp.
Next you adapt the position of the saddle to your individual requirements.
Now you tighten the saddle clamping screw
d
with a 5 mm hexagonal key
to a torque of 8 Nm.
After that you replace protector
c
in the parallelogram joint.
For safety reasons the max. torque of 8 Nm
should not be exceeded.
Setting
You can adapt the suspension individually to your body weight, cycling style and
road surface.
For this purpose you sit on the saddle. With the correct setting the seat post
should approx. bottom out at 20 % of the suspension travel (approx. 5 mm).
In order to increase the hardness of the suspension you first remove locking
nut
e
at the base of the seat post by turning it in an anti-clockwise direction
with a 6 mm hexagonal key.
You can now turn adjusting nut
f
with a 10 mm hexagonal key in a clockwise
direction for a harder setting and anti-clockwise for a softer setting.
After that you replace the locking nut and tighten it until it is handtight.
If the standard settings are not suitable for you can obtain steel springs from a
specialist bicycle dealer. We offer these in 4 different levels of hardness:
up to 70 kg / Art.Nr. 06036000, 70 - 90 kg / Art.Nr. 06036100,
90 - 110 kg / Art.Nr. 06036200, 110 - 130 kg / Art.Nr. 06036300
To exchange the steel spring you first release the seat post clamp or the
quick-clamping mechanism.
You now withdraw the seat post from the seat tube of the frame.
Next you remove snap ring
g
with a snap ring spanner.
Assembly and safety instructions for
Suspension seat post PM-705N
Mountain-Bike/Race-Bike Safety Level
max. 100 kg max. 100 kg
max. 120 kg max. 120 kg
E-BIKE
25 km/h + 45 km/h
max. 100 kg max. 100 kg
max. 120 kg max. 120 kg
Trekking-Bike Safety Level
max. 100 kg max. 100 kg
max. 120 kg max. 120 kg
max. 140 kg max. 140 kg
max. 160 kg max. 160 kg
E-BIKE
25 km/h max. 140 kg max. 100 kg
E-BIKE
25 km/h max. 160 kg max. 140 kg
E-BIKE
45 km/h* max. 140 kg max. 140 kg
E-BIKE
45 km/h* max. 160 kg max. 140 kg
City-Bike Safety Level
max. 100 kg max. 100 kg
max. 120 kg max. 120 kg
max. 140 kg max. 140 kg
max. 160 kg max. 160 kg
max. 180 kg max. 180 kg
E-BIKE
25 km/h max. 140 kg max. 100 kg
E-BIKE
25 km/h max. 160 kg max. 140 kg
E-BIKE
25 km/h max. 180 kg max. 160 kg
E-BIKE
45 km/h* max. 140 kg max. 140 kg
E-BIKE
45 km/h* max. 160 kg max. 140 kg
Jugend/Young adult Safety Level
max. 100 kg max. 100 kg
Kinderrad/Youth-Bike Safety Level
12"-24"
Lenksystem
Steering system
Sattelstütze
Seatpost
The product classification of the ergotec Safety Level corresponds
to the DIN EN ISO 4210 norm for bikes and DIN EN 15194 for e-bikes.
E-bike-type: pedal assist up to the indicated speed.
* Retrofitting only with the approval of a recognised certifying
body and entry in the documents for the bike.
english
Valid: 06.04.2017
Guarantee
For ergotec seat posts the following guarantee periods apply:
with safety level 6 6 years or 35,000 km
with safety level 5 5 years or 30,000 km
with safety level 4 4 years or 25,000 km
with safety level 3 3 years or 20,000 km
with safety level 2 3 years or 15,000 km
Guarantee claims should be processed
through a specialist bicycle dealer.
Safety instructions
The tightness of the bolts must be checked after approx. 500 km and once more
during the regular service intervals (with once a year as a minimum).
The seat post is not suitable for competitions. The high level of strain
could lead to damage to the seat post.
No additional weights such as child seats, luggage racks or trailers
should be attached to the seat post. Excessive loading can cause the
seat post to break.
To prevent the risk of a fall or accident the seat post must always
be replaced if it has been damaged.
CYCLINGRIGHT.COM
k
i
h
f
g
e
Direction of driving
c
j
d
Direction of driving
Remove locking nut
e
by turning it clockwise with a 6 mm hexagonal key.
Now remove adjusting nut
f
from the seat post by turning it ant-clockwise
with a 10 mm hexagonal key.
You can now remove centering sleeve
h
, steel spring
i
and sleeve
k
.
For assembly you implement the above steps in reverse.
Maintenance
In order to ensure high performance, safety and a long product life, regular
maintenance is required after approx. 200 operating hours or at least once a year.
Greasing the bearings
For this purpose you remove protector
c
from the parallelogram joint.
Now carefully clean the entire area of the 4 bearings
j
with a biodegradable
cleaning agent.
Then you grease the entire area of bearings
j
with an acid-free grease,
which can be obtained from a specialist bicycle dealer.
After that you replace protector
c
in the parallelogram joint.
You should always use acid-free grease, because otherwise
the bearings could be chemically altered or destroyed.

Chat with your Ergotec PM-705N manual using AI

Get instant AI answers from your Ergotec PM-705N manual

Ask anything about the Ergotec PM-705N. Answers come from this manual, with the pages they are based on.

PM-705N Maintenance Schedule

Remind me when maintenance is due
Yearly
Check bolt tightness

Check the tightness of the bolts regularly during service intervals, at least once a year.

Yearly
Grease parallelogram bearings

Clean the four bearings with biodegradable agent and grease with acid-free grease to prevent damage.

Every 500 km
Check bolt tightness

Check the tightness of the bolts after approximately 500 km to ensure safety.

Every 200 hours
Perform regular maintenance

Regular maintenance is required after approx. 200 operating hours or at least once a year for performance and safety.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend PM-705N?

Yes No

Frequently Asked Questions

A

Yes, it fits mountain, trekking, and city bikes with specific safety levels rated for various max weights up to 180 kg.

Is this answer helpful?

A

Turn the adjusting nut clockwise for harder settings and anti-clockwise for softer ones, ensuring proper preload for your weight.

Is this answer helpful?

A

Warranty ranges from three to six years or 15,000 to 35,000 km depending on the specific safety level of the unit.

Is this answer helpful?

A

No, additional weights like child seats or trailers must not be attached as this causes excessive loading and breakage risk.

Is this answer helpful?

A

Clean and grease bearings after 200 operating hours or at least once a year to ensure safety and longevity.

Is this answer helpful?

A

You must insert the post at least 80 mm into the seat tube unless the bike manufacturer specifies a greater depth.

Is this answer helpful?

A

Yes, you will need 6 mm and 10 mm hex keys for the suspension adjustment and 5 mm for the saddle clamp.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Adjustable suspension preload allows tuning to body weight and riding style
  • Compatible with acid-free grease for longevity and component protection
  • Warranty coverage extends up to six years depending on safety level
  • Replaceable steel springs offer customization for different weight ranges
  • Clear torque specifications ensure correct assembly without damage
VS

Disadvantages

  • Requires basic technical knowledge for proper installation and adjustment
  • Not suitable for competitive racing due to high strain risks
  • Maintenance schedule requires cleaning and greasing at regular intervals
  • Cannot attach child seats or cargo racks directly to the post
  • Limited to specific seat tube diameters of 27.2mm or 31.6mm
M: QW-35-FL

Product Specification

Type

Suspension seatpost

Colors

Black

Material

Aluminum 7075

Length

13.78 in

Diameter

1.24 in

Travel

1.06 in

Weight

1.35 lb

M: QW-35-FL

Product Description

Enhance Your Ride with Superior Comfort

Riding smooth trails requires equipment that adapts to the terrain. The Ergotec PM-705N 31.6mm Suspension Seat Post offers a solution for cyclists seeking reduced fatigue and improved traction on rough surfaces. When you consult the Ergotec PM-705N 31.6mm Suspension Seat Post Manual, you discover a device designed for versatility across mountain, trekking, and city bikes. It stands out in performance testing.

Installation and Safety

Proper installation is critical for safety. The post fits into seat tubes of 31.6mm diameter, though 27.2mm models exist using adapters. Always ensure the frame tube end is free of burrs to prevent breakage. Apply water-resistant grease to the clamping area to avoid future corrosion. The minimum insertion depth must reach the 80 mm mark to secure the structure effectively.

Adjusting the Suspension

One standout feature is the adjustable coil spring. Riders can tune the preload based on their body weight and riding style. By turning the adjusting nut, the suspension becomes either softer or stiffer. The recommended starting point is a rebound of roughly 20 percent of the total travel, approximately 5 mm when a rider sits on the saddle.

Maintenance Guidelines

Longevity depends on regular care. Cleaning and lubricating the bearings every 200 operating hours or annually keeps the mechanism functioning smoothly. Use only acid-free grease to protect the internal components from chemical damage. Always check bolt tightness every 500 km to ensure secure performance.

Important Notes

This component is not intended for competitive racing due to high strain levels. Avoid attaching cargo racks or child seats directly to the post. Warranty coverage varies from three to six years depending on the safety level designated on the unit. Replace the unit immediately if any damage is detected to prevent accidents. It is crucial to inspect the unit visually before every ride for cracks.

The system supports various maximum weight limits defined by safety levels. Some levels accommodate up to 180 kg for city bikes. Different steel springs are available for specific weight ranges between 70 and 130 kg. This customization ensures optimal performance for individual riders. Always follow torque settings specified by the manufacturer. The saddle clamp requires 8 Nm tightness. Exceeding this limit may damage the saddle rails or the post head. Professional installation is recommended if technical knowledge is lacking. Maintenance ensures reliability over time. Ensure all bolts are tightened correctly to prevent slipping during operation. This protects the rider from potential falls. Regular checks help maintain safety standards throughout the lifespan.

M: QW-35-FL

© Copyright 2026 Manual.ly