Manual.ly Logo

Einhell GC-EM 1536 Manual

0.0 · 0 Ratings

PDF manual · 124 Pages

English

M: OA-GPT-54-NAN
page

/ 124

Loading...
0b8a14b461335fe36794507459cfa61bc53b page 18
GB
- 24 -
Fitting the wheels (Fig. 3a and b)
Take a rear wheel (Fig. 2/Item 11) and push it
onto the axle as shown in Fig. 3a. Then slide a
washer (Fig. 2/Item 15) onto the axle and fasten
all parts with the supplied split pin (Fig. 2/Item 14)
as shown in Fig. 3a. Finally, press the wheel cap
(Fig. 2/Item 12) onto the wheel as shown in Fig.
3b. Proceed in exactly the same way on the other
side.
Mounting the push bar (Fig. 4 to 7).
Mount a bottom push bar (Fig. 2/Item 2) onto the
screw provided for it and secure everything with
a wing nut (Fig. 2/Item 13) as shown in Fig. 4.
Proceed in the same way on the other side. When
you fi t the top push bar you can decide the height
of the push bar by selecting the appropriate fas-
tening hole (Fig. 5). Finally, secure the top push
bar to the bottom push bar as shown in Fig. 6.
Now you can attach the motor cable to the push
bar (Fig. 7/Item A) using the cable clips (Fig. 2/
Item 16).
Mounting the grass basket
(see Figs. 8a and b)
Press the grass box handle (Fig. 8a/Item 21)
into the grass basket as shown in Fig. 8a. Before
you fi t the grass basket you must ensure that the
motor is switched off and the blade is not rotating.
Lift the ejector fl ap (Fig. 8b/Item 3) with one hand.
With the other hand, hold the grass basket by the
handle and hook it in from above (Fig. 8b).
Filling level indicator of the grass collector
The grass collector is equipped with a fi lling level
indicator (Fig. 2/Item 18) which is opened by the
airfl ow that the lawn mower generates during ope-
ration. If the fl ap closes during mowing, the grass
collecting device is full and must be emptied. To
ensure the proper functioning of the fi lling level
indicator, the holes under the fl ap must always be
kept clean and passable.
Adjusting the cutting height
Important!
Adjust the cutting height only when the motor is
switched off and the power cable has been dis-
connected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
power plug.
The cutting height is adjusted as follows
(see Fig. 9):
1. Push the lever inwards.
2. Set the lever to the desired cutting height.
3. Release the lever and check that it is securely
seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-66 mm
in 5 intervals, and can be read off on the scale.
Power supply
The lawn mower can be connected to any light
socket-outlet with a 220-240 Volt alternating
current. However, the socket outlet must have an
earthing contact protected by a 16 A circuit brea-
ker. Additionally, a residual current device (RCD)
circuit-breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not dama-
ged. The total length of the power cable should
not exceed 50 meters; going beyond this distance
will reduce the power output of the electric motor.
The power cable must have a cross-section of 3
x 1.5 mm. The insulating sheath of lawn aerator
power cables is frequently damaged.
Some of the causes for this are:
•
Cuts caused by driving over the cable.
•
Pinching when the power cable is dragged
under doors and pulled through windows.
•
Cracking due to old age of the insulation.
•
Kinking by improperly fastening or guiding the
power cable.
The power cables must, at the very minimum, be
of type HO5RN-F and 3-stranded. The cable type
must be printed somewhere on the power cable.
Only purchase power cables that are marked!
Plugs and socket couplers for the power cables
must be made from rubber and splash-proof.
There is a limit to how long power cables can be.
Longer power cables require larger conductor
cross-sections. Power cables and connecting li-
nes must be regularly checked for damage. Ensu-
re that the lines are switched off before checking
them. Completely unwind the power cable. Also
check power cable entry points, plugs and socket
couplers for kinks.
Anl_GC_EM_1536_SPK7.indb 24Anl_GC_EM_1536_SPK7.indb 24 15.07.14 12:5815.07.14 12:58

Chat with your Einhell GC-EM 1536 manual using AI

Get instant AI answers from your Einhell GC-EM 1536 manual

Ask anything about the Einhell GC-EM 1536. Answers come from this manual, with the pages they are based on.

GC-EM 1536 Maintenance Schedule

After each use
Clean the grass basket and net

Clean the inside of the grass basket and especially the net after every use to ensure proper grass collection.

Show in the manual (page 26)
After each use
Clean the mower housing underside

Keep the underside of the mower housing clean and remove grass build-up to prevent starting issues and poor cutting quality.

Show in the manual (page 25)
Regularly
Check blade condition and sharpness

Regularly check if the blade is securely attached, in good condition, and sharp. Sharpen or replace if worn.

Show in the manual (page 26)
Regularly
Inspect power cable for damage

Power cables and connecting lines must be regularly checked for damage while switched off.

Show in the manual (page 24)
Regularly
Check fasteners tightness

Ensure all mounting components like screws, bolts, and nuts are always tightened for safe operation.

Show in the manual (page 26)
Regularly
Lubricate wheels and axles

Clean and lubricate all screwed parts, wheels, and axles to ensure long equipment life.

Show in the manual (page 26)
Regularly
Check grass catch assembly wear

Frequently check the grass catch assembly for signs of wear and replace worn or damaged parts immediately.

Show in the manual (page 26)
At season end
Perform general inspection

At the end of the season, perform a general inspection and remove all accumulated grass and dirt.

Show in the manual (page 27)
At season start
Check blade before first use

Before the start of each season, definitely check the condition of the blade.

Show in the manual (page 27)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend GC-EM 1536?

Yes No

Product Specification

Type

Lawn mower

Power

1500W

Working width

14.17 in

Working height

0.98-2.56 in, height adjustable (central), 5 levels

Recommended lawn area

up to 6,458.35 sq ft

Collection volume

10.04 gal

Special features

Rear discharge, Fill level indicator

Weight

22.05 lb

Scope of delivery

Grass collection box

M: OA-GPT-54-NAN

Product Description

M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly