Manual.ly Logo

Eden WaterParadise 425-25 Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: QW-35-FL
page

/ 2

Loading...
c9dffd84210196a86f6298fbdfba99927a7e page 1
bessere Stelle im Aquarium oder arrangieren Sie die Pflanzen etwas anders,
falls der Wasserfluss gehindert ist. Prüfen Sie die Temperatur nach einiger Zeit
dann nochmals mit dem Thermometer.
b Sollten die Temperaturwerte immer noch sehr unterschiedlich sein, kann man
den Regelheizer neu justieren.
c Entfernen Sie dazu das mitgelieferte Werkzeug auf der Halterung oder verwen-
den Sie einen Schraubenzieher (Fig. 5).
d Halten Sie den blauen Drehregler auf dem eingestellten Wert, und drehen Sie
den orangenen Regler des Kalibriersystem gegen + oder gegen -, je nachdem,
ob die gemessene Temperatur niedriger oder höher ist, als die auf der Skala
eingestellte (Fig. 6). Es gibt 3 fixierte Positionen gegen + und -. Jede Position
entspricht etwa 1° C. Wenn Sie zum Beispiel den Regler auf 24°C eingestellt
haben aber 22°C gemessen haben, drehen Sie den orangenen Regler 2
Positionen Richtung +. Insgesamt ist eine Nachkalibrierung in einem Bereich
von 6°C möglich: 3°C ins + und 3°C ins -.
– VERSUCHEN SIE NIE, DIESE WERTE ÜBERSCHREITEN !
5- Drehen Sie den blauen Regler, oder den orangenen Regler des Kalibriersystems
nie über Arretierung hinaus ! dadurch kann der Thermostat beschädigt werden.
Eine falsche Anwendung des Produktes wird von der Garantie nicht gedeckt.
6- Das Licht zeigt an, dass der Regelheizer in Funktion ist. Wenn die eingestellte
Temperatur erreicht wird, schaltet das Licht aus. Der Heizer schaltet sich auto-
matisch an und aus um die eingestellte Temperatur zuhalten.
7- Prüfen Sie von Zeit zu Zeit die Temperatur des Wassers, um Ihren Fischen ideale
Bedingungen bieten zu können.
GARANTIE
Für dieses Produkt gewähren wir ab dem Verkaufsdatum eine 24 monatige
Garantie auf Material und werkseitige Montage. Das Gerät wurde nach den
IEC EN 335-2-55 Sicherheitsvorschriften konstruiert und nach sorgfältigen
Arbeitsmethoden sowie unter Verwendungen von qualitativ hochwertigen
Materialen hergestellt. Damit ist eine dauerhaft hohe Zuverlässigkeit und
Leistungsstärke garantiert. Die Garantie erstreckt sich nicht auf unsachge-
mäße Handhabung, Beschädigung aller Art und technische Veränderungen
am Gerät. Insbesondere für verschmutze Geräte wird kein Ersatz geleistet.
Die Garantie wird gewährt, wenn das Gerät in allen Teilen vollständig uns
zusammen mit der Empfangsbestätigung oder Rechnung eingereicht wird. Im
Garantiefall schicken Sie das Gerät zusammen mit dieser Urkunde und dem
Rechnungsbeleg an Ihren Händler zurück. Bei gerechtfertigem Garantieanspruch
behalten wir uns vor, das Gerät zu reparieren oder zu ersetzen. Ansprüche und
Folgenschäden, die aus unsachgemäßem Gebrauch, mangelnder Pflege oder
Missachtung der Sicherheitsvorschriften entstehen, sind von der Garantie aus-
genommen. Verschleißschäden an Verschleißteilen fallen nicht unter unseren
Garantieschutz.
SICHERHEITSVORSCHRIFTEN
♦ Vor jeglichem Wasserkontakt und Eintauchen der Hände sind alle im Wasser
befindlichen Geräte vom Netz zu trennen.
♦ Prüfen Sie vor Anschluss des Gerätes, ob die Betriebspannung (siehe
Aufdruck) mit der Netzspannung übereinstimmt.
♦ Nur zu betreiben mit installiertem Fehlerstromschutzschalter (FFI) max.
0.03A Empfindlichkeit.
♦ DEN REGELHEIZER ERST ANS NETZ ANSCHLIESSEN, NACHDEM ER IM WASSER
EINGETAUCHT IST.
♦ Der Regelheizer muss mindestens bis zur “MINDEST-TAUCHTIEFE/MINIMUM
WATER LEVEL” (fig. 1) Anzeige eingetaucht werden.
♦ Warten Sie nachdem das Gerät eingetaucht wurde einige Minuten Lang mit
dem Anschalten, damit der Thermostat sich an die Wassertemperatur
anpassen kann.
♦ Das Netzkabel dieses Gerätes kann weder repariert noch ausgetauscht
werden; bei Beschädigung muss das Gerät durch ein Neues ersetzt werden.
♦ Geräte mit dem aufgedruckten Symbol
sind ausschließlich für den
Gebrauch in Zimmer und Innenräumen geeignet.
♦ VORSICHT! Der Betrieb in Schwimmbecken oder Badewannen ist nicht
gestattet.
ACHTUNG!
Das Gerät nicht außerhalb des Wassers verwenden oder für anderen
Anwendungen als im Aquarium/Terrarium einsetzen. Vor Herausnehmen
aus dem Wasser muss das Gerät ausgeschaltet werden und sich abgekühlt
haben. Vor jeglicher Pflege/Reinigung des Aquariums ist der Regelheizer
vom Netz zu trennen.
WICHTIG
Dieser hochwertige Regelheizer ist mit einem patentierten Temperatur-
Kalibrierungssystem ausgestattet. Dieses ermöglicht eine Neujustierung für den
Fall, dass es Abweichungen zwischen der auf der Temperaturskala eingestellten
Temperatur und der durch ein Präzisionsthermometer ermittelten Temperatur gibt.
Falls erforderlich, folgen Sie den Anweisungen unter Punkt 4.
INSTALLATION
Um eine ideale Wärmeverteilung im Aquarium zu erreichen, ist der Regelheizer
in einer Zone mit gutem Wasserumlauf und dem Heizelement zum Aquarienboden
zeigend zu platzieren.
Bei Nichtbefolgen kann auch der Thermostat nicht richtig funktionieren.
Der Regelheizer kann vollständig eingetaucht werden und muss mindestens bis zur
Anzeige “MINDEST-TAUCHTIEFE“ (Fig 1) unter Wasser sein.
1. Die Saugnäpfen an der Halterung wie in Fig. 2 gezeigt befestigen.
2. Reinigen Sie die Aquarienscheibe von Algen und anderen Ablagerungen und
pressen Sie die Halterung mit den Saugnäpfen fest an die Scheibe (Fig. 3). Damit
sich der Thermostat an die Temperatur des Wassers anpassen kann, sollten Sie
ca. 30 Minuten warten, bevor Sie ihn ans Netz anschließen.
3. Drehen Sie den blauen Drehregler zur Temperatureinstellung bis zum gewünsch-
ten Wert (Fig. 4). Lassen Sie den Regelheizer etwa einen Tag im Betrieb und
prüfen Sie dann die Temperatur des Wassers durch ein Präzisionsthermometer.
4. Falls die auf der Skala eingestellte Temperaturniedriger als die durch das
Thermometer ermittelte Temperatur ist, gehen Sie wie folgt vor:
a Prüfen Sie den Wasserfluss um den Regelheizer. Wählen Sie eventuell eine
b Si on trouve encore de la différence, on peut la corriger en intervenant sur le
système de post-calibrage (orange).
c Enlever l’outillage spécial qui se trouve sur le support des ventouses (fig. 5)
ou utiliser une tourne-vis.
d Tenir le bouton de réglage principal (bleu) avec une main pour éviter à
l’échelle de se déplacer de celle-la déjà fixée sur le point de repère et tourner
le bouton de post-calibrage (orange) vers + si la valeur de la température
que vous avez mesurée est plus basse de celle-la indiquée en correspondance
du point de repère, ou vers - en cas la température mesurée est supérieure à
celle indiquée par le point de repère (fig. 6). Le bouton de post-étalonnage
peut être réglé sur 6 diverses positions, 3 vers le + et 3 vers le -. Chaque
position corresponde à peu prés à 1°C. Si on a réglé le chauffe-eau sur une
température de 24° et on mesure 22°C, il suffit de tourner le bouton de post-
étalonnage 2 positions vers +.
5- ATTENTION à ne pas dépasser les limites en tournant le bouton de réglage et/ou
le bouton de post-étalonnage car ça pourrait endommager le thermostat. Chaque
manumission rendra la garantie vide de valeur.
6- L’allumage de la lampe témoin signifie que le thermoplongeur chauffe. Lorsque
l’eau aura atteint la température sélectionnée, la lampe témoin s’éteindra. Elle se
rallumera automatiquement afin de maintenir la température au niveau désiré.
7- Il est recommandé de vérifier régulièrement la température de l‘aquarium pour
garantir aux poissons des conditions de vie idéales.
GARANTIE
Le matériel et l’assemblage de cette unité, sont garanti pendant 24 mois de la
date d’achat. L’unité a été fabriquée en conformité aux Normes de Sécurité
IEC EN 60 335-2-55 avec les technologies les plus modernes en utilisant des
matériaux de qualité pour garantir la puissance, la fiabilité et une longue satis-
faction. Cette garantie ne couvre pas les défauts dus à altération, négligence,
mauvaise utilisation, modifications techniques ou le mauvais entretien. La
garantie sera reconnue uniquement si l’unité est retournée dans son intégrité,
accompagnée par la preuve ou facture d’achat. Pour utiliser cette garantie
retourner l’unité au fournisseur avec ce bon de garantie complété et la preuve
d’achat. Nous nous réservons le droit de remplacer ou réparer les unités retour-
nées sous garantie. Cette garantie ne couvre pas les défauts causés par emploi
non convenable, par négligence ou la non-observance des normes de sécurité.
Les pièces sujettes à l’usure ne sont pas couvertes par cette garantie.
PRECAUTIONS D’EMPLOI
♦ Débrancher toutes les installations électriques avant de mettre vos mains
dans l’eau.
♦ Vérifier que la tension de votre ligne corresponde au voltage indiqué sur
l’étiquette.
♦ A’ utiliser seulement en adaptant un disjoncteur différentiel = 0.03 A
♦ NE PAS BRANCHER LE CHAUFFE-EAU A LA PRISE AVANT DE L’AVOIR IMMERGE.
♦ Le chauffage doit être immergé au minimum jusqu’au l’indication “NIVEAU
MINIUMUM DE L EAU” (fig. 1).
♦ Après l’avoir plongé, attendre quelque minute avant de brancher le chauf-
fage afin de permettre au thermostat de s’adapter à la température de
l’eau.
♦ Avant de le retirer de l’eau ou en occasion de changement ou rajout d’eau, il
est recommandé de le débrancher et lui permettre de refroidir.
♦ Le câble de cet appareil ne peut pas être réparé ou remplacé.
En cas de dommage il faut remplacer l’unité complète.
♦ Si l’unité est munie du symbole
celle-ci doit être utilisée uniquement à
l’intérieur.
♦ Avertissement: ne pas utiliser dans piscines ou salles de bain.
MISE EN GARDE:
Ce chauffe-eau ne doit jamais fonctionner hors de l’eau ou pour des
utilisations diverses. Avant de le retirer de l’eau, débrancher et attendre
afin qu’il refroidisse. Débrancher l’appareil avant de mettre vos mains
dans l’eau.
IMPORTANT:
Ce chauffe-eau de haute de gamme est équipé d’un système de post-calibrage bre-
veté qui vous permette de le re-talonner en cas de différences entre la température
sur l’échelle et celle éventuellement trouvée par un thermomètre de précision.
Si nécessaire suivre les indications au point 4 des instructions suivantes.
INSTALLATION
Installez le chauffe-eau de façon à permettre une libre circulation de l‘eau autour
du tube de verre afin d’obtenir une répartition uniforme de température autrement
le thermostat ne peut pas fonctionner correctement.
Le chauffe-eau est complètement submersible et pour fonctionner correctement il doit
être immergé au moins jusqu‘au repère “NIVEAU MINIMUM DE L’EAU” (fig. 1).
1- Montez les ventouses sur le support en les insérant comme en fig. 2.
2- Enlever les algues de l‘endroit choisi et y fixer le chauffe-eau. Presser fermement
les ventouses contre le verre pour les faire adhérer à la paroi de l’aquarium (fig.
3). Attendre 30 minutes avant de brancher la prise pour permettre au chauffe-
eau de s’acclimater à la température de l’aquarium.
3- Tourner le bouton de réglage jusqu’à ce que la valeur choisie soit en face du
point de repère (fig. 4). Laisser fonctionner pendent 24 heures. Prendre la
température avec un thermomètre de précision.
4- Si la température prise par le thermomètre et celle la du point de repère résultent
très différentes, corriger l’étalonnage grâce au bouton de réglage en:
a Vérifier la libre circulation de l’eau autour du tube et éventuellement changer
la position ou déplacer les plantes ou autres choses qui pourraient déranger
la circulation et laisser le chauffage travailler pendant quelque heure avant
de re-vérifier la température.
make sure the heating part of the unit is at the very bottom of the aquarium.
b. Should you still find a difference you can correct the set value by adjusting the
calibration control knob (orange).
c. Remove the special device inserted in the suction cup support, just pulling it
out of its location (fig. 5) or use a flat blade screwdriver.
d. Hold the control knob (blue) with one hand so that the scale indicator does
not move from the value of temperature you want to have and rotate the post-
calibration knob (orange) toward + if the value of temperature you measured
is lower than the one on the scale, or toward - in case the temperature you
measured exceeds the one you have set (fig. 6). There are 6 preset positions,
3 toward + and 3 toward -. Each position corresponds to about 1°C. So i.e. if
you have set a temperature of 24°C and you measure 22°C just turn the post
calibration knob 2 steps toward +.
5- NEVER ATTEMPT to exceed the limits of both the temperature control knob and
the post-calibration knob, as this could damage the calibration of the bi-metal.
Any tampering will automatically cancel the warrantee given on the product.
6- The heater is on when the pilot lamp is alight. Once the water has reached the
desired temperature, the lamp will switch off. It will come on again automatically
as the heater maintains the water at the desired temperature.
7- Periodically check the temperature in the tank to ensure that your fishes have the
best environment and conditions for spawning.
WARRANTY
With this product we offer you a guarantee of 24 months from the date of
purchase on materials and manufacturing faults. This unit has been manufac-
tured according to the IEC EN 60 335-2-55 Safety Standards, using high quality
materials and the most accurate manufacturing processes to grant the highest
satisfaction and long lasting. This guarantee does not cover any mishandling,
damage or technical modification to the unit. No replacement will be given for
units that have not been properly maintained. The guarantee will be honoured
only if the unit is returned in its whole and together with the receipt or proof of
purchase. In case of returning under guarantee, please return it accompanied
by this certificate of guarantee and the proof of purchase to your supplier. We do
reserve the right to repair or replace the unit. The guarantee does not cover cases
of damages that may result from misuse, tampering and negligence or from not
observing of the Safety Warnings. This guarantee does not cover parts subjected
to natural wearing and tear.
SAFETY WARNINGS
♦ Always disconnect all electrical appliances from the mains before placing
your hands in the water.
♦ Check that the voltage shown on the label of the unit corresponds to the
voltage of the mains supply.
♦ Connect the unit only to power supplies with residual current circuit breaker
(RCCD) with sensitivity of 30 mA.
♦ DO NOT PLUG THE HEATER INTO MAINS SUPPLY UNTIL IT IS IN THE WATER.
♦ The heater must be submersed to at least the “MINIMUM WATER LEVEL”
indication (fig. 1).
♦ After immersion, wait for a few minutes before turning the heater on so that
the thermostat can adapt to the water temperature.
♦ Before removing the heater, or before any changing or adding of water to the
tank, it is recommended to unplug it and to wait at least 10 minutes to cool
down.
♦ The line cord cannot be replaced or repaired. Should the cord become dam-
aged the appliance must be discarded.
♦ Units marked with
on the label are for indoor use only.
♦ This unit must not be used in swimming pools or bathrooms.
IMPORTANT:
Never use the heater out of water or for uses other than in an aquarium/
terrarium. Before removing the heater from the tank, unplug it from
mains and let it cool down. Unplug during all regular maintenance
operations.
IMPORTANT NOTICE
This high quality heater is equipped with a patented post-calibration system that
allows you to re-adjust its setting in case of differences between the temperature on
the scale and the one measured with a precision thermometer.
Should it be necessary, please follow the instructions reported under the following
point 4.
INSTALLATION
To obtain the best distribution of heat in the tank, place the heater inside the
aquarium so that the water can circulate freely around the glass tube, with the
heating element part at the bottom of the aquarium. Otherwise the thermostat
cannot work correctly.
The heater is fully submersible and for correct functioning it must be submersed at
least till the “MINIMUM WATER LEVEL” mark (fig. 1).
1- Mount the suction cups onto the support provided, inserting them as shown in
(fig. 2).
2- Clean the glass surface from algae etc. and press the suction cups firmly against
the glass wall of the aquarium (fig. 3). Allow the heater to acclimatise to the
temperature of your aquarium for about 30 minutes before plugging it in.
3- Turn the blue control knob until the desired temperature shows up in the scale
window (fig. 4). Leave the heater to stabilise for about one full day and check
the temperature of the water with a precision thermometer.
4- In case of a significant difference between the temperature set on the scale and
the one measured with a precision thermometer, please act as follows:
a. Make sure the water is circulating around the heater, trying different posi-
tions or moving plants or items, which could disturb the circulation and let
the heater work for few hours before checking the temperature again. Also
ENGLISH FRANÇAIS DEUTSCH
WARRANTY
GARANTIE
GARANTIE
GARANZIA
GARANTIA
COD. 3323-0100
Disposal:
(in accordance with RL2002/96/EC)
e product must not be added to normal household waste.
It must be disposed of properly.
Gestion des d
é
ch
e
ts:
(directive RL2002/96/EG)
Cet appareil ne doit pas être jeté dans les poubelles domestiques mais
dans les containers spécialement prévus pour ce type de produits.
Entsorgung:
(nach RL2002/96/EG)
Gerät darf nicht dem normalen Hausmüll beigefügt werden, sondern
muss fachgerecht entsorgt werden.
Wichtig für Deutschland: Gerät über Ihre kommunale Entsorgungs-
stelle entsorgen.

Chat with your Eden WaterParadise 425-25 manual using AI

Get instant AI answers from your Eden WaterParadise 425-25 manual

Ask anything about the Eden WaterParadise 425-25. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend WaterParadise 425-25?

Yes No

Frequently Asked Questions

A

Hold the blue control knob steady to keep the scale value fixed. Rotate the orange post-calibration knob towards plus if the measured temperature is lower, or towards minus if it is higher. Each position changes the setting by approximately one degree Celsius. Do not exceed the limits of the calibration range.

Is this answer helpful?

A

No. This unit is designed strictly for aquarium and terrarium use. Using it in swimming pools or bathrooms is dangerous and voids the safety compliance ratings provided by the manufacturer.

Is this answer helpful?

A

Always disconnect all electrical appliances from the mains supply before placing your hands in the water. Unplug the heater before removing it from the tank and allow it to cool down for at least ten minutes.

Is this answer helpful?

A

The manufacturer provides a twenty-four month warranty from the date of purchase. It covers materials and manufacturing faults but excludes damage from misuse, negligence, or unauthorized technical modifications.

Is this answer helpful?

A

The device must be connected to a power supply installed with a residual current circuit breaker with a sensitivity of 0.03 amperes. This ensures safety against electrical shocks during operation.

Is this answer helpful?

A

No, the lamp illuminates only when the heating element is powered on. Once the water reaches the desired temperature, the thermostat cuts the power and the lamp switches off automatically.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Patented post-calibration system allows for precise temperature adjustments based on actual readings.
  • Fully submersible design ensures safety and stable heat distribution within the aquarium.
  • Pilot lamp indicator provides clear visual status on whether the heater is actively running.
  • Complies with IEC EN 60 335-2-55 safety standards for reliable and durable performance.
  • Two year warranty covers manufacturing faults providing peace of mind for the owner.
VS

Disadvantages

  • Power cord cannot be repaired or replaced, requiring full unit replacement if damaged.
  • Indoor use only, making it unsuitable for outdoor ponds or garden pools.
  • Thermostat must be plugged in only after immersion to prevent damage.
  • Disposal must follow specific regulations for electronic waste not household trash.
  • Tampering with calibration knobs voids the warranty and may damage the device.
M: QW-35-FL

Product Specification

Type

Immersion heater

Application

Aquarium, Terrarium

Power

25W

Dimensions

1.30x8.07 in (dia x L)

Features

Saltwater aquarium, temperature controlled, calibratable, 4.92 ft cord

M: QW-35-FL

Product Description

Optimizing Your Aquarium Environment

Maintaining the perfect temperature is crucial for aquatic life survival and overall fish health within any freshwater setup. Tropical fish, in particular, require consistent warmth to thrive without stress. When selecting equipment for your tank, stability is key for long-term success. We recommend analyzing the detailed specifications found in the Eden WaterParadise 425-25 Aquarium Thermostat Heater, 25W, 20.5cm Manual to ensure compatibility. This high-quality heating unit helps provide a suitable habitat by regulating water temperature consistently. It uses patented technology to monitor and adjust heat levels automatically, ensuring no sudden spikes occur during cold nights.

Proper installation is the first step toward success and safety. To achieve ideal heat distribution, place the heater inside the aquarium where water circulates freely around the glass tube. The heating element should point towards the bottom of the tank specifically. Clean the glass surface before attaching the suction cups firmly to ensure a secure hold. Wait for approximately thirty minutes after immersion before connecting the power supply directly. This pause allows the thermostat to adapt to the current water temperature gently without stress. Ensure the device remains submerged past the minimum water level mark at all times during operation.

Precision adjustments are possible with the built-in calibration system for accuracy. If the external thermometer reading differs from the scale, the orange calibration knob allows manual correction. Hold the blue control knob steady to prevent shifting while you work. Rotate the orange knob plus or minus based on the specific difference observed. Each position changes the setting about one degree Celsius effectively. You can adjust within a total range of six degrees safely. This feature ensures long-term accuracy without needing external tools or parts.

Safety and maintenance are vital responsibilities for all owners using this device. Always disconnect the unit from the mains before placing hands in water or performing general cleaning procedures. The device operates safely with a residual current circuit breaker installed in your power outlet. Do not use it in swimming pools or bathrooms as instructed strictly to avoid hazards. The warranty offers coverage for twenty-four months on manufacturing faults only. It excludes misuse or tampering with the calibration knobs or unauthorized repairs. A pilot light indicates function, turning off automatically when temperature is reached. Disposal should follow local electronics recycling laws strictly to protect the environment.

Final Thoughts

Investing in reliable heating equipment protects your livestock from shock. The design focuses on durability and user safety throughout its lifecycle. Regular temperature checks guarantee ideal conditions for spawning and general well-being. Enjoy a thriving aquarium with this dependable heater unit.

M: QW-35-FL

© Copyright 2026 Manual.ly