Manual.ly Logo

Dennerle Nano Corner Filter Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: OA-GPT-5-NAN
page

/ 2

Loading...
e299c671ca913965a8748c80e61844ff908b page 1
Nano Eckfilter / Eckfilter XL D
Leistungsstarker, kompakter Eckfilter für Mini-Aquarien
-
Gebrauchsanleitung vor Inbetriebnahme des Geräts bitte unbedingt aufmerksam und vollständig durchlesen.
G
ut aufbewahren. -
Herzlichen Glückwunsch zum Kauf dieses hochwertigen Produktes aus dem Hause Dennerle.
Wir wünschen Ihnen viel Spaß und Freude an Ihrem Aquarium!
Sicherheitshinweise
• Nur für Wechselstrom 230 V / 50 Hz.
• Nur im Innenbereich verwenden.
•
Vor dem Hineinfassen ins Aquarienwasser stets alle im Wasser befindlichen Geräte vom Netz trennen.
• Der Netzstecker muss nach dem Aufstellen des Gerätes jederzeit zugänglich sein.
• Alle Kabel, die aus dem Aquarium herausführen, und die Netzkabel der Geräte müssen mit einer Tropfschlaufe
versehen sein, so dass eventuell an ihnen herunterlaufendes Wasser nicht in die Geräte bzw. die Netzsteckdose
g
elangen kann.
•
Wenn die Anschlussleitung des Gerätes beschädigt ist, darf das Gerät nicht mehr benutzt werden.
Eine beschädigte Anschlussleitung kann nicht ersetzt werden.
• Maximal zulässige Eintauchtiefe: 50 cm
•
Maximal zulässige Wassertempetratur: 35 °C
1 Lieferumfang und Beschreibung der Komponenten
1 Pumpengehäuse 6 Verbindungsstück
2
Filtergehäuse (zweiteilig), mit Filterelement 7 Winkelstück
Eckfilter XL: 2 Filterelemente 8 Schwämmchen (2 Stück)
3 Einstellknopf für Wasserdurchfluss 9 Reinigungsbürste für Düsenrohr
4 Ausströmrohr, 90° drehbar
5
Düsenrohr mit Reinigungsschieber
2 Installation
• Vor Gebrauch Filtergehäuse abziehen und alle Teile mit warmem Wasser abspülen.
•
Filter in der gewünschten Ecke des Aquariums mit den Saugern befestigen.
• Je nach Anwendungszweck sollte der Filter wie folgt positioniert werden:
2.1 Für Pflanzenaquarien mit CO
2
-Zugabe: Düsenrohr unter der Wasseroberfläche, relativ schwacher Durchfluss. So wird
d
ie Wasseroberfläche nur schwach bewegt und damit unnötige CO
2
-
Verluste vermieden. Den lebenswichtigen Sauerstoff
p
roduzieren die Pflanzen.
2.2 Für Zucht- und Hälterungsaquarien:
Düsenrohr über Wasser, stärkerer Durchfluss. So wird genügend Sauerstoff in das Aquarium eingetragen.
2
.3 Für Paludarien: Filter im Wasserteil liegend anordnen, Düsenrohr mit Winkelstück befestigen.
• Bei Bedarf kann der Raum zwischen Filter und Aquarienecke mit den beiden Schwämmchen verschlossen werden, um zu
v
ermeiden, dass sich Aquarienbewohner darin verirren.
• Der Filter sollte mindestens 2 cm Abstand zum Boden haben, um zu verhindern, dass die Pumpe durch eingesaugten Kies
b
eschädigt wird.
• Die Pumpe darf nie trocken laufen – Gefahr von Motor- und Lagerschäden.
3 Reinigung und Austausch der Filterelemente
Eine Reinigung des Filterelements ist, je nach Belastung, alle 2-6 Wochen erforderlich:
• Netzstecker ziehen.
• Filter aus dem Aquarium nehmen. Filtergehäuse nach unten abziehen.
• Filtergehäuse auseinander ziehen , Filterelemente entnehmen und vorsichtig auswaschen – am besten in einem sauberen
Eimer mit Aquarienwasser, um die wichtigen Filterbakterien nicht zu schädigen.
• Um eine gleichbleibend hohe Filterleistung zu gewährleisten, sollte das Filterelement alle 3-6 Monate ausgetauscht werden.
Ersatz-Filterelemente: Art.-Nr. 5926.
• Eckfilter XL: Wir empfehlen die beiden Filterelemente jeweils abwechselnd zu reinigen bzw. auszutauschen. Dadurch
bleibt stets ein Filterelement biologisch voll aktiv und sorgt für gleichbleibend hohe Wasserqualität.
4 Reinigung von Pumpe, Einstellknopf und Düsenrohr
• Filtergehäuse abziehen.
• Abdeckkappe abnehmen, Rotor herausziehen und alle Teile vorsichtig reinigen – dabei Rotorachse nicht verbiegen!
• Einstellknopf zur Reinigung nach oben abziehen.
• Zur Reinigung des Düsenrohrs integrierten Schieber betätigen , Düsen mit Minibürste reinigen
5 Technische Daten
Netzspannung/Netzfrequenz : AC 230 V / 50 Hz Leistungsaufnahme: 2 W
Max. Pumpenleistung: 150 l/Std. Netzkabel: 1,40 m
IPX8 – wasserdicht
6 Ersatzteile und Zubehör
5926 Ersatz-Filterelement 5865 Ersatz-Filterelement, 3er-Pack 5928 Rotor
5897 Ersatzteil-Set: Düsenrohr, Verbindungsstück, Winkelstück, Schwämmchen, Minibürste
5898 Haltesauger, 6 Stück 5845 Nano FilterModul (befüllbarer Filtereinsatz, anstelle des Filterelements)
5840 Nano FilterExtension (aufsteckbarer, befüllbarer Zusatzfilter)
5846 Nano BabyProtect (aufsteckbarer Ansaugschutz für frisch geschlüpfte Garnelenlarven)
5844 Nano Bio FilterGranulat, 300 ml 5841 Nano ActiveCarbon, 300 ml
5842 Nano AlgenStop Phosphatentferner, 300 ml
7 Garantiebestimmungen
Garantiezeit: 24 Monate (außer Verschleißteile)
Im Garantiefall senden Sie das Gerät bitte zusammen mit dem Kaufbeleg an den Dennerle Kundenservice. Die Garantie um-
fasst Produktions- und Materialfehler. In der Garantiezeit erhalten Sie kostenlosen Ersatz bzw. kostenlose Reparatur defekter
Teile. Voraussetzung ist ein bestimmungsgemäßer Gebrauch des Gerätes. Das Gerät darf innerhalb der Garantiezeit ausschließ-
lich durch den Dennerle Kundenservice geöffnet werden, andernfalls erlischt die Gewährleistung. Weitere Ansprüche über den
Wert des Gerätes hinaus insbesondere z.B. Schäden an Fischen bzw. Pflanzen können nicht anerkannt werden.
Technische Änderungen vorbehalten
Vertrieb: Dennerle GmbH • D-66957 Vinningen
Kundenservice: Dennerle GmbH • Industriestraße 4 • D-66981 Münchweiler www.dennerle.com
Filtre angulaire Nano / filtre angulaire XL F
Filtre angulaire compact à haut rendement pour mini-aquariums
-
Veuillez lire attentivement et intégralement la notice d'utilisation avant la mise en service de l'appareil et la conser-
v
er en un endroit sûr. -
Nous vous félicitons d'avoir acheté ce produit de qualité provenant de la maison Dennerle. DENNERLE vous souhaite
beaucoup de plaisir et de joie avec votre aquarium !
Consignes de sécurité
• Seulement pour du courant alternatif 230 V / 50 Hz.
• Utilisez l’appareil seulement à l'intérieur.
•
Toujours débrancher du secteur tous les appareils se trouvant dans l'eau avant de plonger les mains dans
l'eau de l'aquarium.
• La fiche secteur doit être accessible à tout moment une fois l'appareil placé dans l'aquarium.
• Tous les câbles qui sortent de l'aquarium et les câbles d’alimentation des appareils doivent être assortis d'une
b
oucle d’égouttement, afin que l'eau coulant éventuellement le long de ces câbles ne puisse pas s'introduire
d
ans les appareils ou la prise secteur.
• Si le cordon d'alimentation de l'appareil est endommagé, il convient de ne plus se servir de l'appareil.
Un cordon d'alimentation endommagé ne peut pas être remplacé.
•
Profondeur d'immersion maximale admissible : 50 cm
•
Température d'eau maximale admissible : 35 °C
1 Contenu de livraison et description des composants
1
Boîtier de la pompe 6 Raccord
2 Boîtier du filtre (deux composants), avec élément filtrant 7 Coude
Filtre angulaire XL : 2 éléments filtrants 8 Eponges (2 pièces)
3 Bouton de réglage du débit d'eau 9 Brosse de nettoyage pour buse
4
Tuyau d'évacuation, pivotant sur 90°
5
Buse avec couverde
2 Installation
•
Avant l'usage, enlever le boîtier du filtre et rincer toutes les pièces à l'eau chaude.
• Fixer le filtre dans le coin souhaité de l'aquarium, à l'aide des ventouses.
• Selon son usage, le filtre devrait être positionné comme suit :
2
.1 Pour les aquariums de plantes avec adjonction de CO
2
:
Buse sous la surface de l'eau, débit relativement faible. Ainsi, la
surface de l'eau n'est que faiblement remuée, ce qui évite des pertes inutiles en CO2. Ce sont les plantes qui produisent l'oxygène vital.
2.2 Pour les aquariums d'élevage et de culture :
Buse au-dessus de l'eau, débit plus fort. Cela garantit une oxygénation suffisante de l'aquarium.
2
.3 Pour les paludariums : Disposer le filtre à l'horizontale dans l'eau, fixer la buse avec le coude.
• Si nécessaire, l'espace entre le filtre et le coin de l'aquarium peut être bouché à l'aide des deux éponges afin d'éviter que des
o
ccupants de l’aquarium ne s'y perdent.
• Il convient de placer le filtre à une distance d’au moins 2 cm du sol afin d’éviter que la pompe n'aspire des graviers et ne soit
e
ndommagée.
• La pompe ne doit jamais fonctionner à sec ; cela risquerait d’endommager le moteur et les paliers.
3 Nettoyage et remplacement des éléments filtrants
Un nettoyage des éléments filtrants est nécessaire toutes les 2 à 6 semaines, selon la sollicitation :
• Débrancher la fiche d'alimentation.
• Sortir le filtre de l’aquarium. Tirer le boîtier du filtre vers le bas.
• Ecarter le boîtier du filtre. , enlever les éléments filtrants et les rincer prudemment, de préférence dans un seau propre
rempli d’eau de l’aquarium afin de ne pas nuire aux bactéries de filtration si importantes.
• Pour maintenir le rendement du filtre à un haut niveau, remplacer l'élément filtrant tous les 3 à 6 mois.
Eléments filtrants de rechange : n° d’art. 5926
• Filtre angulaire XL : Nous vous conseillons de nettoyer ou d´échanger les deux éléments filtrants en alternance. Ainsi, un
élément filtrant sera toujours en pleine activité biologique et contribuera à une excellente qualité de l’eau.
4 Nettoyage de la pompe, du bouton de réglage et de la buse
• Enlever le boîtier du filtre.
• Enlever le couverde, retirer le rotor et nettoyer prudemment toutes les pièces, en veillant à ne pas tordre l'axe du rotor !
• Retirer le bouton de réglage vers le haut pour le nettoyer.
• Pour nettoyer la buse, actionner la vanne intégrée , nettoyer la buse à l’aide d’une petite brosse
5 Données techniques
Tension/fréquence du secteur : AC 230 V / 50 Hz Puissance absorbée : 2 W
Rendement maximal de la pompe : 150 l/h Câble d'alimentation : 1,40 m
IPX8 - étanche à l'eau
6 Pièces de rechange et accessoires
5926 Elément filtrant de rechange 5865 Eléments filtrants Pack de 3 5928 Rotor
5897 Pièces de rechange: buse, raccord, coude, petite éponge, petite brosse
5898 6 fixations à ventouse 5845 Nano FilterModul (Crépine à la place de l´élément filtrant pour les filtres angulaires)
5840 Nano FilterExtension (Filtre supplémentaire relevable pour filtre angulaire)
5846 Nano BabyProtect (Grille d´aspiration relevable pour protéger les larves de crevettes fraîchement écloses)
5844 Nano Bio FilterGranulat, 300 ml 5841 Nano ActiveCarbon, 300 ml
5842 Nano AlgenStop Déphosphotant, 300 ml
7 Conditions de garantie
En cas de dommage couvert par la garantie, veuillez renvoyer l'appareil, accompagné de la preuve d'achat, au service après-
vente Dennerle. La garantie couvre les vices de production et de matériau. Les pièces défectueuses seront échangées ou répa-
rées gratuitement pendant la durée de la garantie. La condition requise est une utilisation conforme de l'appareil.
Pendant la période de garantie, l'appareil peut être ouvert exclusivement par le service après-vente de Dennerle, sinon la garan-
tie devient caduque. Aucune réclamation dépassant la valeur des appareils, en particulier des dommages causés p.ex. aux pois-
sons et aux plantes, ne pourra être prise en considération.
Sous réserve de modifications techniques.
Distribution : Dennerle GmbH • D-66957 Vinningen • Allemagne
Service après-vente : Dennerle GmbH • Industriestraße 4 • D-66981 Münchweiler www.dennerle.com
Nano corner filter / corner filter XL
Compact, high-performance corner filter for mini-aquaria
-
Please be sure to read the instructions for use carefully
a
nd in their entirety before using the aquarium for the first time. Keep the instructions in a safe place. -
C
ongratulations on buying this high-quality product from DENNERLE. We wish you lasting enjoyment from your
aquarium!
S
afety instructions
• For 230 V AC / 50 Hz only.
• For indoor use only.
• Always disconnect all devices located in the water from the power supply before placing your hands in the
a
quarium water.
• The mains plug must be accessible at all times after installing the device.
• All cables leading out of the aquarium and the mains leads of the employed devices must be provided with a
d
rip loop to prevent any water which may run down the cables from reaching items of equipment or the mains
s
ocket outlet.
•
Equipment with a damaged connecting lead must no longer be used. A damaged connecting lead cannot be
replaced.
•
Maximum permissible immersion depth: 50 cm
•
Maximum permissible water temperature: 35 °C
1 Scope of delivery and description of components
1
Pump housing 6 Connector
2
Filter housing (two-part), with filter element 7 Elbow
corner filter XL: 2 filter elements 8 Sponge (2 pieces)
3 Setting knob for water flow rate 9 Cleaning brush for nozzle tube
4
Outflow pipe, rotatable by 90°
5
Nozzle tube with cleaning hatch
2 Installation
•
Prior to use, remove filter housing and rinse all parts with warm water.
• Fit filter in the desired corner of the aquarium using the suction clips.
• Depending on the intended purpose for the filter, it should be positioned as follows:
2.1 For plant aquaria with CO
2
supply: Nozzle tube under the water surface, relatively weak flow rate. This results in only
g
entle movement of the water surface, thus avoiding unnecessary losses of CO2. The vital oxygen is produced by the plants.
2.2 For breeding and temporary storage aquaria: Nozzle tube above water, stronger flow of water.
In this way, sufficient oxygen is supplied to the aquarium.
2.3 For paludaria: Place filter in horizontal position in the water area. Secure nozzle tube with elbow.
• Where necessary, the space between the filter and the corner of the aquarium can be closed off with the two sponges, in
order to keep out fish and other creatures which live in the aquarium.
•
The filter should be positioned at least 2 cm away from the bed so that the pump is not damaged by any gravel that is sucked in.
• The pump should never be allowed to run dry – this could damage the motor engine and bearing.
3 Cleaning and replacing the filter elements
The filter elements should be cleaned every 2-6 weeks, depending on the level of contamination:
•
Disconnect the mains plug.
• Remove filter from the aquarium. Remove filter housing by pulling it downwards.
• Pull filter housing apart , Remove filter elements and wash out carefully – ideally in a clean bucket containing aquarium
water, so as to avoid harming the important filtering bacteria.
• In order to maintain a high level of filter performance, the filter element should be replaced every 3-6 months.
Replacement filter elements: Art. no. 5926.
• Corner filter XL: We recommend cleaning and replacing the two filter elements one by one. In this way, one filter element
will remain biologically active, ensuring a constantly high level of water quality.
4 Cleaning the pump, setting knob and nozzle tube
• Remove filter housing.
• Remove cover cap, pull out rotor and clean all parts carefully – avoid bending the rotor axle!
• Pull setting knob upwards to remove for cleaning purposes.
• Clean the nozzle tube by means of the integrated slide , clean nozzles with mini-brush .
5 Technical data
Mains voltage/mains frequency: AC 230 V / 50 Hz Wattage: 2 W
Max. pump delivery rate: 150 l/h Mains lead: 1.40 m
IPX8 – waterproof
6 Spare parts and accessories
5926 Replacement filter element 5865 Filter element pack of 3 5928 Rotor
5897 5897 Spares and accessories set: Nozzle tube, connector, elbow, sponge, mini-brush
5898 6 suction clips 5845 Nano FilterModul (refillable filter cup instead of filter element)
5840 Nano FilterExtension (attachable, refillable auxiliary filter)
5846 Nano BabyProtect (attachable intake protector for freshly hatched shrimp larvae)
5844 Nano Bio FilterGranulat, 300 ml 5841 Nano ActiveCarbon, 300 ml
5842 Nano AlgenStop phosphate remover, 300 ml
7 Guarantee conditions
Guarantee period: 24 months (except wearing parts)
When submitting guarantee claims, please send the equipment to Dennerle's Customer Service department together with
the receipt providing proof of purchase.
The guarantee covers manufacturing and material defects. Defective parts will be replaced or repaired free of charge during the
guarantee period, provided that the equipment has been used only in the correct manner and for the intended purpose.
During the guarantee period, the device may only be opened by Dennerle's Customer Service personnel, otherwise the guarantee
coverage will lapse.
No claims shall be assertible beyond the value of the device, e.g. for damage to fish or plants.
We reserve the right to carry out technical modifications.
Sales / distribution: Dennerle GmbH • D-66957 Vinningen
Customer Service: Dennerle GmbH • Industriestraße 4 • D-66981 Münchweiler, Germany www.dennerle.com
GA_Nano-Eckfilter_EckfilterXL_1211:Layout 1 19.01.2012 09:47 Seite 1

Chat with your Dennerle Nano Corner Filter manual using AI

Get instant AI answers from your Dennerle Nano Corner Filter manual

Ask anything about the Dennerle Nano Corner Filter. Answers come from this manual, with the pages they are based on.

Nano Corner Filter Maintenance Schedule

Remind me when maintenance is due
Every 2-6 weeks
Clean filter elements

Remove filter, take out elements and rinse carefully in aquarium water to protect bacteria.

Every 3-6 months
Replace filter elements

Replace filter element to maintain high performance; use art. no. 5926.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Nano Corner Filter?

Yes No

Frequently Asked Questions

A

It suits nano planted aquaria, breeding and holding tanks, and paludaria. Position the nozzle under the surface for CO2-planted tanks, above for increased aeration, or lay horizontally with the elbow for paludaria.

Is this answer helpful?

A

Clean filter elements every 2–6 weeks depending on load. Replace filter cartridges every 3–6 months to maintain filtration efficiency. For the XL model, alternate cleaning/replacement of the two cartridges so one remains biologically active.

Is this answer helpful?

A

Unplug the unit, remove the housing, take out the rotor and clean parts carefully without bending the rotor axle. Pull the flow control knob up for cleaning and use the integrated slide plus the mini-brush to clean the nozzle openings.

Is this answer helpful?

A

The filter is for indoor use on AC 230 V / 50 Hz, max immersion depth 50 cm, and max water temperature 35 °C. Ensure the mains plug is accessible, use cable drip loops, and never allow the pump to run dry.

Is this answer helpful?

A

Yes. Dennerle offers replacement filter elements, rotors, nozzle sets, suction cups, refillable FilterModul and FilterExtension, BabyProtect intake guards, and media like bio granulate, active carbon and phosphate remover.

Is this answer helpful?

A

Dennerle provides a 24-month warranty against manufacturing and material defects (excluding wear parts). Warranty service requires proof of purchase and opening the device during the warranty period is only permitted by Dennerle service.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Compact corner design saves space and mounts discreetly with suction cups.
  • Low power consumption (2 W) with up to 150 L/h flow — energy-efficient for nano tanks.
  • Adjustable positioning and flow control suit planted, breeding and paludarium setups.
  • Easy maintenance: removable rotor and nozzle with mini brush; spare parts available.
  • XL model offers two filter elements so one can remain biologically active during service.
VS

Disadvantages

  • Limited maximum flow may be insufficient for larger tanks or heavy bio-loads.
  • Requires regular cleaning every 2–6 weeks and element replacement every 3–6 months.
  • Not suitable for outdoor use; only rated for indoor aquaria and 230 V AC systems.
  • Pump must never run dry — risk of motor damage if water level falls unexpectedly.
  • Replacement filter elements and accessories are necessary for optimal performance.
M: OA-GPT-5-NAN

Product Specification

Type

Internal filter

Suitability

Aquariums, Terrariums

Flow rate

39.64 gal/h

Aquarium size

2.64-10.57 gal

Filtration

1x filter fleece (cartridge, Dennerle FilterElement 5926)

Energy consumption

2W

Special features

rotatable filter outlet, 55.12 in connection cable

Manufacturer's warranty

two years

M: OA-GPT-54-NAN

Product Description

Dennerle Nano Corner Filter — Compact, Reliable Internal Filter

The Dennerle Nano Corner Filter is a compact internal corner filter designed for nano aquariums and small paludaria. Available in the standard and XL versions, it combines mechanical and biological filtration in a small, unobtrusive housing that mounts neatly in a tank corner with suction cups. With a low 2 W power draw and a maximum flow of about 150 L/h, it is built for low-energy continuous operation while preserving stable water conditions for plants, shrimp, fry and small fish.

Key features and use cases

Positioning flexibility is a highlight: place the nozzle under the surface for planted tanks with CO2 to minimize surface agitation and CO2 loss, above the surface to increase aeration for breeding or holding tanks, or lay the filter horizontally for paludaria using the elbow adapter. The unit includes a flow control knob, a rotatable outflow pipe, replaceable filter elements (XL has two), small sponges to seal corners, and a mini brush for nozzle maintenance. IPX8 waterproofing and a 1.4 m power cable make installation straightforward.

Maintenance and longevity

Routine care is simple: clean filter media every 2–6 weeks depending on load and replace filter elements every 3–6 months to maintain performance. For the XL model, alternating cleaning or replacement of the two cartridges preserves continuous biological activity. The pump components (rotor, housing, knob and nozzle) can be disassembled for careful cleaning; avoid bending the rotor shaft. Spare parts and accessories are widely available from Dennerle, including refillable filter modules, extensions, protective intake grilles for shrimp larvae and various media (bio granulate, active carbon, phosphate remover).

Safety and specifications

Designed for indoor use on 230 V AC / 50 Hz, maximum immersion depth is 50 cm and max water temperature 35 °C. The unit must never run dry and the mains plug must remain accessible. Cable drip loops are recommended. Warranty covers manufacturing defects for 24 months (wear parts excluded) when used as intended.

Notes

  • Best practice: rinse parts in aquarium water when cleaning to preserve beneficial bacteria.
  • Keep the filter at least 2 cm above the substrate to avoid gravel ingress.
  • Use the provided sponges to close gaps and prevent small animals from entering the filter cavity.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly