Manual.ly Logo

Dennerle BIO-CO2 Bio 120 Manual

5.0 · 1 Ratings

PDF manual · 2 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 2

Loading...
56d3a8123635d66cfc7f0c8820252e853c7d page 1
CO
2
Plant Fertilizer Set Bio 120
Biological CO
2
fertilization for 80 cm aquaria (80-120 l).
With control gel and Mini-Flipper.
What’s what
햲 Thermo container 햵 Bubble counter
햳 Bio CO
2
bottle with starter capsule 햶 Long CO
2
hose (bubble counter – Flipper)
햴 Short CO
2
hose (CO
2
bottle – bubble counter) 햷 CO
2
Mini-Flipper
Set-up and connection
1 Attach the thermo container at a readily accessible point on the aquarium. Remove protective film from adhesive strip. Stick thermo
container in position upright at the top of a clean, grease-free pane of the aquarium and press firmly into place. The entire adhesive
strip of the thermo container must be attached evenly to the pane.
Please note: The thermo container cannot be moved, once it has been pressed firmly into place.
2 Unscrew top of Bio CO
2
bottle, open hinged lid and remove starter capsule. Remove green half of capsule by pulling carefully upwards.
Pour contents of the starter capsule into the CO
2
bottle together with the empty capsule halves.
3 Fill CO
2
bottle up to marking (arrows) with tap water at a temperature of 20 to 25 °C (not over 25 °C!). Screw bottle top firm.
Note: Do not remove the white micro-filter in the hose connector of the top.
4 Break off or cut off hinged lid.
5 Pour tap water into bubble counter until it is 3/4 full.
TIP: For this purpose, submerge the bubble counter in upright position and tap gently on the lid.
6 Use the short hose to connect the CO
2
bottle to the long tube of the bubble counter, fit hose firmly.
7 Fit long hose to the 2nd connector (without tube) of the bubble counter.
8 Place CO
2
bottle together with the connected bubble counter into the thermo container from above.
9 Place top on thermo container. Align bubble counter so that it fits into the recess provided in the top.
10 Rinse Mini-Flipper with warm tap water (no detergents!).
11 Fit CO
2
supply hose firmly to hose connector of the Mini-Flipper.
12 Choose a spot in the aquarium which is as dark as possible (to prevent algae growth) and where the water movement is good. Fix
Flipper in the aquarium in vertical position, at least 5 cm below the surface of the water.
When the system is applied correctly, CO
2
production will begin within 24-48 hours and at a rate of 6-10 bubbles per minute your aqua-
rium will be supplied with CO
2
for at least 30 days. The running-in period for the Flipper is approx. 2 days. A biofilm will form
over this period, enabling the CO
2
bubbles to pass freely through the device.
Changing the CO
2
bottle
When bubbles no longer issue from the Mini-Flipper, this indicates that the CO
2
bottle is empty. Proceed as follows:
• Remove CO
2
bottle from thermo container and disconnect hose from bottle top.
• Activate and connect new Bio CO
2
bottle.
The contents of the used CO
2
bottle can be disposed of via the sewerage system.
Cleaning the CO
2
Mini-Flipper
• Remove collector. Place Mini-Flipper flat in your hand so that the suction clips are pointing to the right. The open side (collector base)
is pointing upwards. Slide front side panel of the Flipper upwards by approx. 2 cm.햿
• Fold out side panel. Take out CO
2
hose, do not pull out. Clean all parts with water and soft brush. Do not use any detergents. Reassemble
Mini-Flipper via the reverse procedure. Insert CO
2
hose back in the side panel such that the end is located at the bottom stop. 헀
What if ... – Troubleshooting
Special information
Shelf life in unopened condition: Bottle contents approx. 5 years; starter capsules: approx. 12 months at 20 °C, approx. 19 months at
10 °C. Consequently, please store Bio CO
2
bottles in cool and dry conditions. Protect from sunlight, heat and frost!
Important:
• Should larger quantities of the bottle contents accidentally enter into the aquarium water during operation of the Bio CO
2
fertilizer
system, this may cloud the water and lead to oxygen deficiency. In this case, part of the water should be replaced immediately and the
fertilizer system should be checked for correct functioning. For this reason, do NOT fill the CO
2
bottle beyond the marking (arrows)!
Always use the thermo container in its support, to prevent it from falling over!
• Always keep CO
2
bottle out of the reach of children and in an upright position!
Spare parts (available from specialist retailers)
3004 Bio CO
2
bottle 3071 CO
2
Mini-Flipper
1557 5 starter capsules 1515 2 Longlife suction clips, green
Set CO
2
de fertilisation des plantes Bio 120
Fumure biologique au CO
2
pour aquariums de 80 cm (80-120 l).
Avec gel de contrôle et mini-Flipper.
Explications
햲 Récipient thermique 햵 Compte-bulles
햳 Dépôt de réserve de CO
2
bio avec capsule de démarrage 햶 Flexible CO
2
long (compte-bulles - Flipper)
햴 Flexible CO
2
court (dépôt de réserve - compte-bulles) 햷 Diffuseur CO
2
Mini-Flipper
Structure et raccordement
1 Fixez le récipient thermique à un endroit de l’aquarium aisément accessible. Détachez le film protecteur des bandes adhésives. Collez le
récipient thermique en haut de l’aquarium, à la verticale, sur une vitre propre et dégraissée et appuyez fermement. Tout le pourtour du
récipient thermique doit être uniformément plaqué sur la vitre.
Important: Une fois que vous aurez appuyé, vous ne pourrez plus déplacer le récipient thermique.
2 Dévissez le couvercle du dépôt de réserve de CO
2
bio, ouvrez le couvercle rabattable et prélevez la capsule de démarrage. Retirez la
moitié verte de la capsule prudemment vers le haut. Versez le contenu de la capsule et les moitiés vides dans le dépôt de réserve.
3 Remplissez le dépôt de réserve jusqu’au trait de marquage (flèche) avec de l’eau de distribution entre 20 et 25°C (pas plus de 25°C!).
Revissez fermement le couvercle. CONSEIL :
N’enlevez pas le micro-filtre blanc du raccord pour flexible du couvercle.
4 Détachez ou découpez le couvercle rabattable.
5 Remplir le compte-bulles à trois quarts d'eau de distribution.
Conseil : Plongez le compte-bulles à la verticale dans l’eau et frappez légèrement sur le couvercle
6 Raccordez le dépôt de réserve à l’aide du flexible court au long tube du compte-bulles, placez le flexible fermement.
7 Raccordez le flexible long au second raccord (sans tube) du compte-bulles.
8 Placez le dépôt de réserve avec le compte-bulles raccordé dans le récipient thermique (par le haut)
9 Placez le couvercle sur le récipient thermique. Orientez le compte-bulles de sorte à ce qu’il s’encastre dans le logement du couvercle
prévu à cet effet.
10 Rincez le mini-Flipper à l’eau chaude de distribution (n’utilisez pas de produit de nettoyage!)
11 Placez fermement le flexible d’alimentation en CO
2
sur le raccord du mini-Flipper.
12 Choisissez dans l’aquarium un emplacement le plus sombre possible (afin d’éviter la formation d’algues) avec un bon brassage d’eau.
Fixez le Flipper dans l’aquarium à la verticale
, à 5 cm au moins en dessous du niveau de l'eau.
Si les conditions d’utilisation sont respectées, la production de CO
2
commence dans un délai de 24 à 48 heures et alimente votre aquarium
pendant au moins 30 jours à un réglage de 6-10 bulles par minute. Le temps de rodage du Flipper est d'environ deux jours. Un
film biologique se forme dans l’intervalle, ce qui permet aux bulles de CO
2
de passer sans obstacle.
Changer le dépôt de réserve de CO
2
bio
Si aucune bulle n’apparaît plus dans le mini-Flipper, c’est le signe que le dépôt de réserve est épuisé. Dans ce cas:
• Retirez le dépôt de réserve du récipient thermique et ôtez le flexible du couvercle.
• Démarrez un nouveau dépôt de réserve de CO2 bio et raccordez-le.
Vous pouvez jeter le contenu du dépôt de réserve usagé dans les canalisations domestiques.
Nettoyage du diffuseur CO
2
Mini-Flipper
• Enlever le collecteur. Poser le Mini-Flipper dans la main de sorte à ce que les ventouses soient tournées vers la droite. Le côté ouvert
(logement du collecteur) est dirigé vers le haut. Déplacez d’environ 2 cm vers le haut la face latérale avant. 햿
•
Plier la face latérale vers l'extérieur. Enlever le tuyau CO
2
, sans tirer dessus. Nettoyer tous les éléments avec de l'eau chaude et une
brosse douce, n'utiliser aucun produit d'entretien. Remonter le Flipper dans l'ordre inverse. Replacer le tuyau CO
2
dans la face
latérale de manière à ce que l'extrémité se trouve sur la butée inférieure.헀
Défauts et solutions - élimination des erreurs
Remarques particulières
Conservation dans son emballage fermé: contenu de la bouteille environ 5 ans ; capsules de démarrage : environ 12 mois à 20°C, envi-
ron 18 mois à 10°C. Privilégier donc la conservation du dépôt de réserve de CO
2
bio dans un endroit frais et sec. Protéger du soleil, de la
chaleur et du gel!
Attention !
• Si de grandes quantités du contenu de la bouteille venaient à se déverser dans l’aquarium pendant l’utilisation de l’installation de fumure CO
2
bio, cela
peut troubler l’eau et entraîner un manque d’oxygène. Dans ce cas, effectuez immédiatement un changement partiel de l’eau et vérifiez le bon fonc-
tionnement de l’installation de fumure. Conclusion: Ne PAS dépasser le marquage (flèche) du dépôt de réserve lors du remplissage! Toujours utiliser la
bouteille dans le récipient thermique afin d’éviter qu’elle ne se renverse!
• Veuillez conserver le dépôt de réserve de CO
2
bio à la verticale et hors de portée des enfants!
Pièces de rechange (disponibles dans les magasins spécialisés)
3004 Dépôt de réserve de CO
2
bio 3071 Diffuseur CO
2
Mini-Flipper
1557 5 capsules de démarrage 1515 Ventouses Longlife, vertes, 2 pièces
CO
2
Pflanzen-Dünge-Set Bio 120
Biologische CO
2
-Düngung für 80 cm Aquarien (80-120 l).
Mit Control-Gel und Mini-Flipper.
Was ist was
햲 Thermobehälter 햵 Blasenzähler
햳 Bio CO
2
Vorrats-Depot mit Starterkapsel 햶 Langer CO
2
Schlauch (Blasenzähler - Flipper)
햴 Kurzer CO
2
Schlauch (Vorrats-Depot – Blasenzähler) 햷 CO
2
Mini-Flipper
Aufbau und Anschluss
1 Befestigen Sie den Thermobehälter an einer gut zugänglichen Stelle am Aquarium. Schutzfolie von Klebestreifen abziehen.
Thermobehälter oben am Aquarium, senkrecht an eine saubere, fettfreie Scheibe ankleben und fest andrücken. Der Thermobehälter
muss rundherum gleichmäßig an der Scheibe anliegen.
Bitte beachten: Nach dem Andrücken lässt sich der Thermobehälter nicht mehr verschieben.
2 Deckel vom Bio CO
2
Vorrats-Depot abschrauben, Klappdeckel öffnen und Starterkapsel herausnehmen. Grüne Kapselhälfte vorsichtig
nach oben abziehen. Inhalt der Starterkapsel und leere Kapselhälften in das Vorrats-Depot geben.
3 Vorrats-Depot bis zum Markierungsstrich (Pfeile) mit 20 bis 25 °C warmem Leitungswasser füllen (nicht über 25 °C!). Deckel fest
zuschrauben. Hinweis:
Den weißen Mikro-Filter im Schlauchanschluss des Deckels nicht entfernen.
4 Klappdeckel abbrechen oder abschneiden.
5 Blasenzähler zu 3/4 mit Leitungswasser füllen.
TIPP: Blasenzähler dazu senkrecht unter Wasser tauchen und leicht auf den Deckel klopfen.
6 Vorrats-Depot mit dem kurzem Schlauch an das lange Röhrchen des Blasenzählers anschließen, Schlauch fest aufstecken.
7 Den langen Schlauch auf den 2. Anschluss (ohne Röhrchen) des Blasenzählers stecken.
8 Vorrats-Depot zusammen mit dem angeschlossenen Blasenzähler von oben in den Thermobehälter stellen.
9 Deckel auf Thermobehälter setzen. Blasenzähler dabei so ausrichten, dass er in die vorgesehene Aussparung des Deckels passt.
10 Mini-Flipper mit warmem Leitungswasser (ohne Reinigungsmittel!) abspülen.
11 CO
2
Zuleitungsschlauch auf den Schlauchanschluss des Mini-Flippers fest aufstecken.
12 Im Aquarium eine möglichst dunkle Stelle (beugt Veralgung vor) mit guter Wasserbewegung wählen. Flipper senkrecht
, mindestens
5 cm unter dem Wasserspiegel im Aquarium befestigen.
Die CO
2
-Produktion beginnt bei richtiger Anwendung innerhalb 24-48 Stunden und versorgt Ihr Aquarium, bei 6-10 Blasen pro Minute,
mindestens 30 Tage mit CO
2
. Die Einlaufzeit des Flippers beträgt ca. 2 Tage. In dieser Zeit bildet sich ein Biofilm, der den CO
2
-Blasen
das ungehinderte Durchlaufen ermöglicht
Bio CO
2
Vorrats-Depot wechseln
Wenn im Mini-Flipper keine Blasen mehr austreten, ist das Vorrats-Depot verbraucht, dann:
• Vorrats-Depot aus Thermobehälter nehmen und Schlauch vom Deckel abziehen.
• Neues Bio CO
2
Vorrats-Depot starten und wieder anschließen.
Der Inhalt des verbrauchten Vorrats-Depots kann über die Hauskanalisation entsorgt werden.
CO
2
Mini-Flipper reinigen
• Auffangwanne abziehen. Mini-Flipper so in die Hand legen, dass die Sauger nach rechts zeigen. Die offene Seite (Sitz der
Auffangwanne) zeigt nach oben. Vordere Seitenwand des Flippers ca. 2 cm nach oben verschieben. 햿
• Seitenwand herausklappen. CO
2
-Rohr herausnehmen, nicht herausziehen. Alle Teile mit warmem Wasser und weicher Bürste reinigen,
keine Reinigungsmittel verwenden. Flipper in umgekehrter Reihenfolge wieder zusammenbauen. CO
2
-Rohr wieder so in Seitenwand ein-
legen, dass sich das Ende am unteren
Anschlag befindet. 헀
Was tun wenn... - Fehlerbehebung
Besondere Hinweise
Haltbarkeit in ungeöffnetem Zustand: Flascheninhalt ca. 5 Jahre; Starterkapseln: ca. 12 Monate bei 20 °C, ca. 18 Monate bei 10 °C.
Deshalb Bio CO
2
Vorrats-Depot bitte kühl und trocken lagern. Vor Sonne, Hitze und Frost schützen!
Achtung!
• Sollten während des Betriebs der Bio CO
2
-Düngeanlage versehentlich größere Mengen des Flascheninhalts ins Aquarium gelangen, so
kann dies zu Wassertrübung und Sauerstoffmangel führen. In diesem Fall sofort entsprechenden Teilwasserwechsel durchführen und
sachgerechte Funktion der Düngeanlage überprüfen. Deshalb: Vorrats-Depot NICHT über Markierungsstrich (Pfeile) füllen! Flasche stets
in Thermobehälter betreiben, um ein Umfallen zu verhindern!
• Bio CO
2
Vorrats-Depot für Kinder unerreichbar und immer stehend aufbewahren!
Ersatzteile (im Fachhandel erhältlich)
3004 Bio CO
2
Vorrats-Depot
3071 CO
2
Mini-Flipper
1557 5 Starterkapseln
1515 2 Longlife-Sauger, grün
D
Vertrieb: Dennerle GmbH, D-66957 Vinningen • Kundenservice: Dennerle GmbH, Industriestraße 4, D-66981 Münchweiler • www.dennerle.com
F
Vente: Dennerle GmbH, D-66957 Vinningen • Service après - ventes: Dennerle GmbH, Industriestraße 4, D-66981 Muenchweiler • www.dennerle.com Sales: Dennerle GmbH, D-66957 Vinningen • Kundenservice: Dennerle GmbH, Industriestraße 4, D-66981 Muenchweiler • www.dennerle.com
GB
Fehler
Nach 48 Stunden
keine Blasen im
Flipper zu sehen.
CO
2
-Blasen laufen
nicht ungehindert
im Flipper hoch
Ursache
Deckel des Vorrats-Depots oder Schlauchverbindung undicht.
CO
2
-Produktion noch nicht angesprungen, da Vorrats-Depot zu
kühl
Starterkapsel hat Gärprozess nicht richtig in Gang gebracht.
Flipper nicht senkrecht montiert.
Flipper noch in der Einlaufphase.
Hindernis im Flipper (Algen, Mulm, Schnecken)
Behebung
Deckel fest zuschrauben, Schlauch fest aufstecken.
Prüfen: Hat Thermobehälter rundherum gleichmäßigen
Kontakt zur Aquariumscheibe? Nach 48 Stunden CO
2
-
Produktion erneut prüfen.
Vorrats-Depot mit einer 2. Kapsel (im Fachhandel erhältlich)
neu starten.
Flipper senkrecht montieren.
Ende der Einlaufphase abwarten (ca. 2 Tage).
Flipper reinigen.
Erreur
Aucune bulle ne
s’échappe visible-
ment du Flipper
au bout de
48heures
Les bulles de CO
2
ont du mal à
monter du
Flipper
Cause
Le couvercle du dépôt de réserve ou le raccordement du flexi-
ble n’est pas hermétique.
La production de CO
2
n’est pas encore démarrée car le dépôt
de réserve est trop froid.
La capsule de démarrage n’a pas encore lancé le processus de
fermentation.
Le Flipper n'est pas monté verticalement.
Le Flipper se trouve encore dans la phase de rodage.
Obstacle à l’intérieur du Flipper (algues, boue, escargots)
Solution
Vissez fermement le couvercle, fixez bien les flexibles.
Contrôlez : Le pourtour du récipient thermique est-il bien pla-
qué uniformément sur la vitre de l’aquarium?
Recontrôler la production de CO
2
48 heures plus tard.
Redémarrez le dépôt de réserve avec une 2e capsule (dispo-
nible dans votre magasin spécialisé).
Monter le Flipper verticalement.
Attendre la fin de la phase de rodage (environ 2 jours).
Nettoyer le Flipper..
Fault
No bubbles visi-
ble in the Flipper
after 48 hours.
CO
2
bubbles do
not rise freely
through the
Flipper.
Cause
Top of CO
2
bottle or hose connectors leaking.
CO
2
production not yet started, as CO
2
bottle too cool.
Starter capsule has not triggered fermentation process
correctly.
Flipper not installed in vertical position.
Flipper still in running-in phase.
Blockage in Flipper (algae, sludge, snails)
Remedy
Screw top firm, fit hoses firmly.
Check: Is thermo container evenly attached to aquarium pane
all round? Check CO
2
production again after 48 hours.
Start CO
2
bottle again with a 2nd capsule (available from
dealers).
Fit Flipper in an upright position.
Await end of running-in phase (approx. 2 days).
Clean Flipper.
햿
헀


쐅
쐈
쐉

Chat with your Dennerle BIO-CO2 Bio 120 manual using AI

Get instant AI answers from your Dennerle BIO-CO2 Bio 120 manual

Ask anything about the Dennerle BIO-CO2 Bio 120. Answers come from this manual, with the pages they are based on.

BIO-CO2 Bio 120 Maintenance Schedule

Remind me when maintenance is due
Monthly
Replace CO2 bottle when empty

When no bubbles issue from the Mini-Flipper, remove the empty bottle and connect a new Bio CO2 bottle.

As needed
Clean the CO2 Mini-Flipper

Disassemble and clean all parts with warm water and a soft brush; do not use detergents.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend BIO-CO2 Bio 120?

Yes No
0
User Pic

Lukas Weber

5 months ago

Is this CO2 system suitable for medium aquariums and does it really improve plant growth?

0
User Pic

Manual.ly

5 months ago

Yes, this system is designed for medium-sized aquariums and works well for beginners and experts. Users have confirmed significantly better plant growth. It delivers stable CO2 levels for healthy aquatic plants.

M: qwen/qwen3.5-flash-20260224
M: qwen/qwen3.5-flash-20260224

Frequently Asked Questions

A

Each Bio CO2 bottle is designed to supply your aquarium with CO2 for at least 30 days once activated. This ensures consistent fertilization levels for your aquatic plants without frequent replacements, provided the system is set up correctly according to the specified bubble rate targets.

Is this answer helpful?

A

The set is specifically designed for 80 cm aquaria with a water volume ranging from 80 to 120 liters. This size compatibility ensures that the biological production of carbon dioxide matches the needs of plants within tanks of this specific capacity range effectively.

Is this answer helpful?

A

Once the system is applied correctly, CO2 production will begin within 24 to 48 hours. The Mini-Flipper diffuser also has a running-in period of approximately two days for a biofilm to form, which enables bubbles to pass freely through the device for optimal absorption.

Is this answer helpful?

A

Unscrew the top of the Bio CO2 bottle and remove the starter capsule. Pour the contents of the capsule into the CO2 bottle along with tap water at a temperature of 20 to 25 degrees Celsius. Do not remove the white micro-filter in the hose connector on the bottle top during this process.

Is this answer helpful?

A

If bubbles are not visible after 48 hours, check if the bottle is too cool or if connections are leaking. You can restart the production with a 2nd capsule. Ensure the Mini-Flipper is mounted vertically and clean any blockages like algae or sludge from the internal parts of the diffuser.

Is this answer helpful?

A

No, do not use detergents when cleaning the CO2 Mini-Flipper. Use warm tap water and a soft brush to clean all parts. Detergents may leave residues that are harmful to the aquatic environment or interfere with the biological processes within the aquarium water.

Is this answer helpful?

A

Keep the bottle contents out of direct sunlight, heat, and frost. Unopened bottle contents last about 5 years. Starter capsules last about 12 months at 20 degrees Celsius or up to 18 months at 10 degrees Celsius. Always store in cool, dry, and upright positions away from children.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Biological system requires no electricity or expensive equipment for CO2 generation
  • Effective for 80 to 120 liter aquariums with a duration of at least 30 days per bottle
  • Includes a Mini-Flipper diffuser for efficient bubble dispersion and reduced algae risk
  • Simple setup process with clear instructions for aquarium maintenance and safety
  • Long shelf life for stored components when kept in cool and dry conditions
VS

Disadvantages

  • Requires manual mixing of starter capsules and water for activation before use
  • Sensitive to temperature changes, needing a range of 20 to 25 C for optimal function
  • Overfilling the bottle can cause liquid spills leading to oxygen deficiency in the tank
  • The flipper requires a two-day running-in period before efficient gas flow is achieved
  • Capsules have a limited lifespan of 12 to 18 months depending on storage temperature
M: qwen/qwen3.5-flash-20260224

Product Specification

Application

CO2 Supply, Plant Fertilization

Type

CO2 Fertilizer System (Storage Tank with Thermal Insulation, Starter Capsules, Bubble Counter, Control-Gel, Unregulated, with CO2 Dosing Device Mini-Flipper), Complete Set, BIO-CO2

Specifications

Approx. 30 Days Operating Duration

Suitability

Freshwater, Aquarium, 21.13-31.70 gal

Consumables

BIO-CO2 Control-Gel

Features

Includes CO2 Tubing

M: qwen/qwen3.5-flash-20260224

Product Description

Enhancing Your Planted Aquarium with the Dennerle BIO-CO2 Plant Fertilizer Set Bio 120

Achieving lush growth in your aquarium can be challenging without adequate carbon dioxide. The Dennerle BIO-CO2 Plant Fertilizer Set Bio 120 offers a reliable biological solution for plant enthusiasts. Designed specifically for 80 cm aquaria ranging from 80 to 120 liters, this system ensures consistent CO2 supply without complex equipment or electricity.

The core of this setup relies on biological fermentation. You mix a starter capsule with water and yeast in a special bottle. This reaction produces CO2 bubbles over time. The system includes a thermo container to maintain optimal temperature for the reaction. A bubble counter allows you to monitor the production rate, ensuring it stays within the recommended 6 to 10 bubbles per minute. The Mini-Flipper diffuser creates fine bubbles for better absorption by plants. The bubble counter and flipper are key components for efficiency.

Setting up the system is straightforward according to guidelines. First, attach the thermo container to a clean, grease-free part of the aquarium glass using the adhesive strip. Ensure the strip is fully adhered. Next, prepare the bottle by removing the capsule lid and pouring contents into the water-filled bottle. Fill only up to the markings with tap water between 20 and 25 degrees Celsius. Assemble the hoses connecting the bottle to the counter and finally to the flipper. Place everything inside the thermo box and align the bubble counter correctly.

Once activated, CO2 production begins within 48 hours. Each bottle lasts for at least 30 days. The Mini-Flipper requires a two-day running-in period for a biofilm to form, which prevents algae blockage. Position the flipper vertically at least 5 cm below the surface in a spot with good water movement. Maintenance involves regular cleaning of the flipper with warm water and no detergents. If bubbles stop, check for leaks or cool bottles. Troubleshooting is essential for continuous operation.

Storage is crucial for longevity. Unopened bottles last five years, while starter capsules last between 12 to 18 months depending on temperature. Keep supplies away from children and direct sunlight. Avoid overfilling the bottle to prevent liquid spills that could cause oxygen deficiency in the tank. If liquid enters the tank, replace water immediately to prevent safety risks.

This system is perfect for beginners seeking simplicity. It balances cost and performance effectively. By following proper setup and maintenance routines, your aquarium plants will thrive with stable fertilization levels. Spare parts are available for replacement bottles and flipper clips if needed. Codes like 3004 and 3071 ensure compatibility.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly