Manual.ly Logo

Cane Creek eeSilk+ Carbon Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: gpt-5.6-terra
page

/ 2

Loading...
784dcdebbf5c958b8d14484797d3ae6856e1 page 1
1. Confirm your frame has the correct diameter
seat tube for your new eeSilk
+
seatpost. eeSilk
+
seatposts are available in 27.2mm and 31.6mm
post diameter but Cane Creek offers several
seatpost adapters to accommodate larger size
seat tubes.
2. eeSilk
+
: Grease shim (if applicable) and
seatpost before installing into frame. DO NOT
lubricate seat tubes of carbon frames unless
specified by the manufacturer.
eeSilk
+
Carbon: Cane Creek recommends
using carbon fiber paste with the carbon post.
For carbon frames, ensure the carbon paste is
approved by the manufacturer.
3. Insert shim (if applicable) into the bicycle
frame with the split aligned with the split in
the seat-tube.
4. Install eeSilk
+
seatpost into the bicycle frame
to approximately the correct height using
the height indicators on the back of the post
and fasten the seatpost clamp to the frame
manufacturers specifications. Confirm the seatpost is installed so that
the minimum insertion line
is not exposed above the seat tube of the bicycle frame.
5. Loosen the two saddle clamp bolts until the threads are barely
engaging the Barrel Nut and the Spherical Nut. Be sure grease is
applied to the interface between the lower clamp and cradle.
6. Place one rail of the saddle in position between the upper and lower
clamps. Then rotate saddle so the other rail slips over the far edge
of the upper clamp and into position in the rail grooves of the lower
clamp. eeSilk
+
seatposts are designed to accommodate 7mm diameter
metal seat rails and 7mm by 9mm oval composite seal rails.
7. Begin to tighten the front and rear clamp bolts. The saddle tilt is
controlled by these two bolts. Check that the saddle tilt and position
of the saddle are correct before final tightening. The front bolt can
be adjusted by hand, a 4mm hex, or 17mm wrench on eeSilk
+
Carbon
or a 10mm wrench on eeSilk
+
. The rear bolt must be tightened to
44in*lb (5.0 N*m). The front bolt must receive an additional half turn of
preload once the rear bolt has been properly torqued.
8. Adjust saddle height if necessary.
355 Cane Creek Rd, Fletcher NC USA 28732
canecreek.com | 828-641-9560
7
17
13
14
8
16
10
15
5
9-1
11
6
2
12
4
3
1
ID Number Qty
1 AAE0096Ti
2 AAE0135
3 AAE0120
4 AAE0089
5 AAE0088
6 AAE0280
7 AAE0282
8 AAE0281
9-1 AAE0289
9-2 AAE0286
9-3 AAE0291
9-4 AAE0290
10 AAE0285
11 AAE0300
12 AAE0283SS
13 AAE0097Ti
14 AAE0090
15 AAE0115
16 AAE0313
17 AAE0323
1* AAE0302
Description
M6 x 1 x 33 Thumb Bolt - Ti
Barrel Nut 15.5mm - SS
Spherical Washer M6
Upper Clamp
Lower Seat Clamp
Clamp Cradle
Removable Axle
Press Axle
Carbon Post - 27.2 x 350
Aluminum Post - 27.2 x 375
Carbon Post - 31.6 x 350
Aluminum Post - 31.6 x 375
O-ring 7.8x1.9 - NBR
Arm Bushing
Axle Bolt
M5 x 0.8 x 33 Bolt - Ti
Spherical Washer M5
Spherical Nut
Arm
Elastomer - Medium
M6 x 1 x 32 - 10mm Hex
1
1
1
1
1
1
1
3
1
1
1
1
4
8
1
1
1
1
2
1
1
1*
Saddle
Rails
4mm HEX
Loosen
Grease these
surfaces
if nessesary
Loosen or remove
Seatpost Installation Instructions

Chat with your Cane Creek eeSilk+ Carbon manual using AI

Get instant AI answers from your Cane Creek eeSilk+ Carbon manual

Ask anything about the Cane Creek eeSilk+ Carbon. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend eeSilk+ Carbon?

Yes No

Frequently Asked Questions

A

This version uses a 27.2 mm post diameter. Confirm that your frame has a 27.2 mm seat tube, or use a suitable Cane Creek adapter for a larger compatible seat tube.

Is this answer helpful?

A

The seatpost is supplied with a Medium elastomer installed. Extra Soft, Soft, Firm, and Extra Firm options are available separately for riders who need a different suspension response.

Is this answer helpful?

A

No. It is designed to absorb small bumps and vibration. For large obstacles on the road or trail, riders should stand up rather than remain seated.

Is this answer helpful?

A

The clamp is designed for 7 mm diameter metal saddle rails and 7 x 9 mm oval composite saddle rails. Check rail dimensions before installation.

Is this answer helpful?

A

Cane Creek recommends carbon fiber paste with the carbon post. If the bicycle has a carbon frame, ensure the paste is approved by the frame manufacturer and keep the minimum insertion line inside the seat tube.

Is this answer helpful?

A

The maximum allowable rider weight is 250 lb (113 kg). Choose and install the correct elastomer for rider weight and intended use before riding.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Carbon 27.2 mm post combines lightweight construction with suspension comfort for small, repetitive bumps.
  • Interchangeable elastomers let riders tune support for weight, riding style, and preferred feel.
  • Compatible with 7 mm round metal rails and 7 x 9 mm oval composite saddle rails.
  • Parallelogram suspension is suited to improving comfort on pavement, gravel, and light trails.
VS

Disadvantages

  • Designed for small bumps only; riders must stand for large obstacles and significant impacts.
  • Extra Soft, Soft, Firm, and Extra Firm elastomers are sold separately.
  • Requires careful torque settings, correct minimum insertion, and appropriate carbon assembly paste.
  • Maximum allowable rider weight is 250 lb (113 kg).
M: gpt-5.6-terra

Product Specification

Type

Suspension seatpost

Color

black

Material

Carbon

Length

14.25 in

Setback

0.47 in

Diameter

1.07 in

Weight

0.71 lb

M: gpt-5.6-terra

Product Description

Cane Creek eeSilk+ Carbon 27.2mm Suspension Seatpost - Read, Download & Print Free

The Cane Creek eeSilk+ Carbon 27.2mm suspension seatpost is designed to bring added comfort and control to compatible bicycles by smoothing the small, repetitive bumps that can make long rides tiring. Its carbon post construction is paired with a parallelogram-style suspension system, helping the saddle move in response to rough pavement, gravel, and light trail chatter while preserving a stable riding position.

Tunable support for different riders

A Medium elastomer comes installed, and riders can tailor suspension feel with separately available Extra Soft, Soft, Firm, and Extra Firm elastomers. This allows the seatpost to be matched to rider weight, riding style, and personal comfort preferences. The recommended maximum rider weight is 250 lb (113 kg), and the correct elastomer should be fitted before riding.

The eeSilk+ is intended for absorbing small bumps rather than large impacts. Riders should still rise from the saddle when approaching major obstacles on roads or trails. This practical setup makes it a strong option for endurance-focused riders who want less vibration without changing the character of their bike.

Installation and saddle adjustment

Before installation, confirm that the frame accepts a 27.2 mm seatpost or uses an appropriate adapter. Cane Creek recommends carbon fiber paste for the carbon post, while carbon-frame owners should use only paste approved by their frame manufacturer. The minimum insertion line must remain inside the bicycle seat tube.

The saddle clamp accepts standard 7 mm metal rails as well as 7 x 9 mm oval composite rails. Saddle tilt is adjusted through the front and rear clamp bolts. The rear bolt requires a 5.0 Nm torque setting, followed by an additional half turn of preload at the front bolt after the rear bolt is correctly tightened.

Care and setup notes

Periodically inspect the axle hardware and confirm that it remains secure. Pivot axles may be lubricated with a light oil when needed. Elastomer changes require basic hex tools and careful reassembly, including tightening the small axle bolt to 4.0 Nm.

Note: Use the seatpost only within its stated rider-weight limit and select the appropriate elastomer before every first ride after a setup change. Cane Creek provides a one-year limited warranty for defects in materials or workmanship for the original owner.

M: gpt-5.6-terra

© Copyright 2026 Manual.ly