Manual.ly Logo

Candy CHW6LBX Manual

0.0 · 0 Ratings

PDF manual · 62 Pages

English

M: QW-35-FL
page

/ 62

Loading...
7c7abb8ba358efdbcc9330eb9b9ead5361a7 page 4
Table A
Burner Type
Ø pan/pot
(cm)
AUX
SR
R
10 - 18
12 - 22
16 - 26
Auxiliary
Semi Rapid
Rapid
Power
(kW)
1,00
1,75
2,70
G20/20 mbar
(methane)
95 l/h
167 l/h
257 l/h
G30/28-30 mbar
(LPG)
73 g/h
127 g/h
196 g/h
04 GB
2.3. ADAPTING THE HOB TO DIFFERENT
TYPES OF GAS
To adapt the Hob for use with different types of gas, carry out the
following instructions:
•Remove the grids and burners
•Insert on hexagonal spanner (7 mm) into the burner support (Figure
7)
•Unscrew the injector and replace it with one suitable for the gas to be
used (see gas type table)
2.4. REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob to the minimum setting
and then remove the knob (this can easily be removed by applying
gentle pressure).
Using a small «Terminal» type screwdriver the regulating screw can
be adjusted as in Turning the screw clockwise reduces theFigure 9.
gas flow, whilst turning it anticlockwise increases the flow – Use this
adjustment to obtain a flame of approximately 3 to 4 mm in length and
then replace the control knob.
When the gas supply available is LPG - the screw to set the idle flame
must be turned (clockwise) to the end stop.
When you have carried out the new gas regulation, replace the old gas
rating plate on your appliance with one (supplied with hob) suitable for
the type of gas for which it has beenregulated.
3. USE OF HOB - USER INSTRUCTIONS
This appliance must only be used for the purpose for which it is
intended, domestic cooking, and any other use will be considered
improper and could therefore be dangerous. The Manufacturer will
not be responsible for any damage or loss resulting from improper
use.
3.1. USING THE GAS BURNER
To ignite the burners, place a lighted taper close to the burner, press in
and turn the control knob anti-clockwise.
If the burners have not been used for a couple of days, wait for a few
seconds before lighting the burner, this will allow any air present in the
pipes to escape.
For appliances fitted with electronic ignition carry out the following:
• Push in and turn the knob anticlockwise totheignitionsymbol.
• İgnite the burner by pressing the sparker button.
For hobs fitted with automatic ignition simply push in and turn the knob
to the ignition symbol.
The ignition system will continue to generate sparks as long as the
control knob is being pressed.
If the burner has not ignited within 5 seconds, turn the knob to the 0
position and repeat the operation.
For models fitted with a safety tap (which cuts-off the flow of gas if the
flame is accidentally extinguished) the burners are ignited and
described above, but care must be taken.
Prior to switching on the gas hob ensure that the burners and burner
caps are correctly placed within their position.
Warning: If there is no electricity on appliance, to ignite the burner a
lighter should be used;
- Push in and turn the knob anti-clockwise to the ignitionsymbol,
- While pushing in the button ignite the burner by using a lighter and
keep button pushed in 5 seconds after ignition.
GENERALADVISE
For best results, use cooking vessels with a flat surface. The size of
the surface should match the gas burner side asfollows.TableA.
4. MAINTENANCE AND CLEANING
Before cleaning the hob, ensure the appliance has cooled down.
Remove the plug from the socket or (if connected directly) switch off
the electricity supply.
Cleaning and user maintenance shall not be made by children without
supervision
Never use abrasives, corrosive detergents, bleaching agents or
acids. Avoid any acid or alkaline substances (lemon, juice, vinegar
etc.) on the enamelled, varnished or stainless steel sections.
When cleaning the enamelled, varnished or chrome sections, use
warm soapy water or a non caustic detergent. For stainless steel use
an appropriate cleaning solution.
The burners can be cleaned with soapy water. To restore their original
shine, use a household stainless steel cleaner. After cleaning, dry the
burners and replace.
It is important the Burners are replaced correctly.
Chromed grids and burners
Chromed grids and burners have a tendency to discolour with use.
This does not jeopardize the functionality of the hob.
Our After Sales Service Centre can provide spare parts if required.
For smaller containers the gas burner should be regulated so that the
flame does not overlap the base of the pan. Vessels with a concave or
convex base should not be used.
WARNING: If a flame is accidentally extinguished, turn the knob
to the off position and do not attempt to re-ignite if for at least 1
minute.
If over the years the gas taps become stiff to turn it is necessary to
lubricate them.
Such operation must be carried out only by qualified Service
Engineers.
2)Tighten the joints with the spanner, remembering to twist the
pipes into position.
3)Attach fitting C to mains gas supply using rigid copper pipe or
flexible steel pipe.
IMPORTANT: carry out a final check for leaks on the pipe
connections using a soapy solution. NEVER USE A FLAME.
Also, make sure that the flexible pipe cannot come into contact
with a moving part of the cabinet (eg.adrawer) and that it is not
situated where it could be damaged.
Warning: If gas can be smelt in the vicinity of this appliance turn off
the gas supply to the appliance and call the engineer directly. Do not
search for a leak with a naked flame.
Before using burner, be sure, grid perimeters center the burner as
below figure.
If you are using Cast Iron Grids; underneath the grid, position of it is
stated. Be sure for the exact grid is usedincorrect position.

Chat with your Candy CHW6LBX manual using AI

Get instant AI answers from your Candy CHW6LBX manual

Ask anything about the Candy CHW6LBX. Answers come from this manual, with the pages they are based on.

CHW6LBX Maintenance Schedule

After every use
Clean the hob surface

Clean the hob after every use to prevent build-up of dirt and grease. Ensure appliance is cooled down before cleaning.

As needed
Lubricate stiff gas taps

If gas taps become stiff over the years, they must be lubricated by a qualified Service Engineer only.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend CHW6LBX?

Yes No

Frequently Asked Questions

A

No, installation must be performed by a professionally qualified person to ensure safety and compliance with local regulations. Improper installation can void warranties and pose serious risks.

Is this answer helpful?

A

If the model has a safety tap, the gas flow will automatically cut off. You must turn the knob to the off position and wait at least one minute before attempting to re-light the burner.

Is this answer helpful?

A

You need to remove the injectors and replace them with ones suitable for the new gas type (natural gas or LPG) using a 7mm spanner. Always replace the rating plate after adjustment.

Is this answer helpful?

A

No, unattended cooking with fat or oil is dangerous and can cause fires. Short-term cooking processes must be supervised continuously.

Is this answer helpful?

A

Never place aluminum foil or plastic pans on the heating zones. They can melt or catch fire, creating a hazard.

Is this answer helpful?

A

The cooktop should be cleaned after every use to prevent dirt and grease buildup. Burners can be washed with soapy water and dried thoroughly before replacement.

Is this answer helpful?

A

The distance between the hob and any side cabinet must be at least 15 cm, and the distance to the rear wall must be at least 70 mm.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Three versatile burner types including auxiliary, semi-rapid, and rapid for all cooking needs
  • Built-in safety features like flame failure protection and clear warnings against misuse
  • Compatible with both natural gas and LPG with easy adjustment instructions
  • Standard dimensions fit most 60cm kitchen cutouts easily
  • Durable construction with enamel and chrome surfaces for long-term use
VS

Disadvantages

  • Requires professional installation for gas and electrical connections
  • Chromed parts may discolor over time with heavy usage
  • Strict ventilation requirements must be met for safe operation
  • Cannot be operated with external timers or remote control systems
  • Cleaning requires specific non-abrasive products to avoid surface damage
M: QW-35-FL

Product Specification

Power

7.2 kW

Design

stainless steel

Width

23.62 in (standard width)

Cooking Zones

4 cooking zones, including 1x high-power burner (2.5 kW), 2x standard burners (1.7 kW), 1x eco-burner (1 kW)

Temperature Control

continuous

Control

rotary selector (side-mounted)

Features

ignition system

M: QW-35-FL

Product Description

Candy CHW6LBX Gas Cooktop Autonomous: Elevate Your Kitchen Experience

The Candy CHW6LBX Gas Cooktop Autonomous represents a perfect blend of traditional cooking performance and modern safety features. Designed for the domestic kitchen, this appliance offers versatile cooking options with its three distinct burner types: an auxiliary burner for gentle simmering, a semi-rapid burner for everyday tasks, and a rapid burner for quick boiling. The sleek design fits seamlessly into standard worktops, provided they are heat-resistant up to 100°C and have a thickness between 25 and 45 mm.

Safety is paramount in the design of this cooktop. It includes robust warnings against unattended cooking with oil or fat, which can lead to dangerous fires. The unit ensures that children under eight years old remain safe by requiring supervision if they are near the appliance. Furthermore, the cooktop prevents accidents by warning users never to use water on a grease fire; instead, one should switch off the unit and smother the flames with a lid or fire blanket. The surface becomes hot during operation, so care must be taken to avoid touching heating elements until they cool down completely.

Installation requires professional attention to ensure compliance with national regulations. The gas connection must be secure, using appropriate regulators and pipes that do not exceed two meters in length. Electrical connections must be earthed correctly with a yellow-green wire, and the plug must be accessible. For optimal performance, the cooktop needs adequate ventilation, ideally through an extractor hood that changes the air three to five times per hour. If no hood is installed, an electric fan must be used to maintain air quality.

Maintenance is straightforward but requires specific care. Users should clean the cooktop after every use to prevent grease buildup, which can cause smoke and unpleasant odors. Only warm soapy water or non-caustic detergents should be used on enamel or chrome sections. Abrasive cleaners, acids, and high-pressure sprays are strictly prohibited as they can damage the surface. Burners and grids may discolor over time due to normal use, but this does not affect functionality. If the gas taps become stiff, they require lubrication by a qualified service engineer.

Important Notes

  • Always place pans in the center of the burner to ensure even heating.
  • Do not use the cooktop as a cutting board or storage area.
  • Ensure the flame does not extend beyond the base of small pots.
  • Check for gas leaks using a soapy solution, never an open flame.
  • Replace the rating plate after adjusting the gas type settings.
M: QW-35-FL

© Copyright 2026 Manual.ly