Manual.ly Logo

Burris FastFire II Manual

0.0 · 0 Ratings

PDF manual · 8 Pages

English

M: qwen/qwen3.8-flash
page

/ 8

Loading...
burris-fastfire-ii-red-dot-sight-user-guide-32986f1b-bae9-4250-aa54-ef70f5fc7db5 page 7
One scale division of this disc (or tick
mark) corresponds to 1 minute of
angle (MOA), or approximately 1 inch
at 100 yards. For other distances, this
value is proportional, for example: .5
inch at 50 yards or 0.1 inch at 10 yards.
Before shooting, make sure to tighten
the lock screws on the rear of the
FastFire 2 with the provided screwdriver,
making sure not to over-tighten.
Integrated Control Electronics
The integrated control circuit adjusts the brightness of the aiming
dot according to surrounding light levels.
The brightness sensor on the front of the sight senses the light level
in the direction of the target and modifies the intensity of the dot
accordingly so that it is not overpowering in low light while remaining
highly visible in bright daylight.
Be careful not to obstruct the sensor. Clean if necessary. Covering the
sensor with your finger will affect the electronics only slightly. If you
wish to check its function, cover the sensor with the protective cover.
To ensure immediate functionality, the light-emitting diode remains
on even in complete darkness but uses such a small amount of energy
that you can expect a service life of up to 4 years.
Ambient Conditions
The FastFire 2 is water-resistant and is usable even after being
accidentally submerged. However, after exposure to salty or dirty
water, it is advisable to rinse with distilled water and dry the sight,
as with any quality optical equipment.
6
FastFire 2 User Guide_Layout 1 8/24/15 1:13 PM Page 7

Chat with your Burris FastFire II manual using AI

Get instant AI answers from your Burris FastFire II manual

Ask anything about the Burris FastFire II. Answers come from this manual, with the pages they are based on.

FastFire II Maintenance Schedule

As needed
Clean optical surfaces and lens

Remove dirt by blowing it off or using a very soft lens brush. Use lens cleaning tissues on the optical surfaces.

As needed
Rinse after salt/dirty water exposure

After exposure to salty or dirty water, rinse with distilled water and dry the sight.

As needed
Clean battery contact surface

Keep the contact surface clean, cleaning with alcohol if necessary during battery installation or replacement.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend FastFire II?

Yes No

Frequently Asked Questions

A

The FastFire II operates using a single 3V Lithium battery, specifically the CR2032 model. It is important not to substitute this with two CR2016 batteries as they will not fit or function correctly. To install or replace the battery, turn the sight upside down and insert the new battery so that the positive pole label is visible. A magnet inside the housing draws the battery onto the contact plate. Ensure the contact surface is clean, using alcohol if necessary, to maintain optimal electrical connection and consistent performance.

Is this answer helpful?

A

To adjust windage and elevation, first loosen the two lock screws located on the rear of the sight using the provided screwdriver. Turn the slotted UP or LEFT screws with the adjusting scale disc and screwdriver. Each click represents one minute of angle (MOA). After making adjustments, remember to tighten the lock screws securely but avoid over-tightening to prevent damage. The scale disc helps track exact movement amounts for precise zeroing of your point of impact.

Is this answer helpful?

A

The FastFire II is designed to be water-resistant and remains functional even after accidental submersion. However, it is not fully waterproof for prolonged diving activities. If the sight is exposed to salty or dirty water, it is advisable to rinse it thoroughly with distilled water and dry it completely afterward. This maintenance step protects the optical surfaces and internal electronics from corrosion and ensures long-term reliability and clarity of the aiming dot.

Is this answer helpful?

A

While the FastFire II is versatile, installation on most handguns requires specific mounting plates depending on the model. The base package includes a Weaver/Picatinny-style mount suitable for many platforms. For other firearms like Glock, Sig Sauer, or Beretta models, separate mounting plates such as the 410326 or 410327 are needed. Always check compatibility charts to ensure you have the correct hardware for secure and proper alignment of the optic on your specific firearm platform.

Is this answer helpful?

A

Burris backs the FastFire II with their Forever Warranty. This comprehensive coverage means Burris will repair or replace your optic if it is damaged or defective, regardless of who owns it. There are no questions asked, no receipt required, and no warranty card needed. The warranty automatically transfers to future owners, reflecting confidence in the craftsmanship and durability of the product. You can count on Burris to support your investment throughout the lifetime of the optic.

Is this answer helpful?

M: qwen/qwen3.8-flash

Advantages and Disadvantages

Advantages

  • Compact and lightweight design weighing less than one ounce preserves firearm balance
  • Automatic brightness adjustment optimizes dot visibility for varying environmental light levels
  • Both-eyes-open shooting capability enhances situational awareness and target acquisition speed
  • Durable construction from stainless steel and anodized aluminum resists heavy recoil impact
  • Simple installation process with included Picatinny/Weaver mount and necessary tools
VS

Disadvantages

  • Requires specific mounting plates for certain handgun models not included in base package
  • Battery compartment access requires turning the unit upside down which may be inconvenient
  • Windage and elevation adjustments need loosening lock screws before every zeroing session
  • Limited sight window size compared to larger tube-style optics might restrict peripheral view
  • No manual brightness override option available for users preferring fixed intensity settings
M: qwen/qwen3.8-flash

Product Description

Burris FastFire II Red Dot Sight (User Guide) - Read, Download & Print Free

Overview of the FastFire II Experience

The Burris FastFire II stands as a premier choice for shooters seeking speed and precision in their aiming solutions. This red dot reflex sight is engineered to enhance performance across handguns, rifles, and shotguns without adding unnecessary bulk or weight. With a design that prioritizes both-eyes-open shooting, it allows users to maintain situational awareness while acquiring targets rapidly. The compact frame ensures that firearm balance remains unaffected, making it an ideal upgrade for competitive shooters and tactical enthusiasts alike.

Key Features and Performance

One of the standout characteristics of the FastFire II is its automatic brightness adjustment technology. This feature intelligently modifies the intensity of the 4 MOA red dot based on ambient light conditions, ensuring optimal visibility whether you are shooting in dim indoor ranges or bright outdoor environments. The sight window measures 21mm x 15mm, providing a clear field of view that facilitates quick target acquisition. Additionally, the stainless steel, bronze, and anodized aluminum construction guarantees durability against heavy recoil and harsh weather conditions.

Installation and Maintenance

Setting up the FastFire II is straightforward thanks to the included Weaver/Picatinny-style mount and comprehensive package contents such as Torx screws and a protective cap. Users can fine-tune their point-of-aim using the easy-to-access windage and elevation adjustments, which offer precise control with a scale disc for accurate calibration. Regular maintenance involves simple lens cleaning and battery replacement using a standard CR2032 lithium cell, which supports a long service life due to efficient power management.

Why Choose the FastFire II?

Choosing this optic means investing in reliability and user-friendly operation. The integration of advanced electronics with mechanical robustness creates a sighting system that performs consistently under pressure. Whether you are new to optics or a seasoned expert, the intuitive controls and clear aiming dot make the learning curve minimal. Furthermore, the water-resistant build ensures functionality even after accidental submersion, highlighting its versatility in various operational scenarios.

Final Thoughts

Embrace the efficiency of modern reflex sights by integrating the Burris FastFire II into your gear setup. Its blend of lightweight design, automatic illumination, and rugged construction offers a compelling solution for enhancing your shooting accuracy and speed. Discover how this versatile optic can transform your experience at the range or in the field.

M: qwen/qwen3.8-flash

© Copyright 2026 Manual.ly