Manual.ly Logo

Britax Romer Kidfix SL Black Series Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: OA-GPT-54-NAN
page

/ 2

Loading...
b02113a6be77489a5754de0024fa1be45aaa page 2
7. SAFETY NOTES
Please take the time to read these instructions carefully and keep
them to hand in the intended storage compartment
13
on the child
safety seat at all times! The instructions must be with the child safety
seat if the latter is passed on to a third party.
DANGER! For the protection of your child:
In the event of an accident with a collision speed of more than 10 km/h,
the child safety seat may be damaged without the damage becoming
immediately visible. In this case the child safety seat must be replaced.
Please dispose of it properly.
As a rule, have your child safety seat checked if it was damaged (e.g if it
falls on the ground).
Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
Never lubricate or oil parts of the child seat.
Never leave your child unattended in the child seat in the vehicle.
Only allow your child to enter and exit the vehicle on the pavement side.
Protect the child safety seat from intensive direct sunlight when it is not in
use. The child safety seat can get very hot in direct sunshine. Child skin is
sensitive and could thereby be harmed.
The more snugly the belt ¿ts over your child's body, the better they will be pro-
tected. Therefore avoid putting thick clothes on your child under the belt.
Take regular breaks on long journeys in order to give your child the oppor-
tunity to play around.
Use on the rear seat: Move the front seat forward far enough that you
child's feet cannot hit the backrest of the front seat (to prevent risk of
injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or
objects may cause injury to other vehicle occupants. Please always check
that...
the backrests of the vehicle seats are locked (i.e. that any foldable rear
seat bench latch is engaged).
all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf)
are secured.
all persons in the vehicle have their seatbelts fastened.
the child safety seat is always secured when it is in the vehicle, even if no
child is being transported.
WARNING! For your protection when handling the child seat:
Never use the child safety seat free-standing, not even for test sitting.
:hen swivelling up the backrest
16
, nothing must come between the
backrest
16
and the seat cushion
10
. You or your child could pinch your
¿ngers, injuring them.
To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
Keep the child safety seat in a safe place when it is not in use. Do not place
any heavy objects on the seat and do not store it directly next to sources of
heat or in direct sunlight.
CAUTION! To protect your vehicle:
Certain car seat covers made from more sensitive materials (e.g. velour, leath-
er, etc.) may sustain signs of wear and tear when using child safety seats. For
optimum protection of your car seat covers, we recommend using the BRITAX
RÖMER car seat protector from our range of accessories.
PAGE II
A correctly set headrest
14
ensures that the diagonal seat belt section
18
is
optimally positioned, and gives your child optimum protection.
The headrest
14
must be adjusted so that there is a space two ¿ngers wide
between the headrest
14
and your child's shoulders.
To adMust the height of the headrest to ¿t your
child:
1. Grip the adjustment handle
15
on the back of the
headrest
14
and pull it upwards.
This unlocks the headrest.
2. You can now move the unlocked headrest
14
to
the desired height. As soon as you release the
adjustment handle
15
, the headrest
14
will lock
into place.
3. Place the child safety seat on the vehicle seat.
4. Have your child sit down in the child safety seat and
check the height. Repeat the procedure until the
headrest
14
has the correct height.
8. ADJUSTING THE HEADREST &
SECURING THE SICT
9. INSTALLATION
With ISOFIT + 3-point belt
A
10. SECURING YOUR CHILD
14
15
14
With 3-point belt
B
7. Push both ISOFIT locking arms
07
into the insertion
aids
02
until the ISOFIT locking arm
07
engages
with a clicking sound.
DANGER! Check that the ISOFIT locking arm is
correctly engaged
07
by pulling on it.
9. Press the red ISOFIT locking button
08
to ensure
that the hook on the ISOFIT locking arm
07
is open
and ready for use.
10. Push both ISOFIT locking arms
07
into the
insertion aids
02
until the ISOFIT locking arm
07
engages with a clicking sound.
DANGER! Check that the ISOFIT locking arm is
correctly engaged
07
by pulling on it.
11. Pull on the adjustment belt
12
and push the
child seat backwards at the same time, until the
die backrest
16
is Àush with the backrest of the
vehicle seat.
12. Give the child safety seat a ¿rm pull forwards to
ensure that it is securely fastened and check the
ISOFIT locking arms again
07
to ensure that both
are fully locked in place.
13. Carry out the steps in Section 10 „SECURING
YOUR CHILD“.
For the safety of your child, before every journey in the car check
that...
Źthe child safety seat is slotted in on both sides with the ISOFIT locking
arms
07
in the ISOFIT fastening points
01
;
Ź the child safety seat is securely fastened;
Źthe lap belt
17
runs in the bright red belt guides on both sides of the seat
cushion
06
,
Źthe diagonal seat belt section
18
on the side of the vehicle seatbelt buck-
le
19
also runs through the light red belt guide
06
of the seat cushion,
Źthe diagonal seat belt section
18
runs through the dark red belt holder
09
of the headrest,
Źthe SICT
03
isinstalled and used correctly,
Źthe diagonal seat belt section
18
runs diagonally backward,
Źthe straps are tight and not twisted,
ŹThe seatbelt buckle
19
must not be positioned on the red belt guide
06
in
the seat cushion.
DANGER! If your child tries to open
the red ISOFIT safety button
08
or the vehicle belt buckle
19
, stop the vehicle as soon as safely possible.
Check whether the child safety seat is correctly fastened and ensure that
your child is correctly secured. Explain to your child the dangers associated
with his actions.
01
02
1. If your vehicle is not ¿tted with ISOFIX insertion aids as standard, clamp
the two insertion aids
02
which are supplied with the seat* to the upward
pointing part of the two ISOFIX fastening points
01
of your vehicle.
TIP!
The ISOFIX fastening points are located between the surface and the back-
rest of the vehicle seat.
* The insertion aids facilitate the installation of the child safety seat with the use of the
SOFIX fastening points and prevent damage to the car seat covers. As long as they
are not used, remove them and keep them in a safe place. For vehicles with foldable
a backrest, the insertion aids need to be removed before folding the backrest. Any
problems occurring usually come from soiling or external objects on the insertion aids
and on the hook. Remove soiling or external objects to rectify such problems.
2. Moving the headrest of the vehicle seat into the top position.
3. Carry out the steps in Section 8 "ADJUSTING THE HEADREST & SE-
CURING THE SICT“.
The
KIDFIX SL / KIDFIX SL SICT
is installed permanently in the vehicle with the
ISOFIT locking arms.
Your child is then buckled into the child seat with the vehicle's 3-point seatbelt.
4. Place the child seat facing forward (in the direction
of travel) on a suitable vehicle seat.
5. Hold the ISOFIT
adjustment button
11
down and
fully extend the ISOFIT locking arm furthest from
the vehicle door
07
.
6. Press the red ISOFIT locking button
08
to ensure
that the hook on the ISOFIT locking arm
07
is open
and ready for use.
11
07
0807
16
12
8. Hold the ISOFIT adjustment button
11
down and
fully extend the ISOFIT locking arm nearest to the
vehicle door
07
.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the steps
in Section 6 „REMOVAL“ [PAGE I]
07
07
11
0807
07
1. Carry out the steps in Section 8 "ADJUSTING
THE HEADREST & SECURING THE SICT“.
2. Place the child seat on the vehicle seat. Ensure
that the backrest
16
is Àush with the backrest of
the vehicle seat.
Tip! If the headrest of the vehicle seat gets in the
way, turn it the other way.
3. Carry out the steps in Section 10 „SECURING
YOUR CHILD“.
For the safety of your child, before every journey in the car check
that...
Źthe child safety seat is securely fastened;
Źthe lap belt
17
runs in the bright red belt guides on both sides of the seat
cushion
06
,
Źthe diagonal seat belt section
18
on the side of the vehicle seatbelt buck-
le
19
also runs through the light red belt guide
06
of the seat cushion,
Źthe diagonal seat belt section
18
runs through the dark red belt holder
09
of the headrest,
Źthe diagonal seat belt section
18
runs diagonally backward,
Źthe straps are tight and not twisted,
Źthe SICT
03
is installed and used correctly,
Źthe seatbelt buckle
19
must not be positioned on the red belt guide
06
in
the seat cushion.
DANGER! If your child tries to open the vehicle belt buckle
19
, stop the
vehicle as soon as safely possible. Check whether the child safety seat is
correctly fastened and ensure that your child is correctly secured. Explain
to your child the dangers associated with his actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the
steps in Section 6 „REMOVAL“ [PAGE I]
16
The
KIDFIX SL / KIDFIX SL SICT
is not installed permanently in the vehicle. It
is simply secured together with your child using the vehicle's 3-point seatbelt.
KIDFIX SL SICT & KIDFIX SL:
1. Have your child sit down in the child seat.
2. Pull out the vehicle belt and guide it in front of your
child to the vehicle seat buckle
19
.
DANGER! Ensure the vehicle belt is not twisted, as
otherwise the full protective effect of the
retaining system is not ensured.
3. Engage the buckle tongue in the vehicle seat buck-
le
19
with a CLICK!
4. Place the diagonal seat belt section
18
and lap
belt section
17
on the side of the vehicle seatbelt
buckle
19
into the light red belt guide
06
of the seat
cushion.
DANGER! The vehicle seatbelt buckle
19
must
not be positioned between the light red
belt guide
06
and the armrest.
5. Also place the lap belt section
17
on the other side
of the seat cushion in the light red belt guide
06
.
DANGER! The lap belt section
17
must lie as low
as possible over your child's hips on
both sides.
6. Guide the diagonal seat belt section
18
into the dark
red belt holder
09
of the headrest
14
until it lies
completely in the belt holder
09
and is not twisted.
Tip! If the backrest
16
conceals the belt holder
09
,
you can adjust the headrest
14
upwards. The diagonal
seat belt section
18
can now be easily inserted. Now
return the headrest
14
to the proper height.
7. Make sure that the diagonal belt
18
runs over your
child's shoulder, and not in front of his or her neck.
Tip! You can still adjust the height of the headrest
14
again here in the vehicle.
DANGER! The diagonal seat belt section
18
must
run diagonally backward. You can
adjust the course of the belt with your
vehicle's adjustable belt deÀector.
DANGER! The diagonal belt
18
must never be di-
rected forwards to the belt deÀector on
the vehicle. In this case, use the child
safety seat on the back seat only.
8. Tighten the vehicle seat belt by pulling on the diag-
onal seat belt section
18
.
9. Observe the further steps of the relevant instal-
lation type.
19
18
17
06
19
17
06
18
18
18
09
14
19
ONLY KIDFIX SL SICT:
Press the SICT
03
into both SICT fastening points on
the side of the child seat nearest the vehicle door
05
and clip in the SICT
03
.
CAUTION! Make sure that there is a gap of ap-
proximately 5 mm between the SICT
and the vehicle door in order to avoid
pressure marks and other damage to
the door trim.
03
05
How to secure the SICT:
BRITAX RÖMER
Kindersicherheit GmbH
Blaubeurer Straße 71
D-89077 Ulm
Germany
T.: +49 (0) 731 9345-199/-299
F.: +49 (0) 731 9345-210
www.britax.eu
BRITAX EXCELSIOR
LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.:
www.britax.eu
If you have any further questions regarding its use, please feel free to
contact us:
16
14
150415_KIDFIX_SL_KIDFIX_SL_SICT_GB.indd 2 15.04.2015 08:23:32

Chat with your Britax Romer Kidfix SL Black Series manual using AI

Get instant AI answers from your Britax Romer Kidfix SL Black Series manual

Ask anything about the Britax Romer Kidfix SL Black Series. Answers come from this manual, with the pages they are based on.

Kidfix SL Black Series Maintenance Schedule

Remind me when maintenance is due
Monthly
Check all parts for damage

Regularly inspect all important parts for damage. Ensure all mechanical components function perfectly.

Before every trip
Verify installation and harness

Before each drive, check that the seat is securely attached, belts are routed correctly, and not twisted or loose.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Kidfix SL Black Series?

Yes No

Frequently Asked Questions

A

It is designed for children weighing 15 to 36 kg, which usually corresponds to about 4 to 12 years of age. It belongs to group II and III child seats and is intended for the later stage of child restraint use.

Is this answer helpful?

A

Yes. The seat can be installed using ISOFIX anchoring points where the vehicle supports them. The locking arms help secure the seat more firmly, and the manual stresses checking that both sides click into place correctly.

Is this answer helpful?

A

Yes. It can also be secured with the vehicle’s 3-point seat belt. In that setup, the child is buckled into the seat using the car belt, following the red belt guides on the seat cushion and headrest.

Is this answer helpful?

A

The lap belt should sit low over the hips and pass through the bright red guides on both sides of the seat cushion. The diagonal belt should run through the dark red guide on the headrest and across the shoulder, not the neck.

Is this answer helpful?

A

Yes. The headrest can be moved up or down to match the child’s height. This helps the seat fit properly and supports correct belt positioning as the child grows.

Is this answer helpful?

A

Yes. The cover can be removed and washed with a mild detergent on a delicate cycle at 30°C. The plastic parts can be cleaned with soapy water, but harsh cleaners should be avoided.

Is this answer helpful?

A

If the seat has been involved in a collision, it should be checked and may need to be replaced even if no damage is visible. The instructions warn that impact damage can exist without obvious signs, so safety should come first.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Supports children from 15 to 36 kg, making it suitable across several growth stages.
  • Can be installed with ISOFIX or a 3-point seat belt for added flexibility.
  • Color-coded belt guides help route the seat belt correctly and reduce mistakes.
  • Adjustable headrest improves fit and helps position the diagonal belt properly.
  • Removable, washable cover makes day-to-day cleaning easier for families.
VS

Disadvantages

  • Must be used carefully to ensure the belt is routed exactly as instructed.
  • Not suitable for younger children or for use with a 2-point belt.
  • Requires vehicle compatibility checking before installation.
  • After any crash, the seat may need replacement even if damage is not visible.
M: OA-GPT-54-NAN

Product Specification

Group

2/3

Weight class

33.07-79.37lbs

Age class

4-12Y

Color

blue, black

Belt system

Three-point safety harness

Installation

forward-facing

Isofix

no, Isofit connectors

Features

height- and width-adjustable backrest, height-adjustable headrest and shoulder straps, side impact protection, removable/washable cover

Dimensions (WxHxD)

20.08x26.38-33.46x14.96in

Weight

14.11lbs

M: OA-GPT-54-NAN

Product Description

Britax Römer Kidfix SL Black Series Moonlight Blue 2018/2019

The Britax Römer Kidfix SL Black Series moonlight blue 2018/2019 Manual reflects a child seat designed for everyday reliability, comfort, and straightforward use. Built for children in the 15–36 kg range, it supports the transition through group II and III stages, typically covering roughly 4 to 12 years of age. Its main purpose is simple: to help position the vehicle belt correctly while giving young passengers a stable, protective seating solution.

One of the standout features is the flexible installation approach. The seat can be used with ISOFIX anchoring points or secured with the vehicle’s 3-point seat belt, depending on the car and setup. This makes it a practical option for families who move the seat between vehicles or want a more secure fitted installation when ISOFIX is available. The bright red and dark red belt guides are easy to follow, helping the lap and diagonal sections of the belt sit in the right places.

Comfort and fit are also central to the design. The adjustable headrest helps the seat grow with the child, while supporting the correct routing of the shoulder belt. A properly set headrest is important not only for comfort, but also for safety, since it helps keep the diagonal belt positioned across the shoulder rather than the neck. The seat is built to stay forward-facing, in line with its approved use and weight class.

The product also emphasizes easy maintenance. The cover can be removed and washed gently, and the plastic parts can be cleaned with mild soapy water. That matters in daily family use, where crumbs, spills, and busy routines are part of life. For added protection, some versions include SICT side impact technology, offering another layer of reassurance near the vehicle door.

Notes

  • Always check your vehicle compatibility before installation.
  • The seat must be used with the correct belt routing at all times.
  • After an accident, even if damage is not visible, the seat should be replaced.
  • Keep the manual stored with the seat for future reference.

In short, this Britax Römer model is a practical, well-guided child seat for parents who want trusted safety features, clear installation steps, and everyday usability in one compact solution.

M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly