Manual.ly Logo

Bosch DIY UniversalChain 18 Manual

4.0 · 2 Ratings

PDF manual · 407 Pages

English

M: OA-GPT-54-NAN
page

/ 407

Loading...
a481945a0b3af3c234a050be7a40cb106152 page 16
22 | English
F 016 L81 719 | (21.12.17) Bosch Power Tools
Tensioning the Saw Chain (seefigure C)
Always check the chain tension before use, after the first cuts
and regularly during use approx. every 10 minutes. Upon
initial operation, new chains can lengthen considerably.
The chain life of the saw chain mainly depends upon sufficient
lubrication and correct tensioning.
Avoid tensioning the chain if it is hot, as this will cause the
chain to become overtensioned and face too tightly against
the chain bar when it cools down.
– Place the chain saw on any suitable flat surface.
–Turn clamping knob 14 approx. 1 – 3 turns anticlockwise
to loosen the chain bar.
– Check if the chain links are correctly located in the slot
around the chain bar 11 and on the drive sprocket 20.
– Turn the red chain-tensioning ring 13 clockwise ratcheting
until the correct chain tension is reached. The ratchet
mechanism prevents the chain tension from loosening. If
the chain-tensioning ring 13 is hard to turn, loosen the
clamping knob 14 further in anticlockwise direction. The
locking knob 14 may also turn, when adjusting the chain-
tensioning ring 13.
–The saw chain 12 is correctly tensioned when it can be
raised approx. 5–10 mm from the chain bar in the centre.
This should be done by using one hand to raise the saw
chain against the weight of the machine.
–If the saw chain 12 is overtensioned, turn the chain-
tensioning ring 13 in anticlockwise direction.
–When the saw chain 12 is tensioned, clamp the chain bar
11 by turning the locking knob 14 in clockwise direction.
Do not use a tool for this.
Saw-chain Lubrication (see figure D)
Note: The chain saw is not supplied filled with oil (delivery
scope). It is essential to fill with oil before use. Operating the
chain saw without chain oil or when the oil level is below the
minimum mark will result in damage to the chain saw.
Chain life and cutting capacity depend on optimum
lubrication. Therefore, the chain is automatically lubricated
with chain oil during operation via the oil outlet 21.
Filling the oil reservoir:
– Set chain saw on any suitable surface with the oil filler cap
4 facing upward.
– Clean area around the oil filler cap 4 with a cloth and
unscrew the cap.
– Add Bosch biodegradable chain saw oil until oil level reads
“max” on oil level gauge 7.
– Avoid dirt or debris from entering the oil reservoir. Screw
on oil filler cap 4 again and tighten.
– Run chainsaw for 30 seconds to “prime” oil system.
Note: To allow venting of the oil reservoir, small breather
channels are provided between the oil filler cap. To prevent
leakage ensure chain saw is left in a horizontal position (oil
filler cap 4 uppermost) when not in use.
Note: It is important to use only readily biodegradable chain
lubricants (according to RAL-UZ 48) to avoid damage to the
chain saw. Never use recycled/old oil. Use of non approved oil
will invalidate the warranty.
Note: Oil becomes denser at lower temperatures which
decreases the flow rate of oil.
Operation
Inserting the battery
Insert the charged battery 17. Ensure that the battery is
inserted correctly.
Switching On and Off
Hold the chain saw as described in section “Working with the
Chain Saw”.
To start the machine, first push the lock-off button for the
On/Off switch 3 and then press the On/Off switch 2 and keep
it pressed.
When the machine is running, the lock-off button can be
released again.
To switch off the machine, release the On/Off switch 2.
Note: For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
Working with the Chain Saw
Before Cutting
Before starting operation and periodically during cutting,
carry out the following checks:
– Is the chain saw in a safe condition?
– Is the oil reservoir filled? Check oil level gauge prior to
starting and regularly during operation. Refill oil when oil
level has reached the bottom edge of the viewing glass.
The oil tank filling will last approx. 15 minutes, depending
on sawing intensity and stops.
– Is the saw chain properly tensioned and sharp? Check
chain tension every 10 minutes during operation. Upon
initial operation, new chains can lengthen considerably.
The condition of the chain influences the cutting
performance. Only a sharp chain protects from overload.
– Are you wearing the required protective equipment? Wear
safety glasses and hearing protection. Further protective
equipment for head, hands, legs and feet is
recommended. Suitable protective clothing reduces the
danger of injury from thrown about cutting material and
accidental touching of the saw chain.
Kickback
Do not remove or modify the tip protector! Tool is fitted
with a tip protector to help protect against effect of kick back
by accidentally touching the tip of the tool against the wood.
Kickback is the sudden backward/upward motion of the chain
saw, occuring when the chain (at the tip of the chain bar)
OBJ_BUCH-3472-001.book Page 22 Thursday, December 21, 2017 4:11 PM

Chat with your Bosch DIY UniversalChain 18 manual using AI

Get instant AI answers from your Bosch DIY UniversalChain 18 manual

Ask anything about the Bosch DIY UniversalChain 18. Answers come from this manual, with the pages they are based on.

UniversalChain 18 Maintenance Schedule

Every 10 minutes
Check saw chain tension

Always check the chain tension before use, after the first cuts and regularly during use approx. every 10 minutes.

Show in the manual (page 22)
After 1-3 hours of use
Clean cover, bar and chain

Remove the cover, chain bar and saw chain, and clean them using a brush to remove sawdust and debris from oil pipes.

Show in the manual (page 25)
Before storage
Empty oil reservoir

Remove the oil from the reservoir before storage to prevent leaks or damage.

Show in the manual (page 25)
As needed
Clean plastic housing

Clean the moulded plastic housing using a soft brush and clean cloth; do not use water, solvents or polishes.

Show in the manual (page 25)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend UniversalChain 18?

Yes No
0
User Pic

sunt_itaque

8 months ago

Is the effective cutting length reduced because the safety guard at the tip is riveted on, and will the saw handle thicker branches with enough oiling?

0
User Pic

Manual.ly

8 months ago

Yes. The tip protection bar is permanently fixed for safety, so the usable cutting length is shorter than the full bar length stated. This model is designed for small trees, shrubs, and thinner branches, not for cutting thicker limbs. For oiling, the saw uses automatic chain lubrication, but it is set for normal intermittent use. Make sure you use the recommended bar and chain oil, keep the oil reservoir filled, and check the oil flow before work. If you need prolonged, heavy-duty cutting, consider a more powerful saw with a longer bar and a larger lubrication system.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It is best for everyday garden tasks such as cutting branches, trimming small logs, clearing fallen wood, and handling light pruning jobs. It is designed for wood only and works well for DIY maintenance.

Is this answer helpful?

A

Yes, this version includes a 2.5Ah battery. That makes it more convenient for users who want a ready-to-use cordless setup without buying the battery separately.

Is this answer helpful?

A

No. The saw uses a tool-less chain tensioning system, so you can adjust the chain quickly by hand. This is useful during regular maintenance or after a few cuts, when the chain may loosen slightly.

Is this answer helpful?

A

Yes. The chain must be filled with suitable chain oil before use, and the oil level should be checked regularly. Automatic lubrication helps keep cutting smooth and reduces wear.

Is this answer helpful?

A

It includes KickBack Control, a run-down brake, and a tip protector. The manual also recommends two-handed operation, eye and hearing protection, and keeping a secure stance while cutting.

Is this answer helpful?

A

It can handle logs and branches within its 135 mm cutting capacity, but it is not intended for heavy forestry work or very large trunks. It is better suited to light and medium garden cutting tasks.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Cordless 18V design gives freedom of movement for garden cutting without a power cable.
  • Tool-less SDS chain tensioning makes quick adjustments simple and convenient.
  • Automatic chain lubrication supports smoother cutting and helps protect the chain.
  • KickBack Control and tip protector improve safety and user confidence.
VS

Disadvantages

  • 20 cm bar and 135 mm cutting capacity are best for light to medium tasks, not heavy felling.
  • Regular oiling and chain checks are needed to keep performance at its best.
  • At about 3.0 kg, it may feel tiring during longer overhead or extended use.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

1x Battery (18V, 2.5Ah, Li-Ion)

Bar length

7.87 in

Chain speed

14.76ft/s

Chain pitch

3/8"

Chain oil tank

2.71 fl oz

Features

Charge status indicator, Softgrip, Auxiliary handle, Tool-free chain tensioning, Tool-free chain change, Automatic chain lubrication, Chain brake, Spike bumper

Vibration level

12.14ft/s^2

Charging time

1h

Noise level

95dB(A)

Weight

6.61lb (incl. battery)

Scope of delivery

Charger (AL1830CV), 1x Battery, Bar cover

M: OA-GPT-54-NAN

Product Description

Bosch DIY UniversalChain 18 Cordless Chainsaw incl. Battery 2.5Ah Manual

A compact cordless saw for everyday garden work

The Bosch DIY UniversalChain 18 is built for homeowners who want a practical, easy-to-handle chainsaw for regular outdoor tasks. As a cordless 18V tool, it gives you the freedom to move around the garden without dragging a cable behind you. That makes it especially useful for trimming branches, cutting firewood, tidying fallen limbs, and handling light pruning jobs where mobility matters.

What makes the Bosch DIY UniversalChain 18 Cordless Chainsaw incl. Battery 2.5Ah Manual appealing is its balanced mix of convenience and control. The 20 cm guide bar and 135 mm cutting capacity are well suited to smaller logs and branches, while the automatic chain lubrication helps maintain smoother cutting performance. The tool-less SDS chain tensioning system is another welcome detail, because it allows quick adjustments without extra tools, saving time when you are in the middle of a job.

Designed with safety and usability in mind

Bosch has clearly focused on making this saw approachable for DIY users. KickBack Control and the tip protector help reduce the chance of sudden backward movement, which is important when cutting wood at awkward angles. The run-down brake, front and rear grips, and clear battery status indication also support safer, more predictable operation. The manual stresses two-handed use, proper stance, and regular chain checks, all of which reinforce the saw’s practical, safety-first design.

The included 2.5Ah battery adds real value for casual users who want to get started right away. It offers a good balance between runtime and weight, making the saw easier to carry than larger, heavier garden equipment. At around 3 kg, the tool remains fairly manageable for short to medium sessions, especially when working close to the ground or cutting logs on a stable surface.

A good fit for routine garden maintenance

This model is best viewed as a dependable helper for routine cutting rather than a full-scale forestry machine. It is made for wood only, and it performs best when the chain is sharp, correctly tensioned, and properly lubricated. For pruning, branch clearing, and general maintenance, it offers the kind of straightforward functionality many DIY users want: simple setup, cordless freedom, and enough power for common garden tasks.

Notes

  • Check chain tension regularly, especially when the saw is new.
  • Use only suitable chain oil and keep the oil tank filled.
  • Follow the manual carefully for safe handling and maintenance.
  • Ideal for wood cutting, not for masonry, plastic, or other non-wood materials.
  • Best suited to light and medium garden jobs rather than heavy-duty felling.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly