Manual.ly Logo

Bosch DIY PTK 14 EDT Manual

5.0 · 5 Ratings

PDF manual · 68 Pages

English

M: OA-GPT-5-NAN
page

/ 68

Loading...
b8c9ee99598077580319b895c9fe287dff10 page 8
8 | Deutsch
1 609 92A 1XJ | (19.11.15) Bosch Power Tools
DuoTac-Automatik
Mit der DuoTac-Automatik werden 2 Klammern gleichzeitig
verarbeitet. Durch die doppelte Klammerndicke wird die
Reißfestigkeit von dünnen Materialien, z. B. Stoffen oder Foli-
en, erhöht.
Bei der Verarbeitung von Nägeln ist die DuoTac-Funktion
nicht möglich.
– Schieben Sie den Umschalter für die DuoTac-Automatik 2
nach oben, um 2 Klammern gleichzeitig zu verarbeiten.
Schieben Sie den Umschalter für die DuoTac-Automatik 2
nach unten, um eine Klammer oder einen Nagel zu verar-
beiten.
Schlagkraftvorwahl
Mit dem Stellrad 5 für die Schlagkraftvorwahl können Sie die
benötigte Schlagkraft in Stufen vorwählen.
Die erforderliche Schlagkraft ist von der Länge der Klammern
bzw. Nägel und der Festigkeit des Materials abhängig.
Bei der Verarbeitung von 2 Klammern (DuoTac-Funktion)
muss am Stellrad 5 für die Schlagkraftvorwahl ca. eine Stufe
höher gewählt werden.
Hinweis: Probieren Sie die eingestellte Schlagkraft immer zu-
erst an einem Materialrest aus. Die optimale Schlagkraftein-
stellung lässt sich nur durch praktische Versuche ermitteln.
Die Angaben in der nachfolgenden Tabelle sind empfohlene
Werte.
Einstellbereich Stellrad 5
Arbeitshinweise
Mit diesem Elektrowerkzeug können keine 19 mm-
Klammern verarbeitet werden. Benutzen Sie deshalb
das Elektrowerkzeug nicht zur Befestigung von De-
ckenverkleidungen mit Profilholz- oder Fugenkrallen.
Vermeiden Sie Leerschüsse, um den Verschleiß des Schlag-
stempels zu vermindern. Stellen Sie nach Abschluss der Ar-
beiten die Schlagkraft am Stellrad Schlagkraftvorwahl 5 auf
einen niedrigen Wert, um die Spannfeder zu entlasten.
Das Elektrowerkzeug ist für den Kurzzeitbetrieb ausgelegt
und erwärmt sich bei Dauerbetrieb. Mit zunehmender Erwär-
mung verringert sich die Leistung. Die Betriebsart S2 be-
zeichnet den Kurzzeitbetrieb mit einer maximalen Betriebs-
dauer von 10 min. unter konstanter Belastung. Stellen Sie
nach dieser Zeit das Elektrowerkzeug ab und lassen Sie es ab-
kühlen.
Entfernen verklemmter Klammern
Ziehen Sie vor allen Arbeiten am Elektrowerkzeug den
Netzstecker aus der Steckdose.
– Drehen Sie das Elektrowerkzeug um.
– Drücken Sie die Entriegelung 6 und ziehen Sie dabei das
Magazin 9 nach hinten heraus.
– Entfernen Sie die verklemmte Klammer. Verwenden Sie
dazu bei Bedarf eine Zange.
– Schieben Sie das Magazin 9 zurück, bis es einrastet.
Bestücken Sie das Magazin rechtzeitig. Ein zu kurzer
Klammerstreifen kann die Ursache für verklemmte Klam-
mern sein.
Wartung und Service
Wartung und Reinigung
Ziehen Sie vor allen Arbeiten am Elektrowerkzeug den
Netzstecker aus der Steckdose.
Halten Sie das Elektrowerkzeug und die Lüftungs-
schlitze sauber, um gut und sicher zu arbeiten.
Wenn ein Ersatz der Anschlussleitung erforderlich ist, dann
ist dies von Bosch oder einer autorisierten Kundendienststel-
le für Bosch-Elektrowerkzeuge auszuführen, um Sicherheits-
gefährdungen zu vermeiden.
Kundendienst und Anwendungsberatung
Geben Sie bei allen Rückfragen und Ersatzteilbestellungen
bitte unbedingt die 10-stellige Sachnummer laut Typenschild
des Elektrowerkzeuges an.
Der Kundendienst beantwortet Ihre Fragen zu Reparatur und
Wartung Ihres Produkts sowie zu Ersatzteilen. Explosions-
zeichnungen und Informationen zu Ersatzteilen finden Sie
auch unter:
www.bosch-pt.com
Das Bosch-Anwendungsberatungs-Team hilft Ihnen gerne bei
Fragen zu unseren Produkten und deren Zubehör.
www.bosch-do-it.de, das Internetportal für Heimwerker und
Gartenfreunde.
Untergrund
Weichholz
(Kiefer)
1–3 3
Hartholz
(Buche)
3–5 6
Spanplatten 2 –4 4
Tischlerplatte 2 –4 4
Untergrund
Weichholz
(Kiefer)
2–4
Hartholz
(Buche)
4–6
Spanplatten 4 –6
Tischlerplatte 4 –5
6
5
4
3
2
1
6 8 10 12 14 mm
14 mm
6
5
4
3
2
1
6810
12
14 mm
DuoTac
OBJ_BUCH-1439-003.book Page 8 Thursday, November 19, 2015 10:48 AM

Chat with your Bosch DIY PTK 14 EDT manual using AI

Get instant AI answers from your Bosch DIY PTK 14 EDT manual

Ask anything about the Bosch DIY PTK 14 EDT. Answers come from this manual, with the pages they are based on.

PTK 14 EDT Maintenance Schedule

After every use
Keep machine and ventilation slots clean

Clean the tool and ventilation slots to ensure safe and proper operation.

When needed
Check moving parts for damage

Inspect moving parts for correct function, binding, breakage, or damage before each use.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend PTK 14 EDT?

Yes No
0
User Pic

Anna Kowalski

9 months ago

Is the Bosch PTK14E really worth the higher price compared to cheaper staplers, and will it work well with Bosch staples/clips?

0
User Pic

Manual.ly

9 months ago

Yes. Reviewers consistently say the PTK14E is a good choice for home use and delivers reliable tacking performance. Many users prefer it over cheaper models because it is more durable and generally higher in build quality. Also, when used with the matching Bosch brackets/staples, the tool is reported to work very smoothly and comfortably. If you are looking for a stapler that will last longer and do the job cleanly, the PTK14E is commonly recommended despite the slightly higher price.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

The PTK 14 EDT accepts Bosch staple strips (Type 53) with widths of 11.4 mm and lengths from 6–14 mm, and Bosch nail strips (Type 48) up to 14 mm length. It cannot process 19 mm staples.

Is this answer helpful?

A

Slide the DuoTac selector switch up to fire two staples simultaneously; use it for thin materials like fabric or foil to increase tear resistance. DuoTac is not available when processing nails.

Is this answer helpful?

A

Always unplug before maintenance. Keep ventilation slots clean. To clear jams, unplug, turn the tool over, press the magazine release, pull the magazine out, remove the jammed staple with pliers if needed, then reinsert the magazine until it locks.

Is this answer helpful?

A

The tool is designed for short-time duty (S2) with a maximum continuous operating duration of 10 minutes under constant load. After 10 minutes, switch off and allow it to cool to avoid reduced performance and wear.

Is this answer helpful?

A

Yes. Typical sound pressure is about 84 dB(A) and vibration levels are notable; always wear eye protection and hearing protection and follow additional vibration-reduction measures like warmed hands and work organization.

Is this answer helpful?

A

Bosch recommends using only original Bosch fasteners matched to the magazine, striker and shot duct. Other manufacturers’ fasteners may use different steel qualities or dimensions and can cause jams or damage.

Is this answer helpful?

A

For spare parts, repairs or application advice, contact Bosch service via regional numbers or visit the Bosch Power Tools website. When ordering parts, provide the 10-digit article number from the tool’s nameplate.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Dual-mode: acts as both a stapler and nailer for versatile fastening in DIY projects.
  • DuoTac function doubles staples for improved tear resistance in thin materials.
  • Compact and lightweight (≈1.1 kg) for reduced user fatigue and easier handling.
  • Thumbwheel hammer-force preselection allows material-specific power adjustment.
  • Large magazine capacity (up to 100 fasteners) reduces reload frequency.
VS

Disadvantages

  • Short-time duty (S2) limits continuous use to 10 minutes before cooling is needed.
  • DuoTac function cannot be used with nails, limiting versatility for some tasks.
  • Not suitable for 19 mm staples or heavy-duty wall/ceiling panel fastening.
  • Noise (84 dB(A)) and vibration (ah ≈ 7.5 m/s²) require PPE and breaks.
  • Mains-powered only—no cordless option, limiting portability in remote locations.
M: OA-GPT-5-NAN

Product Specification

Magazine type

Staples (0.24-0.55 in), Nails (0.55 in)

Magazine capacity

100 Staples

Rate of fire

30/min

Features

Softgrip

Weight

2.43 lbs

Package contents

1000 Staples

M: OA-GPT-54-NAN

Product Description

Bosch DIY PTK 14 EDT Electric Stapler/Nailer Manual

The Bosch DIY PTK 14 EDT is a compact, mains-powered electric stapler and nailer engineered for reliable light to medium fastening tasks on wood and wood-like materials. Designed for DIY enthusiasts and occasional professional use, the tool handles staple lengths from 6 to 14 mm and nail strips up to 14 mm, with a magazine capacity of up to 100 fasteners and an impact rate of approximately 130 strokes/min. Weighing about 1.1 kg and built to EPTA standards, the PTK 14 EDT balances portability with performance for upholstery, insulation, fabric, cardboard, foils and similar materials.

Features and operation

The PTK 14 EDT includes a movable tacker head with an integrated trigger lock to prevent accidental firing, a DuoTac selector for doubling up staples when extra tear resistance is needed, and a thumbwheel for hammer-force preselection to match material density and fastener length. The DuoTac mode doubles staple thickness for delicate materials but is not available for nails. Users can choose single actuation or contact actuation for faster successive fastening. To load the tool, pull out the magazine, insert the staple or nail strip (holding nail strips at a slight angle so nails seat correctly), and snap the magazine back until it locks.

Safety and duty

Bosch emphasizes comprehensive safety: always disconnect mains power before maintenance or loading, wear eye and hearing protection, avoid working in wet or explosive atmospheres, and keep bystanders away. The tool is rated for short-time duty (S2) with a recommended continuous operating limit of 10 minutes under constant load; allow cooling intervals to preserve performance and prevent overheating. Use original Bosch fasteners and replacement parts to ensure fit and safe operation.

Maintenance and support

Routine cleaning of ventilation slots and the device exterior is important. If fasteners jam, disconnect power, remove the magazine, clear the jam (use pliers if necessary), and reinsert the magazine. Replacement of the mains lead must be done by Bosch or an authorized service agent. Bosch provides spare parts, exploded views, and service contacts through regional support channels and online resources.

Practical tips

Test hammer-force settings on scrap material before full use; increase force one step when using DuoTac; avoid blank shots to reduce striker wear; secure workpieces with clamps when possible. The typical A-weighted sound pressure is 84 dB(A); wear hearing protection. Vibration emissions are specified (ah ≈ 7.5 m/s²) — consider work patterns and breaks to reduce exposure.

Notes

  • Intended use: fastening cardboard, insulation, fabric, foils, leather and similar materials onto wood or wood-like substrates; not intended for wall or ceiling panelling attachment.
  • Use only original Bosch staples and nails sized to the tool’s specifications. Keep children and untrained persons away from the device.
  • Dispose of the tool and accessories according to local environmental regulations; do not put them in household waste.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly