Manual.ly Logo

Bosch DIY PKP 18 E Manual

4.6 · 34 Ratings

PDF manual · 40 Pages

English

M: OA-GPT-5-NAN
page

/ 40

Loading...
2a438421ac87ccf8999cedd7e2da161218b5 page 7
English | 7
Bosch Power Tools 1 609 92A 1LK | (12.11.15)
danger of operating errors and inju-
ries.
Supervise children. This will ensure
that children do not play with the glue
gun.
Children must not be allowed to
clean and perform maintenance on
the glue gun without supervision.
Do not allow persons unfamiliar with the glue gun or
these instructions to operate the device.
Before each use of the unit, check the glue gun, cable
and plug. If damage is detected, do not use the glue
gun. Never open the glue gun yourself, and have re-
pairs carried out only by a qualified repair person using
only identical replacement parts. Damaged glue guns,
cables and plugs increase the risk of an electric shock.
Do not leave the switched on glue gun unattended.
Keep the glue gun away from rain or moisture. The pen-
etration of water into the glue gun increases the risk of an
electric shock.
When operating the glue gun in damp environments is
unavoidable, use a residual current device (RCD). The
use of a residual current device (RCD) reduces the risk of
an electric shock.
Do not touch the hot nozzle. Danger of burns.
The mains plug of the glue gun must match the socket
outlet. Never modify the plug in any way. Unmodified
plugs and matching outlets will reduce the risk of electric
shock.
Do not misuse the cord to carry the glue gun, hang it up,
or for pulling the plug out of the outlet. Keep the cord
away from heat, oil, sharp edges or moving parts. Dam-
aged or entangled cords increase the risk of electric shock.
Have your glue gun repaired only through a qualified
repair person and only using original replacement
parts. This will ensure that the safety of the product is
maintained.
After use, place down the glue gun in a safe manner and
allow it to cool down completely before packing it
away. The hot nozzle can cause damage and/or burns.
Do not use the cable for pulling the plug out of the sock-
et outlet. Keep the cable away from heat or oil. Damaged
or entangled cables increase the risk of an electric shock.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Intended Use
The glue gun is intended for the quick gluing of clean, dry and
grease-free materials with hot-melt adhesives.
Use the glue gun only when you fully understand and can per-
form all functions without limitation, or have received appro-
priate instructions.
Product Features
The numbering of the product features refers to the illustra-
tion of the glue gun on the graphics page.
1 Nozzle
2 Heat protection cover
3 Glue stick
4 Feed trigger
5 Support stand
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Assembly
–Screw a nozzle 1 onto the glue gun. Insert the support
stand 5 into the openings on both sides of the glue gun.
Glue Gun PKP 18 E
Article number
0 603 264 5..
Rated power input
–for heating up
– for maintaining heat
W
W
200
16
Heating time
min 7
Gluing temperature
°C 200
Gluing capacity
g/min 20
Glue stick diameter
mm 11
Glue stick length
mm 45–200
Weight according to EPTA-
Procedure 01:2014 kg 0.35
Protection class
/II
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
OBJ_BUCH-868-004.book Page 7 Thursday, November 12, 2015 11:50 AM

Chat with your Bosch DIY PKP 18 E manual using AI

Get instant AI answers from your Bosch DIY PKP 18 E manual

Ask anything about the Bosch DIY PKP 18 E. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend PKP 18 E?

Yes No
0
User Pic

minima39

10 months ago

Does the hot glue gun really avoid dripping? Some reviews say the drip stop does not work and glue comes out messy. How can I prevent it?

0
User Pic

Manual.ly

10 months ago

The drip stop on hot glue guns can be affected by heating time, angle, and how fast you change pressure. For best results, let the gun fully preheat before applying glue, keep it mostly upright during use, and use the stand to wait between runs. If you notice a bead forming at the nozzle, pause briefly and wipe the tip with a dry cloth or paper (after it cools slightly) instead of pulling it. Place a paper towel under the nozzle for the first drops. Always use the recommended glue sticks and avoid overfilling pressure. If your unit still leaks even when used correctly, please contact support with your order details for troubleshooting or replacement.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

The PKP 18E accepts 11 mm diameter glue sticks with lengths from about 45 mm up to 200 mm. Use adhesive types suitable for hot-melt application and the materials you are bonding.

Is this answer helpful?

A

Allow roughly 7 minutes for the gun to reach working temperature. After heating, the tool maintains heat; if extrusion becomes thick the gun can be plugged in again to reheat.

Is this answer helpful?

A

Check cable and plug before use, avoid moisture, do not touch the hot nozzle (≈200 °C), supervise children, use an RCD in damp conditions, rest the gun on its support stand, unplug during long breaks and have repairs done by authorized service using original parts.

Is this answer helpful?

A

Yes — only when the gun is warm. Heat for ~2 minutes, wear protective gloves, grasp the nozzle via the heat shield and screw the new nozzle hand-tight. Avoid touching the hot tip to prevent burns.

Is this answer helpful?

A

Press glued parts together for about 30 seconds after application. The bond is typically loadable after approximately 5 minutes of cooling, though final strength may vary by materials and conditions.

Is this answer helpful?

A

The tool is designed for mains operation at the voltage indicated on its type plate (models for 230 V can operate at 220 V). Always verify the voltage matches your supply before use.

Is this answer helpful?

A

Unplug before cleaning or maintenance and keep the tool clean. If the supply cord needs replacement or the tool requires repair, have Bosch or an authorized service agent perform the work using original spare parts to ensure safety.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Fast preheat (≈7 min) and steady 200 °C operating temperature for reliable melt flow.
  • Compact, lightweight (≈0.35 kg) design reduces user fatigue for craft and repair tasks.
  • Accepts common 11 mm glue sticks (45–200 mm) with ~20 g/min dispensing rate.
  • Heat protection cover and support stand improve safe handling and resting between uses.
  • Double-insulated (Class II) and backed by Bosch service network and spare parts access.
VS

Disadvantages

  • No variable temperature control — fixed ~200 °C may be hot for delicate materials.
  • Requires mains power and ~7 min preheat, limiting instant or portable use without outlet.
  • No rear removal for an inserted glue stick; some jam/clear procedures are limited.
  • Noisy or heavy-duty glue demands could exceed the 20 g/min capacity for industrial jobs.
  • Nozzle changes require warm tool and protective gloves — minor inconvenience for swaps.
M: OA-GPT-5-NAN

Product Specification

Power

200 W

Temperature

392°F

Heating time

7 min

Glue stick diameter

0.43 in

Special features

Drip protection, Stand bracket

Weight

0.77 lb

Scope of delivery

1x Glue cartridge, 1x Long nozzle

M: OA-GPT-54-NAN

Product Description

Bosch DIY PKP 18E Electric Hot Glue Gun Manual

The Bosch DIY PKP 18E is a compact, corded hot glue gun engineered for fast, reliable bonding of clean, dry and grease-free materials. With a 200 W heating element and a 200 °C operating temperature, it reaches working temperature in about 7 minutes and maintains consistent melt flow for steady application. Designed for hobbyists, DIYers and light workshop tasks, the PKP 18E accepts 11 mm glue sticks (45–200 mm length) and provides an estimated glue output of about 20 g/min, making it well suited to crafts, minor repairs, assembly and decorative projects.

Ergonomically the tool features a heat-protection cover over the nozzle, a feed trigger for controlled dispensing and a fold-out support stand so the gun can be rested safely between applications. The replaceable nozzle can be changed when warm (wear gloves and handle via the heat shield), while the integrated heat reservoir allows brief use even after unplugging. The gun is double-insulated (Protection class II) and weighs approximately 0.35 kg, keeping user fatigue to a minimum for extended jobs.

Operational guidance in the manual stresses safety and correct preparation: verify mains voltage before use, allow the gun to heat for ~7 minutes, insert glue stick from the rear and apply with moderate trigger pressure. Apply adhesive in dots or zigzag lines (for flexible materials), press parts together for about 30 seconds and allow ~5 minutes cooling before loading the joint. Surfaces should be clean, dry and degreased; roughen smooth areas for better adhesion. Avoid flammable solvents and work only within ambient and material temperature ranges (+5 °C to +50 °C).

Maintenance and service sections recommend unplugging before cleaning, keeping the tool clean, and having repairs or cord replacements performed only by Bosch or an authorized service center using original parts. The manual also outlines disposal guidance per EU WEEE rules and provides contact details for Bosch service and spare parts in multiple regions.

Notes: the nozzle reaches high temperature and can burn; hot glue can cause burns—if contact occurs, cool the area under cold running water and do not attempt to remove hardened glue from skin. When changing the nozzle, heat the gun briefly (~2 minutes), use protective gloves and tighten the new nozzle by hand.

Quick specs

  • Rated power: 200 W (heating) / 16 W (maintenance)
  • Heating time: ~7 min
  • Glue temperature: ~200 °C
  • Glue stick diameter: 11 mm, length 45–200 mm
  • Glue output: ~20 g/min
  • Weight: ~0.35 kg
  • Protection class: II

Notes:

  • Always check cable, plug and tool for damage before use.
  • Do not leave the gun switched on and unattended.
  • Use an RCD in damp environments.
  • Replace parts only with original Bosch spare parts via authorized service.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly