Manual.ly Logo

Bosch DIY EasyAquatak 100 Manual

4.0 · 1 Ratings

PDF manual · 39 Pages

English

M: OA-GPT-5-NAN
page

/ 39

Loading...
e27654898013cc23a7a90c3d62d08da74b8b page 9
English | 9
Bosch Power Tools F 016 L81 746 | (26.10.17)
Maintenance and Service
Maintenance
Stop, remove plug from the power supply and discon-
nect from water supply.
Note: To ensure long and reliable service, carry out the follow-
ing maintenance regularly.
Regularly check for obvious defects such as loose fixings, and
worn or damaged components.
Check that covers and guards are undamaged and correctly
fitted. Carry out necessary maintenance or repairs before us-
ing.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After use/Storage
Turn the main switch off and operate the trigger to drain the
water from the high pressure hose.
Clean the exterior of the machine thoroughly using a soft
brush or cloth. Do not use water, solvents or polishes. Re-
move all debris, especially from the ventilation slots.
End of season storage: Drain water out of pump running mo-
tor for a few seconds. Pull trigger to release all water.
Do not place other objects on top of the machine.
Store in a frost-free area.
Ensure cables are not trapped when storing. Do not kink high
pressure hose.
After-sales Service and Application Service
www.bosch-do-it.com
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the machine.
Motor “sounds” but fails to start Insufficient power supply Check that the voltage of the mains power supply
line is the same as that on the plate
Voltage loss due to use of extension
cable
Check characteristics of extension cable
Appliance not used for a long period
of time
Contact your Bosch Service Centre
Problems with TSS (Total Stop Sys-
tem) device
Contact your Bosch Service Centre
Pressure pulsating Air in the inlet water supply
hose/pump
Allow pressure washer to run with open spray han-
dle and nozzle at low pressure until regular working
pressure is obtained
Inadequate water supply Check that the water supply corresponds to specifi-
cations. The minimum specification for the water
supply hose is 1/2" or 13 mm diameter
Water filter blocked Clean water filter
Water supply hoses squeezed Straighten out kinked water supply hoses
High pressure hose too long Remove high pressure extension hose. Retry (ex-
tension hose max. 7 m)
Pressure too low, but steady
Note: Several types of accessory
will normally deliver a lower pres-
sure
Nozzle worn Change the nozzle
Start/stop valve worn Activate trigger five times in quick succession
Motor starts up but with restricted
or no working pressure
No water supply Connect water supply
Water filter clogged up Clean the water filter
Nozzle clogged up Clean nozzle
The pressure washer starts irregu-
larly by itself
Pump/spray gun leaky Contact your Bosch Service Centre
Water leaks from machine Leaking pump A slight water leak is permissible; in case of exces-
sive leak, contact Bosch Service Centre
Problem Possible Cause Corrective Action
OBJ_BUCH-3419-001.book Page 9 Thursday, October 26, 2017 10:34 AM

Chat with your Bosch DIY EasyAquatak 100 manual using AI

Get instant AI answers from your Bosch DIY EasyAquatak 100 manual

Ask anything about the Bosch DIY EasyAquatak 100. Answers come from this manual, with the pages they are based on.

EasyAquatak 100 Maintenance Schedule

Remind me when maintenance is due
Monthly
Check for defects and damage

Regularly check for loose fixings, worn or damaged components, and ensure covers and guards are undamaged and correctly fitted.

After each use
Drain water from pump and hose

Turn off the main switch and operate the trigger to drain all water from the high-pressure hose and pump.

After each use
Clean exterior and remove debris

Thoroughly clean the machine exterior with a soft brush or cloth. Remove debris, especially from ventilation slots.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend EasyAquatak 100?

Yes No
0
User Pic

Mia Schmidt

10 months ago

Does this device clean garden furniture effectively even when using cold water, and is the price around 80 euros reasonable?

0
User Pic

Manual.ly

10 months ago

Yes. Customers report good cleaning results on garden furniture, including when using cold water instead of hot. The device is considered solid and effective for typical outdoor cleaning tasks. Regarding value, a price around 80 EUR is described as fair for the performance and overall quality, especially for occasional or borrowed use.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Product Specification

Operating mode

Cold water

Power

1200W

Pressure

1450.38psi

Flow rate

max. 79.25gal/h

Inlet temperature

max. 104°F

Mobility

Carry handle

Fuel tank

no

Weight

6.61lb

Scope of delivery

High-pressure gun, high-pressure hose (3m), nozzle (detergent nozzle), detergent, water filter

M: OA-GPT-54-NAN

Product Description

M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly