Manual.ly Logo

Axing SAA 85 Manual

0.0 · 0 Ratings

PDF manual · 4 Pages

English

M: QW-35-FL
page

/ 4

Loading...
f58f5c28f75b6ba2cc90fbde09471d2e8750 page 3
Manufacturer
AXING AG
Gewerbehaus Moskau
8262 Ramsen
EEA contact address
Bechler GmbH
Am Rebberg 44
78239 Rielasingen
State of the art 2019-12-06
Technical improvements, changes in design, printing- and other errors expected.
Safety advices:
Prior to the installation of this parabolic aerial, it is essential that
these safety instructions are observed! Failure to comply with these
instructions may result in injury or even death. The manufacturer is not
liable in case of improper installation and connection errors.
Under no circumstances may the antenna be installed under or in close
proximity to overhead power lines! A minimum lateral distance of >1
m from any electrical equipment must be observed. Touching electrical
installations may cause death!
Never work on antennas during thunderstorms or when a thunderstorm
is approaching. There is a risk of death!
Never install antennas on buildings with inflammable roof coverings
such as in thatched roofs! In such cases there is a fire hazard due to
atmospheric surge voltages (static electricity) or lightning (e.g. during
thunderstorms).
The installation procedure described herein requires good technical
skills and knowledge on properties of materials when exposed to wind.
Therefore, have the work executed by a trained technician in case you do
not have these skills yourself.
The person executing the installation must wear sturdy antislip-footwear,
should have no fear of heights, be able to move safely on the roof
and have a secured standing and holding position (e.g. by using belts
connected to the roof).
Check whether the roof can support your weight. Never step on cracked
or non-load-bearing areas! If in doubt, consult a qualified dealer or
roofing craftsman to determine a suitable installation position.
Enter roofs or areas with a risk of falling only with a safety harness that
is properly worn and free of defects or use a work platform.
Ladders or other climbing aids must be in good order and condition (dry,
clean and slip-resistant).
If there is a possibility that there may be a hazard to pedestrians due to
falling objects during installation, you must block the hazard zone! Make
sure that there are no persons present below the location of installation.
Falling from or through the roof and falling parts can cause death and
significant material damage. The manufacturer cannot be held liable for
such damage.
The applicable national safety regulations and current standards such as
DIN EN 60728-11 must be observed.
SAA 85-0x | SAA 110-0x
premium-line
Aluminium
satellite antennas
85 cm | 110 cm
Operation instructions
Technical data:
Type SAA 85-01 SAA 85-02 SAA 85-03
Electrical data
Frequency range 10,75/11,75/12,75 GHz
Antenna gain 38,12...39,53 dB
Full width at half
maximum
< 2,2°
Mechanical data
Reflector dimensions 85 x 85 cm
Reflector colour grey anthracite brick-red
Reflector material Aluminium
Elevation range 15...50°
Diameter of feed 40 mm
Mast diameter 32...76 mm
Wind load at max. wind
speed [20/40/60m/s]
21,3 kg/85,4 kg/192,1 kg
Back part material Zinc coated steel, including plastic coupler
Screw sets material Dacromet
Type SAA 110-01 SAA 110-02 SAA 110-03
Electrical data
Frequency range 10,75/11,75/12,75 GHz
Antenna gain 39,8...40,9 dB
Full width at half
maximum
< 1,8°
Mechanical data
Reflector dimensions 110 x 99 cm
Reflector colour grey anthracite brick-red
Reflector material Aluminium
Elevation range 5...70°
Diameter of feed 40 mm
Mast diameter 32...76 mm
Wind load at max. wind
speed [20/40/60m/s]
30 kg/119 kg/268 kg
Back part material Zinc coated steel, including plastic coupler
Screw sets material Stainless steel
Herewith AXING AG declares that the marked products comply with the valid
guidelines.
WEEE Nr. DE26869279 | Electrical and electronic components must not be
disposed of as residual waste, it must be disposed of separately.

Chat with your Axing SAA 85 manual using AI

Get instant AI answers from your Axing SAA 85 manual

Ask anything about the Axing SAA 85. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend SAA 85?

Yes No

Frequently Asked Questions

A

The Axing Sat Mirror 85cm Grey supports a frequency range of 10.75 GHz, 11.75 GHz, and 12.75 GHz, making it ideal for standard satellite television reception.

Is this answer helpful?

A

No, the Low Noise Block (LNB) converter is not part of the delivery scope. You must purchase a compatible LNB separately to receive satellite signals.

Is this answer helpful?

A

You can mount the physical structure, but all grounding and lightning protection work must be performed by a trained professional to ensure safety and compliance with regulations.

Is this answer helpful?

A

At maximum wind speeds of 60 m/s, the antenna can withstand a wind load of up to 192.1 kg, provided it is installed according to the specified technical guidelines.

Is this answer helpful?

A

Yes, do not install it under power lines, on flammable roofs, or on vibrating structures. It must be grounded properly unless placed more than 2 meters below the roof edge.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High gain between 38.12 and 39.53 dB for excellent signal quality
  • Durable aluminum reflector with anti-corrosion zinc-coated steel backing
  • Wide elevation range of 15 to 50 degrees for flexible satellite positioning
  • Compatible with multifeed bars for receiving multiple satellite signals
  • Complies with strict European safety standards like DIN EN 60728-11
VS

Disadvantages

  • LNB and multifeed bar not included in the standard delivery scope
  • Requires professional installation for safe grounding and lightning protection
  • Not suitable for installation on vibrating or unstable structures
  • Strict torque limits require careful adjustment during assembly
  • Cannot be used for commercial purposes without voiding the warranty
M: QW-35-FL

Product Specification

Diameter

33.46 inches

Reflector Material

Aluminum

Color

Gray

M: QW-35-FL

Product Description

The Axing Sat Mirror 85cm Grey: A Premium Satellite Solution

The Axing Sat Mirror 85cm Grey is a high-performance aluminum satellite antenna designed specifically for domestic use. This premium-line model, identified as the SAA 85-0x series, offers exceptional signal reception capabilities with a reflector size of 85 by 85 centimeters. Its sleek grey anthracite finish not only provides durability but also ensures it blends seamlessly into various architectural styles. Manufactured by AXING AG, this device is engineered to receive signals from specific satellite positions using a compatible LNB.

Constructed from robust aluminum, the reflector is built to withstand varying weather conditions while maintaining structural integrity. The antenna features an elevation range of 15 to 50 degrees, allowing for precise alignment with satellites in different orbital positions. The back part is made of zinc-coated steel with plastic couplers, ensuring long-term resistance against corrosion. For optimal performance, the unit supports a feed diameter of 40 mm and fits masts ranging from 32 to 76 mm in diameter. It is important to note that the LNB and multifeed bars are sold separately, giving users the flexibility to choose components that best suit their specific setup.

Safety is paramount during the installation process. The product manual emphasizes strict adherence to safety guidelines, including avoiding installation near overhead power lines and never working on the roof during thunderstorms. Professional installation is highly recommended for those without specific technical skills or proper safety equipment. Proper grounding and lightning protection must be executed by qualified electricians to comply with DIN EN 60728-11 standards. The antenna is not suitable for structures prone to vibration and must be mounted on stable surfaces capable of supporting its weight and wind load.

Key Features and Installation Notes

When installing the Axing Sat Mirror 85cm Grey, ensure you use the included mounting screws and adhere to torque specifications. The maximum torque for reflector screws is 10 Nm, while side and rear wing nuts should not exceed 5 Nm. Cable management varies by model; the 85cm version utilizes cable clips, whereas larger models route cables through a hollow LNB arm. Always verify that the mast is vertical and secure before finalizing the alignment. Remember that any unauthorized modification voids the warranty and may compromise safety.

Important Safety Reminders

  • Never install on roofs with flammable materials like thatch.
  • Ensure a minimum lateral distance of over 1 meter from electrical equipment.
  • Use a safety harness when working at heights.
  • Do not route cables through rooms storing flammable substances.
  • Grounding is mandatory unless installed more than 2 meters below the roof edge.
M: QW-35-FL

© Copyright 2026 Manual.ly