Manual.ly Logo

Atika HHS 710/56 Manual

0.0 · 0 Ratings

PDF manual · 120 Pages

English

M: QW-35-FL
page

/ 120

Loading...
d0415b7e4eda03caa1561c2c7c56beea3d3b page 13
19
Safety instructions for hedge trimmers
• Keep away all body parts from the cutting blades. Do not
attempt to remove cut material or to hold material to be
cut while the cutting tool is in operation. Only remove
jammed material after the unit was switched off. A single
moment of inadvertence when using the hedge shear may
result in severe injury.
• Make sure that all protective devices and handles are
attached before using the unit. Never attempt to put into
service an incomplete unit or a unit that was improperly
modified.
• Carry the hedge shear on its handle with the cutting tool
stopped. Always install the guard when transporting or
storing the hedge shear. A careful handling of the unit
minimises the risk of injury by the cutting tool.
• Always hold the power tool on the insulated handle
surfaces as the cutting blades may come into contact
with hidden power cables or the unit's mains supply
cable. A contact of the cutting blades with a live conductor
may apply hazardous voltage to metallic parts of the unit and
cause electric shock.
• Keep the cable away from the cutting area. During the
work, the cable may be hidden by shrubbery and accidentally
cut.
• This device is not intended to be used by persons (including
children) with restricted physical, sensory or mental abilities
or a lack of experience and/or know-how unless they are
supervised by a person responsible for their safety or they
have been instructed by such a person on the use of the
device.
Supervise children to make sure they do not play with the
device.
more safety warnings
„Electrical safety“
• Design of the connection cable according to IEC 60245 (H
07 RN-F) with a core cross-section of at least
− 1.5 mm² for cable lengths up to 25 m
− 2.5 mm² for cable lengths over 25 m
• Long and thin connection lines result in a voltage drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
• Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
• The connector of the connection cable must be splash-proof.
• When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
• During the cutting operation, the supply cord must be
securely positioned to prevent the cord from snagged on
branches and the like.
• Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges.
• Wind off completely the cable when using a cable drum.
• Regularly check the cables and replace them if they are
damaged.
• Do not use any defective connection cables.
• Do not set up any provisional electrical connections.
• Do not hose down the device with water. (origin of danger
electric current).
• Never bypass protective devices or deactivate them.
• Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
• The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one
of our customer service points. Local regulations – especially
regarding protective measures – must be observed.
more safety warnings
„Personal safety“
• The operator is responsible to third persons within the area
of operations.
• Adhere to national regulations that might specify an age limit
for the user of the unit.
• Wear suitable protective equipment when working:
− hairnet in case of long hair
− protection gloves
− eye and ear protection
more safety warnings
„Power tool use and care“
• Do not modify the device or parts of the device respectively.
• After a longer period of use, accessible metallic parts and
accessories may be hot.
• Switch off machine and pull out power plug out of the power
outlet in case of:
the cutting tool comes into contact with soil, stones, nails
or other foreign objects ( check whether the cutting
tool/machine is damaged)
− Carrying out repair work.
− Performing maintenance and cleaning work.
− Removal of faults (including blocking of knives).
− Transport.
− Leaving the machine (also during temporary
interruption).
• Check the machine for possible damage:
− Before further use of the machine the safety devices
must be checked carefully for their proper and intended
function. Only operate the machine with complete and
correctly attached safety equipment and do not alter
anything on the machine that could impair the safety.
− Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must
be correctly installed and fill all conditions to ensure
perfect operation of the machine.
− Damaged safety devices and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
− Damaged or illegible safety labels have to be replaced.
• Store unused devices in a dry, locked place.

Chat with your Atika HHS 710/56 manual using AI

Get instant AI answers from your Atika HHS 710/56 manual

Ask anything about the Atika HHS 710/56. Answers come from this manual, with the pages they are based on.

HHS 710/56 Maintenance Schedule

After each use
Clean the machine and accessories

Clean the case with a soft brush or dry cloth. Never use water, solvents, or polishing agents on the housing.

Show in the manual (page 22)
Regularly
Clean the cutting blades

Clean the knives regularly with a brush or cloth. Never clean the knives with water to prevent corrosion.

Show in the manual (page 22)
Regularly
Oil the cutting tools

Oil the cutting tools regularly using environmentally friendly oil. Never use grease.

Show in the manual (page 22)
Regularly
Inspect for obvious defects

Check for loose, damaged, or worn cutting tools and components. Ensure covers and protective devices are intact and correctly mounted.

Show in the manual (page 22)
Regularly
Check connection cables

Regularly check the power cord and extension cables. Replace them immediately if they are damaged.

Show in the manual (page 19)
Before long-term storage
Prepare for extended storage

Thoroughly clean the trimmer and treat all movable parts with environmentally friendly oil. Fit the knife protection before storing in a dry place.

Show in the manual (page 22)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend HHS 710/56?

Yes No

Frequently Asked Questions

A

The maximum cutting diameter for this model is 27 mm. It is designed for fresh shoots and soft branches. Cutting thicker wood may damage the blades or strain the motor.

Is this answer helpful?

A

To adjust the height, loosen the cap nut located on the telescopic tube. Slide the tube to your desired length and then retighten the cap nut securely to lock it in place.

Is this answer helpful?

A

No, this device is strictly for cutting hedges, shrubs, and ground-cover plants. Using it on grass or for composting poses a serious risk of injury and will void the warranty.

Is this answer helpful?

A

Yes, the cutting head can be swiveled within a range of 0 to 100 degrees across six distinct positions, allowing for precise trimming of difficult angles.

Is this answer helpful?

A

You should oil the blades regularly after every few uses or whenever they appear dry. Use environmentally friendly oil and never use grease to prevent corrosion and ensure smooth cutting.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 710 W motor ensures efficient cutting through thick branches
  • Telescopic handle extends reach up to 2.8 meters for high hedges
  • Swiveling cutting head allows 100-degree range for complex angles
  • Adjustable rear handle fits five positions for user comfort
  • Two-hand safety switch prevents accidental start-ups
VS

Disadvantages

  • Corded operation limits mobility compared to battery models
  • Blade length may be insufficient for very large commercial properties
  • Requires careful handling of the cable to avoid cutting damage
  • Weight increases slightly when fully extended with telescopic pole
  • Not suitable for cutting grass or woody stems over 27 mm diameter
M: QW-35-FL

Product Specification

Type

Hedge trimmer

Power

710W

Cutting length

20.08 in

Cutting thickness

1.06 in

Features

Soft grip, telescopic

Weight

9.04 lbs

M: QW-35-FL

Product Description

Master Your Garden with the Atika HHS 710/56 Electric Hedge Trimmer

The Atika HHS 710/56 Electric Hedge Trimmer is a robust tool designed specifically for homeowners and hobby gardeners who demand precision and power. This telescopic hedge trimmer combines a powerful 710-watt motor with a versatile design, allowing you to tackle everything from low ground covers to tall, wide hedges with ease. The inclusion of a telescopic pole extends your reach significantly, reducing the need for ladders and making high trimming tasks safer and more manageable.

Equipped with dual-sided blades measuring 510 mm in cutting length and a blade span of 27 mm, this machine handles fresh branches and soft shoots efficiently. The ergonomic design features adjustable rear handles that can be rotated into five different positions, ensuring a comfortable grip regardless of the angle required. Furthermore, the swiveling cutting head offers six working positions ranging from 0 to 100 degrees, providing exceptional flexibility for detailed shaping and hard-to-reach areas.

Safety is paramount with the Atika HHS 710/56. It features a two-hand safety switch system that prevents accidental activation, requiring simultaneous pressure on both the front trigger and the main switch to operate. The unit also includes a carrying strap to distribute weight during extended use and a knife protection cover for safe storage. Regular maintenance is simple, involving cleaning with a dry cloth and regular oiling of the blades to prevent rust and ensure smooth operation.

Whether you are maintaining a formal garden or simply keeping your property tidy, this manual highlights the importance of reading all instructions before use to maximize performance and safety. By adhering to the guidelines regarding noise restrictions and electrical safety, users can enjoy years of reliable service from this high-quality electric hedge trimmer.

M: QW-35-FL

© Copyright 2026 Manual.ly