Manual.ly Logo

Arai Chaser-X Manual

0.0 · 0 Ratings

PDF manual · 52 Pages

English

M: QW-35-FL
page

/ 52

Loading...
486b4f5125bc6b71a016bfb1c47dac7fe477 page 6
6
English
WARNING:
If your shield becomes too scratched or uncleanable, replace it with a new one.
Impaired visibility causes accidents.
Use a solution of mild soap or detergent and lukewarm water to clean your
shield. Rinse well with clean water, and wipe off with a soft cloth. Never use
petrol, thinner, benzene or any other solvents. There are many “aggressive”
cleaners on the market, including some supposed to be specifically for use on
shield. Arai strongly recommends that you do not use any such products to
clean your shield as some of their ingredients may have damaging effects on
the shield and other plastic parts installed on your helmet.
Do not apply stickers or adhesive tape to the shield, as this will weaken the hard
coating. If tinted, the shield is for daylight use only.
TO OPERATE DEMIST SYSTEM
A demist function is incorporated in the shield latch system to allow more
rapid clearing of any interior mist with the shield remaining partially latched.
Push the shield latch lever up to release shield into the demist position to
assist moisture dispersal ①. To close the shield completely, push the shield
down until the latch post fully engages the shield and latch lever captures the
bottom of the shield ②.
TO OPERATE BROWVENTS
The Browvents are operated from fully closed through intermediate, to fully open
positions by simply pulling the vent control down to open, pushing up to close.
①
②

Chat with your Arai Chaser-X manual using AI

Get instant AI answers from your Arai Chaser-X manual

Ask anything about the Arai Chaser-X. Answers come from this manual, with the pages they are based on.

Chaser-X Maintenance Schedule

As needed
Clean the shield

Use mild soap and lukewarm water. Rinse well and wipe with a soft cloth. Never use petrol, thinner, benzene or other solvents.

As needed
Lubricate shield mechanism

If shield operation becomes stiff, apply one or two drops of silicone lubricant around the sliding slot and brass stud, then wipe off excess.

As needed
Wash cheekpad fabric covers

Hand wash in lukewarm water with mild soap or shampoo. Rinse well, wipe with a soft cloth, and dry in shade at ambient temperature.

Show in the manual (page 12)
As needed
Wash comfort lining

Hand wash in lukewarm water with mild soap or shampoo. Rinse well, wipe with a soft cloth, and dry in shade at ambient temperature.

Show in the manual (page 16)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Chaser-X?

Yes No

Frequently Asked Questions

A

You must only use original Arai visors such as the VAS-V IC (Max Vision), VAS-V, VAS-V 2D (Top), or VAS-V Pro-Shade types. Using other brands may affect safety and fit.

Is this answer helpful?

A

Use a solution of mild soap or detergent and lukewarm water. Rinse well and wipe with a soft cloth. Never use petrol, thinner, benzene, or aggressive cleaners as they damage the coating.

Is this answer helpful?

A

Apply one or two drops of the supplied silicone lubricant around the sliding slot and brass stud. Wipe off excess with a soft tissue paper to restore smooth operation.

Is this answer helpful?

A

Yes, remove them and wash gently by hand in lukewarm water with a small amount of laundry soap or shampoo. Rinse well and dry in the shade at ambient temperature.

Is this answer helpful?

A

Applying stickers or adhesive tape weakens the hard coating of the shield, potentially reducing visibility and durability over time.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Advanced demist system integrated into the shield latch for rapid fog clearing
  • Multi-directional ventilation with brow, mouth, and top vents for optimal airflow
  • High-quality original visor compatibility ensures perfect fit and safety
  • Removable and washable comfort lining and cheek pads for easy maintenance
  • Robust construction designed to withstand wind pressure and vibrations
VS

Disadvantages

  • Requires strict adherence to using only specific original Arai visors
  • Shield removal and replacement process requires careful alignment steps
  • Cleaning agents must be strictly mild; solvents cause permanent damage
  • Base plate screws must not be overtightened to prevent breakage
  • Lubrication is limited to supplied silicone oil; oils and waxes are prohibited
M: QW-35-FL

Product Specification

Type

Full-face helmet

Weight

3.59 lbs

M: QW-35-FL

Product Description

Arai Chaser X: The Ultimate Modular Helmet Experience

The Arai Chaser X stands as a pinnacle of motorcycle safety and comfort, designed for riders who demand the best in protection without sacrificing style. This modular helmet features a sophisticated shield system that allows for effortless operation, ensuring clear vision in all conditions. The integrated demist function works seamlessly with the latch mechanism to quickly disperse interior moisture, keeping your view unobstructed even on cold mornings.

Ventilation is key to rider comfort, and the Chaser X excels here with its multi-point airflow system. The brow vents offer precise control from fully closed to wide open, allowing you to direct fresh air exactly where needed. The mouth vent provides an additional layer of temperature regulation, channeling warm, moist air away from your face while also assisting in anti-fogging when fully open. Top vents complete the package, giving you the ability to manage heat buildup during long rides or stop-and-go traffic.

Maintenance and customization are straightforward thanks to the thoughtful design of the internal components. The cheek pads and comfort lining can be easily removed for washing, ensuring hygiene and longevity. The fabric covers are machine-friendly but require gentle hand washing in lukewarm water with mild soap. It is crucial to avoid harsh chemicals like petrol, thinners, or benzene, as these can damage the plastic parts and the shield coating. When reinstalling any internal part, ensure everything snaps into place correctly to maintain the helmet's structural integrity and safety standards.

The shield itself is compatible only with specific original Arai visors, including the VAS-V IC (Max Vision), VAS-V, VAS-V 2D (Top), and VAS-V Pro-Shade types. Using non-original shields can compromise the fit and safety mechanisms. Cleaning should always be done with mild soap and water, avoiding aggressive cleaners that might weaken the hard coating. Never apply stickers or tape to the shield, as this will degrade its performance. With proper care, the Arai Chaser X remains a reliable companion for every journey.

M: QW-35-FL

© Copyright 2026 Manual.ly