Aosong DHT22/AM2302 Manual
PDF manual · 11 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your Aosong DHT22/AM2302 manual using AI
Get instant AI answers from your Aosong DHT22/AM2302 manual
Ask anything about the Aosong DHT22/AM2302. Answers come from this manual, with the pages they are based on.
Ask a Question
Do you recommend DHT22/AM2302?
Yes NoFrequently Asked Questions
It measures ambient relative humidity and temperature. Humidity is reported from 0 to 99.9% RH, while temperature is measured from -40 C to 80 C.
Is this answer helpful?
The operating supply range is 3.3 V to 5.5 V, with 5 V recommended. A stable supply helps maintain reliable readings and communication.
Is this answer helpful?
Wait at least two seconds between reads. Reading more quickly can produce inaccurate values or failed communication. After a long idle period, two properly spaced readings can provide the newest measurement.
Is this answer helpful?
It uses a single-bus digital data line called SDA. The controller sends a start signal, and the sensor returns 40 bits containing humidity, temperature, and checksum data.
Is this answer helpful?
Yes, a pull-up resistor is normally used on the SDA line. A 5.1 kOhm resistor is a typical recommendation for shorter cable runs, though the value may need adjustment for the installation.
Is this answer helpful?
Place it where air can circulate and keep it away from heat sources, direct sunlight, condensation, corrosive gases, salt spray, and chemical vapors. Mounting it below heat-producing components can reduce thermal interference.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Measures humidity from 0 to 99.9% RH and temperature from -40 C to 80 C.
- Factory calibration and internal coefficients support consistent, interchangeable sensor performance.
- Uses a simple single-bus digital interface that reduces wiring for microcontroller projects.
- Low power consumption and up to 20 m signal transmission support flexible installations.
Disadvantages
- Measurements require a minimum 2-second interval, limiting rapid sampling applications.
- Humidity accuracy specifications apply to non-condensing conditions at defined test settings.
- Chemical vapors, salt spray, strong UV light, and prolonged extreme conditions can reduce performance.
- At 3.3 V, cable length should not exceed about 100 cm to avoid voltage-drop errors.
Product Specification
Manufacturer
Various
Type
Thermometer (DHT22/AM2302), Hygrometer (DHT22/AM2302)
Platform
Universal
Connectivity
4-pin header, I2C, SPI
Power supply
via host
Dimensions (WxHxD)
0.59 x 0.98 x 0.28 in
Product Description
DHT22/AM2302 Thermometer Hygrometer - Read, Download & Print Free
The DHT22/AM2302 Thermometer Hygrometer is a compact digital sensor designed to measure ambient temperature and relative humidity with dependable accuracy. Combining a capacitive humidity element, a precision temperature sensor, and an onboard microcontroller, it delivers calibrated readings through a simple single-bus data connection. It is a practical choice for makers, students, engineers, and anyone building environmental monitoring projects.
Accurate environmental monitoring
This sensor measures relative humidity from 0 to 99.9% RH with 0.1% RH resolution. Under typical conditions at 25 C, humidity accuracy is rated at plus or minus 2% RH. Temperature measurement covers a wide range from -40 C to 80 C, with 0.1 C resolution and typical accuracy of plus or minus 0.5 C. These capabilities make the DHT22/AM2302 suitable for indoor climate tracking as well as more demanding outdoor or equipment-monitoring applications.
Easy microcontroller integration
The DHT22/AM2302 operates from a 3.3 V to 5.5 V supply, with 5 V recommended. Its digital SDA interface requires only one data line, reducing wiring complexity when connecting to compatible microcontrollers. The sensor sends a 40-bit transmission containing humidity data, temperature data, and a checksum for validation. A pull-up resistor is typically used on the data line to support stable communication.
For reliable measurements, allow the sensor to stabilize for two seconds after power is applied. Readings should also be requested at intervals of at least two seconds. When immediate conditions are important, taking two spaced readings can help obtain the latest measured value.
Built for versatile projects
Low power use, small physical size, and signal transmission distances of up to 20 meters make this thermometer hygrometer flexible for many installations. Common uses include HVAC controls, weather stations, dehumidifiers, data loggers, home automation, appliances, inspection equipment, humidity regulators, and educational electronics projects.
The sensor is factory calibrated, and its calibration coefficients are stored internally. This supports interchangeability between units and helps maintain long-term stability. Its fast response characteristics also help it react to changing humidity and temperature conditions efficiently.
Notes
Install the sensor away from heat-producing components, direct sunlight, condensation, salt spray, and strong chemical vapors. Use quality shielded cable for longer connections, maintain airflow around the sensor, and avoid using it in safety-critical or emergency-stop systems.
Search for 67,706 Manuals online
Type-in Brand or Model
Layne Prohaska
6 months ago
Is this temperature and humidity sensor accurate enough for beginners, or does it need calibration and an oscilloscope?
Manual.ly
6 months ago
The sensor generally provides readings comparable to other units in the same room, but individual devices may show a temperature offset. One review measured approximately 0.6-0.8 C lower values than reference thermometers. It is better suited to users comfortable with electronics and verification; beginners may need guidance, and an oscilloscope can be useful for troubleshooting advanced setups.