Alesis Strike Amp 12 Manual
PDF manual · 36 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your Alesis Strike Amp 12 manual using AI
Get instant AI answers from your Alesis Strike Amp 12 manual
Ask anything about the Alesis Strike Amp 12. Answers come from this manual, with the pages they are based on.
Ask a Question
Do you recommend Strike Amp 12?
Yes NoVideo Manual
Alesis Strike Amp 12 Drum Amplifier/Monitor Overview
Frequently Asked Questions
The Strike Amp 12 includes two XLR/TRS 1/4" combo inputs, one XLR link output for daisy-chaining to another speaker, and an IEC power input. Each input has its own volume control and the unit offers power and signal/limit LEDs.
Is this answer helpful?
Yes. Use a single Strike Amp 12 with the Left (Mono) output from your module for mono. For stereo, connect the module's Left and Right outputs to two Strike Amps. You can also daisy-chain one amp to another via the XLR link output.
Is this answer helpful?
The Contour switch applies a fixed +3 dB boost to low and high frequencies to add presence and fullness, useful on small stages or when drums need extra cut. For a flatter, more neutral sound or maximum headroom, leave Contour disengaged.
Is this answer helpful?
The Signal Limit LED lights green with normal signal and flashes; it turns solid red when output limiting or protection is active. If it stays red, reduce your source or amp volume to prevent distortion or damage.
Is this answer helpful?
The Strike Amp 12 uses electronic clipping protection, thermal protection, and transducer overdrive protection. These systems help prevent damage from prolonged overloads; the unit also uses fuses with specified ratings printed under the power inlet.
Is this answer helpful?
The Strike Amp 12 is rated at 2000 W peak (1000 W RMS) with typical consumption around 800 W. Dimensions are about 23.8" x 13.9" x 13.8" and weight is approximately 35.9 lb (16.3 kg).
Is this answer helpful?
Standard XLR cables or 1/4" (6.35 mm) TRS cables for inputs and XLR cables for linking to another loudspeaker are required and not included. The IEC power cable is included with the unit.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- High peak and RMS power (2000 W peak, 1000 W RMS) for strong stage presence.
- Dedicated LF 12" driver and neodymium HF driver for punchy lows and clear highs.
- Flexible I/O: dual XLR/TRS combo inputs and XLR link output for stereo or daisy-chain setups.
- Contour switch (+3 dB) and ground-lift for quick tonal shaping and hum reduction.
- Robust construction with injection-molded polypropylene enclosure and steel grille.
Disadvantages
- At 35.9 lb (16.3 kg), larger than compact monitors—less ideal for ultra-light travel.
- Contour boost is a fixed +3 dB rather than a parametric EQ for finer tonal control.
- Signal/limit LED indicates clipping but requires manual volume reduction; no auto gain control.
- No onboard digital processing (e.g., FIR/PEQ) for advanced room tuning.
- 800 W consumption may demand careful power planning for multi-speaker rigs.
Product Specification
Type
Drum Monitor
Product Description
Alesis Strike Amp 12 — Powerful, Portable Drum Amplification
The Alesis Strike Amp 12 is a robust, stage-ready powered loudspeaker tailored for electronic drummers and live performers who need clean, punchy sound and reliable connectivity. Built around a 12" low-frequency driver and a neodymium high-frequency driver, the Strike Amp 12 delivers high SPL and extended low-end response while remaining compact enough for rehearsal spaces and small-to-medium venues.
Designed to pair seamlessly with electronic drum modules, the Strike Amp 12 offers versatile routing: run a single unit in mono, link two for stereo, or daisy-chain outputs to expand your rig. The rear panel presents two combo XLR/TRS inputs, an XLR link output, dedicated volume controls per input, and a contour switch that adds a +3 dB lift to lows and highs for more presence on stage. A ground-lift switch helps eliminate hum, and clear signal/limit and power LEDs keep you informed about levels and protection status.
On the technical side, the Strike Amp 12 supplies substantial power—up to 2000 W peak (1000 W RMS) split across dedicated LF and HF sections—yielding a maximum SPL around 131 dB peak. Its frequency response and range emphasize low-end impact (nominal response from 53 Hz up, range down to ~46 Hz) and a focused horn coverage of roughly 90° x 60°, suitable for monitoring and FOH tasks. Built-in protection includes electronic clipping, thermal safeguards, and transducer overdrive protection for dependable performance in demanding situations.
Setup is straightforward: use the supplied IEC power cable, ensure the volume is down before powering on, and connect audio via XLR or 1/4" TRS cables. The enclosure is a trapezoidal, injection-molded polypropylene cabinet with a steel grille for durability and stage resilience. Whether used singularly or paired for stereo, the Strike Amp 12 balances portability, headroom, and clarity for electronic percussionists and small PA applications.
Notes
- Use appropriate fuses when replacing the unit fuse—ratings are printed under the power inlet.
- Reduce input volume if the Signal Limit LED remains red to avoid prolonged clipping.
- Engage Contour for a +3 dB low/high boost; disengage for a flatter live mix.
Search for 67,706 Manuals online
Type-in Brand or Model