Manual.ly Logo

ABL eMH1 Manual

0.0 · 0 Ratings

PDF manual · 34 Pages

English

M: OA-GPT-54-NAN
page

/ 34

Loading...
715ad28a5b902f99c8b287b829d47ec8895c page 7
SAFETY AND OPERATING NOTICES
3
Operating instructions / Maintenance
Please note the following instructions for the operation and maintenance of your
eMH1 Wallbox:
• The device must be connected to the protective earth conductor of your electricity
supply.
• Ensure that the rated voltage and rated current of the device comply with the pa-
rameters of your local electricity grid and that the rated output is not exceeded dur-
ing charging operations.
• At all times comply with local safety regulations for the country in which you operate
the device.
• To disconnect the device completely from the power grid, the power supply must
be cut at your domestic miniature circuit breaker (MCB).
• Follow all information and instructions of the manufacturer for installing and operat-
ing the device.
• Do not operate the device in confined spaces.
• Make sure that the front cover shield is always locked to prevent unauthorized open-
ing of the housing. Keep the key in a place that is known to all authorized users.
• You must not under any circumstances make any changes to the housing or the in-
ternal wiring of the device: Any disregard of this instruction fundamentally breaches
the guarantee provisions and voids the warranty with immediate effect.
• No parts to be maintained by the user are located inside the device.
• Only have qualified, specialist personnel repair and/or install the device.
WARNING!
This Wallbox is intended for connection to and operation on 230 V 50 Hz
or 230 / 400 V 50 Hz mains power only. Power supply cables may be in-
stalled below or above the wall surface. The cable should enter the device
on the underside of the bottom part of the housing (see page 11).
• Only use a dry cloth to clean the device. Do not use aggressive cleaning agents,
waxes or solvents (such as cleaning fluid or paint thinner), because they can dull the
displays on the device.
• The Wallbox must never be cleaned using a pressure cleaner or similar implement.
• Regularly check the charging socket and the separately available charging cable of
your eMH1 Wallbox for wear and tear. Pay special attention to the proper fit of the
connectors of the charging cable in the charging sockets of both the eMH1 and the
vehicle.

Chat with your ABL eMH1 manual using AI

Get instant AI answers from your ABL eMH1 manual

Ask anything about the ABL eMH1. Answers come from this manual, with the pages they are based on.

eMH1 Maintenance Schedule

Remind me when maintenance is due
Semiannual
Test internal RCCB

Open the cover and press the test button to verify the residual current device trips correctly. If it fails, do not use the station.

Show in the manual (page 25)
Regularly
Inspect socket and cable

Check the charging socket and optional cable for damage or defects, ensuring couplings are seated properly.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend eMH1?

Yes No

Frequently Asked Questions

A

It is a wall-mounted AC charging station for electric vehicles, designed for safe Mode 3 charging with a fixed Type 2 cable. It is intended for home or semi-public use where reliable, controlled charging is needed.

Is this answer helpful?

A

The EVSE 563 supports up to 22 kW at 230/400 V and 50 Hz with a rated current of 32 A. Actual charging speed still depends on the vehicle, battery state, and the installed electrical setup.

Is this answer helpful?

A

Yes. The mechanical mounting can be prepared by a user, but all electrical connection work should be carried out by a qualified electrician. The manual strongly emphasizes local electrical rules and safe installation practices.

Is this answer helpful?

A

The unit must be protected by a suitable MCB and an external RCCB. The manual also notes that vehicles may need internal DC fault protection, depending on local regulations and system configuration.

Is this answer helpful?

A

Two LED indicators on the housing show the operating state. They indicate when the unit is ready, when the vehicle is connected, when charging is active, and when charging has finished or an error is present.

Is this answer helpful?

A

Yes, but only in protected locations. The housing has an IP54 rating, so it is suited for covered outdoor areas such as garages or carports rather than places exposed directly to rain or strong sunlight.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 22 kW AC charging supports efficient home and workplace charging.
  • Compact IP54 housing is built for protected indoor or outdoor locations.
  • Fixed Type 2 cable and LED indicators make daily use simple.
  • Lockable cover improves safety and restricts access to internal parts.
VS

Disadvantages

  • Electrical installation must be done by a qualified specialist.
  • An external RCCB and proper MCB protection are required onsite.
  • Not ideal for fully exposed outdoor areas or direct sunlight.
  • Any cable or housing damage means the unit must be taken out of service.
M: OA-GPT-54-NAN

Product Specification

Number of Charging Points

1

Charging Mode

IEC 61851-1 (Mode 3)

Mounting

Wall Mounting

Authorization

no

Interfaces

RS-485

Dimensions

8.70x10.71x4.57in (WxHxD)

M: OA-GPT-54-NAN

Product Description

ABL eMH1 Wallbox: Practical Home Charging with Everyday Confidence

The ABL eMH1 Manual highlights a wallbox designed for drivers who want a straightforward, safe, and efficient way to charge at home or in semi-public settings. The EVSE 563 model is built around a fixed Type 2 charging cable and supports Mode 3 charging, making it a reliable choice for compatible electric vehicles that need up to 22 kW of AC power.

What stands out most is the balance between compact design and strong safety features. The housing is small, durable, and rated IP54, so it is suitable for covered outdoor locations as well as indoor installation. Two LED indicators on the front provide quick status updates, helping users understand whether the unit is ready, charging, or reporting an error without opening the housing.

The eMH1 also keeps daily use simple. The charging connector has a dedicated storage compartment, which helps protect the cable and keeps the station tidy when not in use. A lockable cover shield adds a layer of access control, making it a good fit for households or shared locations where only authorized users should interact with the internal components.

From a performance perspective, the EVSE 563 is rated for 230/400 V, 50 Hz, and 32 A, with a maximum output of 22 kW. That makes it a strong option for faster home charging, while still relying on the vehicle and installation setup to determine the actual charging speed. The manual also stresses the importance of protective earth, an external RCCB, and a suitable MCB, reinforcing that this is a technically mature product intended for proper electrical infrastructure.

Installation is intentionally divided between mechanical mounting and electrical connection. The wall mounting can be prepared with the included drilling template, but the electrical work should be handled by a qualified electrician. This approach supports safe setup while giving users a clear path to positioning the unit conveniently near their vehicle.

Notes

  • Best suited for Type 2 equipped EVs
  • Requires professional electrical installation
  • Designed for protected outdoor or indoor use
  • LED signals simplify daily operation and troubleshooting
  • Follow local regulations and vehicle-specific safety requirements
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly